25.100.20 铣刀 标准查询与下载

ISO 1641-1:2003 端铣刀和槽铣刀.第1部分:直柄铣刀

This part of ISO 1642 specifies the general dimensions of the following milling cutters with plain cylindrical, flatted cylindrical and threaded shanks: — end mills, flat-ended or ball-nosed — standard series and long series; — slot drills — short series and standard series. The dimensional characteristics of cylindrical shanks are in accordance with ISO 3338-1, ISO 3338-2 and ISO 3338-3. NOTE These same milling cutters with Morse taper shanks having a tapped hole are dealt with in ISO 1641-2, those with 7/24 taper shanks in ISO 1641-3. This part of ISO 1641 does not apply to solid hardmetal end mills and slot drills.

End mills and slot drillsPart 1:Milling cutters with cylindrical shanks

GOST 9305-2014 轮廓凸, 凹铣和角圆切刀. 规格

Profile convex, concave milling and corner rounding cutters. Specifications

GOST 32831-2014 带有圆柱形, 莫氏锥柄和7:24锥柄的立铣刀. 尺寸

End mills with cylindrical, Morse taper and 7:24 taper shanks. Dimensions

GOST 26595-2014 带有机夹式可转位刀片的面铣刀. 基准尺寸

Face milling cutters with mechanically clamped indexable inserts. Basic dimensions

GSO ISO 2584:2013 带滑动孔和导向推力的圆柱铣刀 公制序列

This International Standard specifies the dimensions of metric series cylindrical cutters with plain bore and key drive, intended for fitting to cutter arbors. It is applicable to solid cutters and also to interlocking cutters. Solid cutters are made either with straight teeth or with helicoidal teeth angled to the right or left; interlocking cutters are always made with straight or helicoidal teeth angled to the left and right alternately. The range of outside diameters of these cutters is taken from ISO/R 523, Recommended range of outside diameters formilling cutters.

Cylindrical cutters with plain bore and key drive -- Metric series

GSO ISO 8688-2:2013 刀具寿命测试 第1部分：最终铣削

specifies recommended procedures for tool-life testing with high-speed steel tools used for end milling of steel and cast iron workpieces. Can be applied to laboratory as well as to production practice. Considers conditions under which tool deterioration is mainly due to wear. Establishes specifications for workpiece, tool, cutting fluid, cutting conditions, equipment, assessment of tool deterioration and tool life, test procedures, recording, evaluation and presentation of results.

Tool life testing in milling -- Part 2: End milling

GSO ISO 6262-2:2013 阶梯式入口端铣部分 第2部分：锥形柄端铣部分

This part of ISO 6262 specifies the dimensions of end mills with indexable inserts and Morse taper shank according to ISO 296. The form and dimensions of the inserts are left to the discretion of the manufacturer.

End mills with indexable inserts -- Part 2: End mills with Morse taper shank

GSO ISO 22037:2013 具有圆角半径和由实心切削材料制成的圆柱形柄的实心金属边缘分类器 尺寸

This International Standard specifies types and dimensions of solid end mills, with corner radii and cylindrical shanks, made of hard cutting materials in accordance with ISO 513.

Solid end mills with corner radii and cylindrical shanks made of hard cutting materials -- Dimensions

GSO ISO 7755-11:2013 实心金属筋膜钻头 第11部分：前锯齿锥钻头（M形）

This part of ISO 7755 specifies the main dimensions of the cutting part for hardmetal burrs of cone shape, with a pointed nose and designated by the symbol M. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.

Hardmetal burrs -- Part 11: Conical pointed-nose burrs (style M)

GSO ISO 7755-6:2013 实心金属筋膜钻 第6部分：前弧形钻（F 形）

This part of ISO 7755 specifies the main dimensions of the cutting part for hardmetal burrs of arch shape, with a round- (ball-) nose and designated by the symbol F. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.

Hardmetal burrs -- Part 6: Arch round- (ball-) nose burrs (style F)

GSO ISO 7755-12:2013 实心金属锥形钻头 第12部分：倒置锥形钻头（N形）

This part of ISO 7755 specifies the main dimensions of the cutting part for hardmetal burrs of inverted cone shape and designated by the symbol N. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.

Hardmetal burrs -- Part 12: Inverted cone burrs (style N)

GSO ISO 7755-10:2013 实心金属筋膜钻 第10部分：前锥钻（L 形）

This part of ISO 7755 specifies the main dimensions of the cutting part for hardmetal burrs of cone shape, with a round- (ball-) nose and designated by the Symbol L. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.

Hardmetal burrs -- Part 10: Conical round- (ball-) nose burrs (style L)

GSO ISO 7755-2:2013 实心金属旋转钻头 第2部分：圆柱形钻头（图 A）

This part of ISO 7755 specifies the main dimensions of the cutting part for hardmetal burrs of cylindrical shape and designated by the symbol A. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.

Hardmetal burrs -- Part 2: Cylindrical burrs (style A)

GSO ISO 7755-3:2013 实心金属筋膜钻 第3部分：前圆（球）柱钻（C形）

This part of ISO 7755 specifies the main dimensions of the cutting part for hardmetal burrs of cylindrical shape, with a round- (ball-) nose and designated by the symbol C. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.

Hardmetal burrs -- Part 3: Cylindrical round- (ball-) nose burrs (style C)

GSO ISO 1641-3:2013 立铣刀和钻头 第3部分：7/24 锥度轴铣刀的尺寸和标识

This part of ISO 1641 specifies the general dimensions and designation of the following milling cutters with 7/24 taper shanks: — end mills, flat-ended or ball-nosed — normal series and long series (manual changers); — slot drills — short series and normal series (manual changers); — end mills, flat-ended — normal series and long series (automatic changers). Tool shanks with 7/24 taper for manual tool changers are in accordance with ISO 297. Tool shanks with 7/24 taper for automatic tool changers are in accordance with ISO 7388-1 and ISO 7388-2. It is not applicable to end mills and slot drills with cylindrical shank, which are dealt with in ISO 1641-1; it is not applicable to those with Morse taper shank, which are dealt with in ISO 1641-2. This part of ISO 1641 is not applicable to solid hardmetal end mills and slot drills.

End mills and slot drills -- Part 3: Dimensions and designation of milling cutters with 7/24 taper shanks

JB/T 11749-2013 指形齿轮铣刀

本标准规定了指形齿轮铣刀的基本型式和尺寸、技术条件、标志和包装的基本要求。本标准适用于基准齿形角为20°,模数为10 mm~40 mm的指形齿轮铣刀。

Finger geal milling cutters

JB/T 11744-2013 整体硬质合金后波形刃立铣刀

本标准规定了整体硬质合金后波形刃立铣刀的型式与尺寸、技术要求、标志和包装的基本要求。本标准适用于直径φ6 mm~φ20 mm的整体硬质合金后波形刃立铣刀。

Solid carbide rear wave end mill

GSO ISO 7755-8:2013 实心金属筋膜钻头 第8部分：扩口钻头（H形）

This part of ISO 7755 specifies the main dimensions of the cutting part for hardmetal burrs of flame shape and designated by the symbol H. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.

Hardmetal burrs -- Part 8: Flame burrs (style H)

GSO ISO 7755-1:2013 实心金属筋膜钻 第1部分：通用规范

This part of ISO 7755 specifies the common characteristics of hardmetal burrs of various styles, in solid design or with brazed shank. The main dimensions of the cutting part of hardmetal burrs are dealt with individually in ISO 7755-2, ISO 7755-3, ISO 7755-4, ISO 7755-5, ISO 7755-6, ISO 7755-7, ISO 7755-8, ISO 7755-9, ISO 7755-10, ISO 7755-11 and ISO 7755-12.

Hardmetal burrs -- Part 1: General specifications

GSO ISO 7755-5:2013 实心金属筋膜钻 第5部分：椭圆钻（E 形）

This part of ISO 7755 specifies the main dimensions of the cutting part for hardmetal burrs of oval shape and designated by the symbol E. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.

Hardmetal burrs -- Part 5: Oval burrs (style E)