25.060.20 分度和刀具/工件夹持装置 标准查询与下载
共找到 2191 条与 分度和刀具/工件夹持装置 相关的标准，共 147 页
Cutter arbors with tenon drive - Part 2: Dimensions of 7/24 taper
- ICS
- 25.060.20
- CCS
- J52
- 发布
- 2008-12
- 实施
Modular taper interface with ball track system - Dimensions and designation of receivers
- ICS
- 25.060.20
- CCS
- J52
- 发布
- 2008-11-30
- 实施
- 2008-11-30
Modular taper interface with ball track system - Dimensions and designation of shanks
- ICS
- 25.060.20
- CCS
- J52
- 发布
- 2008-11-30
- 实施
- 2008-11-30
Polygonal taper interface with flange contact surface - Dimensions and designation of shanks
- ICS
- 25.060.20
- CCS
- J52
- 发布
- 2008-11-30
- 实施
- 2008-11-30
Polygonal taper interface with flange contact surface - Dimensions and designation of receivers
- ICS
- 25.060.20
- CCS
- J52
- 发布
- 2008-11-30
- 实施
- 2008-11-30
Machine-tools safety - Safety requirements for the design and construction of work holding chucks
- ICS
- 25.060.20
- CCS
- 发布
- 2008-11-14
- 实施
- 2008-11-14
Hollow taper interface with flange contact surface - Part 3: Dimensions of shanks for stationary tools
- ICS
- 25.060.20
- CCS
- J15
- 发布
- 2008-11
- 实施
Hollow taper interface with flange contact surface - Part 4: Dimensions of receivers for stationary tools
- ICS
- 25.060.20
- CCS
- J15
- 发布
- 2008-11
- 实施
Modular taper interface with ball track system - Part 1: Dimensions and designation of shanks
- ICS
- 25.060.20
- CCS
- J15
- 发布
- 2008-11
- 实施
Modular taper interface with ball track system - Part 2: Dimensions and designation of receivers
- ICS
- 25.060.20
- CCS
- J15
- 发布
- 2008-11
- 实施
Polygonal taper interface with flange contact surface - Part 2: Dimensions and designation of receivers
- ICS
- 25.060.20
- CCS
- J15
- 发布
- 2008-11
- 实施
This European Standard sets out the requirements and/or measures to remove the hazards and limit the risk on work holding chucks which are defined in 3.1. This European standard covers all the hazards relevant to this component. These hazards are listed in clause 4. The requirements of this standard concern designers, manufacturers, suppliers and importers of work holding chucks. This standard also includes information which the manufacturer shall provide to the user. This standard is primarily directed to components which are manufactured after the date of issue of this standard.
Machine-tools safety - Safety requirements for the design and construction of work holding chucks; German version EN 1550:1997+A1:2008
- ICS
- 25.060.20
- CCS
- J50
- 发布
- 2008-11
- 实施
- 2008-11-01
Polygonal taper interface with flange contact surface - Part 1: Dimensions and designation of shanks
- ICS
- 25.060.20
- CCS
- J15
- 发布
- 2008-11
- 实施
This European Standard sets out the requirements and/or measures to remove the hazards and limit the risk on work holding chucks which are defined in 3.1.This European standard covers all the hazards relevant to this component.
Machine-tools safety - Safety requirements for the design and construction of work holding chucks
- ICS
- 25.060.20
- CCS
- 发布
- 2008-09-30
- 实施
- 2008-09-30
This International Standard specifies, with reference to ISO 230-1, the geometric tests and corresponding tolerances for self-centring, manually-operated chucks for machine tools with more than two jaws. This type of chuck has jaws known as “one-piece hard jaws”, the relatively large stroke of which allows quick adaptation to the most varied sizes of workpieces without dismounting. This International Standard deals only with the inspections of rotational accuracy of the chuck, the straightening and the centring of workpieces. It is not applicable to other dynamic quantities, such as measurement of counterbalancing or measurements gripping powers.
Machine tools - Test conditions for self-centring, manually operated chucks with one-piece jaws
- ICS
- 25.060.20
- CCS
- 发布
- 2008-09-11
- 实施
This part of ISO 3442 specifies the sizes for interchangeability of self-centring, manually operated chucks with two-piece jaws (tongue and groove type) and describes, by reference to ISO 230-1, the geometric tests for such chucks. It also specifies the tolerances which apply to these tests.
Machine tools - Dimensions and geometric tests for self-centring chucks with two-piece jaws - Part 1: Manually operated chucks with tongue and groove type jaws
- ICS
- 25.060.20
- CCS
- 发布
- 2008-09-03
- 实施
Machine tools - Tool receiver for hollow taper shanks - Part 1: For Type A and Type C according to DIN 69893, connecting dimensions
- ICS
- 25.060.20
- CCS
- J52
- 发布
- 2008-08-01
- 实施
This European Standard sets out the requirements and/or measures to remove the hazards and limit the risk on work holding chucks which are defined in 3.1. This European standard covers all the hazards relevant to this component. These hazards are listed in clause 4. The requirements of this standard concern designers, manufacturers, suppliers and importers of work holding chucks. This standard also includes information which the manufacturer shall provide to the user. This standard is primarily directed to components which are manufactured after the date of issue of this standard.
Machine-tools safety - Safety requirements for the design and construction of work holding chucks
- ICS
- 25.060.20
- CCS
- J50
- 发布
- 2008-07
- 实施
Covers the material, dimensional, and constructional requirements for metalworkers' bench vices.
Bench vices for metal work (Metric units)
- ICS
- 25.060.20
- CCS
- 发布
- 2008-06-13
- 实施
- 2008-06-13
この規格は，クロスキー形ッーピースジョー付自己求心手動チャック(以下，“チャック”という。)の互換寸法（互換性に関する寸法）及びJIS B 6191に基づき，静的精度検査及び適用する許容値について規定する。
Machine tools -- Dimensions and geometric tests for self-centring chucks with two-piece jaws -- Part 1: Manually operated chucks with tongue and groove type jaws
- ICS
- 25.060.20
- CCS
- J52;J42
- 发布
- 2008-03-20
- 实施
