共找到 327 条与 组合单元和其他装置 相关的标准,共 22 页
JB/T 7175的本部分规定了滚动直线导轨副的参数。 本部分适用于以滚珠为滚动体的滚动直线导轨副。其他滚动体的直线导轨副亦可参照使用。
Rolling linear guide Part 2: Parameters
The content of this document has been tailored to the automotive industry's special requirements for large stamping dies and is intended to serve as a supplement to DIN 9833.
Guide pillars with lead-in chamfer in large stamping dies - Supplement to DIN 9833
This standard specifies dimensions, tolerances, material and finish of guide bushes without collar, with collar and with flange for gliding bushes. They are used for guide pillars in accordance with DIN 9825-2, DIN 9825-3 and DIN 9825-4 in press tool sets.
Tools for pressing - Guide bushes for press tool sets - Part 1: Type AG, Type BG and Type CG, gliding bushes
本标准规定了微动开关通用的基本要求,包含定义,分类,基本参数,技术要求,试验方法,检验规则,标志、包装、运输和贮存等。 本标准适用于在交流50Hz、电压至380V,直流电压至220V的控制或辅助电路中,作控制、信号、联锁之用的开关。
Micro-gap switches
Studs according to this standard are used in conjunction with nuts for T-slots according to DIN 508 as clamping elements for workpieces and fixtures on machine tool tables, pallets and work or clamping devices with T-slots according to DIN 650.#,,#
Studs for use with tee nuts
This standard specifies the dimensions of loose slot stones, to be used in combination with other clamping elements for workpieces of jigs and fixtures on machine tool tables, pallets and clamping devices of workpieces or tools.
Slot stones, loose
This document specifies mounting dimensions for single and double ball nuts units which are to be met for mounting, mainly on machine tools. The specified dimensions shall enable mounting and interchangeability of ball screws of different design and from different manufacturers, without touching design features.
Machine tools - Ball screws - Part 5: Mounting dimensions for ball nuts
The document specifies the dimensions of feet with threaded shank, to be used in combination with other clamping elements for workpieces of jigs and fixtures on machine tool tables, pallets and clamping devices of workpieces or tools.
Feet with threaded shank for jigs and fixtures
Guide to modular coodination in buildings:Part 10:Coordinating sizes and preferred sizes for reinforced concrete components
Guide to modular coodination in buildings:Part 8:Coordinating sizes and preferred sizes for masonry bricks and blocks
Guide to modular coodination in buildings:Part 7:Coordinating sizes and preferred sizes for tiles
Guide to modular coodination in buildings:Part 6:Coordinating sizes and preferred sizes for rigid flat sheets(first revision)
Guide to modular coodination in buildings:Part 5:Coordinating sizes and preferred sizes for windowsets
Guide to modular coodination in buildings:Part 4:Coordinating sizes and preferred sizes for doorsets(first revision)
Guide to modular coordination in buildings:Part 2:Storey heights and room heights(First revision)
Guide to modular coordination in buildings:Part 9:coordinating sizes and preferred sizes for cabinets
Guide to modular coordination in buildings:Part 1:General principles(First revision)
Captive C-washers according to the document are components for fixtures. Combined with pan head screws according to DIN 923 and hexagon nuts according to DIN 6331 they can be used on milling, drilling and grinding fixtures (e.g. NC-machining centers) for a quick and simple clamping of the workpiece.#,,#
Captive C-washer
Parallels are used an exact parallel rest of the workpiece without requirements for the absolute height of support.
Parallels
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号