25.100.50 丝锥和板牙 标准查询与下载

KS B 3341-2002(2012) 公制螺纹的短机器抽头和手动抽头

Short machine taps and hand taps for metric threads

SN/T 1060-2002 出口圆板牙检验规程

Rules for the inspection of circular screwing dies for export

UL 745-2-9 BULLETINS-2002

This clause of Part 1 is applicable except as follows: Replacement: This standard applies to tappers.

09/06/2002 (26p)

KS B 3337-2001(2011) 龙头手柄

Tap handles

KS B 3338-2001(2011) 公称直径M3至M24的长柄丝锥－缩径柄丝锥

Long shank taps with nominal diameters fromM3 to M24－Reduced shank taps

LST EN 22857-2001 公差为 4H 至 8H 和 4G 至 6G 粗牙和细牙的 ISO 公制螺纹的磨削螺纹丝锥 螺纹部分的制造公差（ISO 2857:1973 + A1:1984 +A2:1986）

Ground thread taps for ISO metric threads of tolerances 4H to 8H and 4G to 6G coarse and fine pitches - Manufacturing tolerances on the threaded portion (ISO 2857:1973 + A1:1984 +A2:1986)

KS B 3339-2001(2011) 公称直径从M3到10的长柄带凹槽的全直径柄丝锥

Long shank taps with nominal diameters from M3 toM10-Full-diameter shank taps with recess

ABNT NBR 14678-2001 圆形旋盖模具钢导管螺纹Pg7到 Pg48

Round capping die steel conduit thread Pg7 to Pg48

NF E66-107:2000 公称直径为M3 至M10 的长杆螺丝攻.带退刀槽的全直径杆螺丝攻

Long shank taps with nominal diameters from M3 to M10 - Full-diameter shank taps with recess.

ABNT NBR 14517-2000 2水龙头（手动）设置管螺纹G 1 /16至4 G4和Rp1/16至RP4

2 taps (manual) set pipe thread G 1/16 to 4 G4 and Rp1/16 to RP4

ABNT NBR 14516-2000 钢导管螺纹PG 7至48 PG机水龙头

Steel conduit thread PG 7 to 48 PG machine faucet

ABNT NBR 14515-2000 设置2个水龙头钢导管螺纹PG 7 PG48

Set of 2 faucets steel conduit thread PG 7 PG48

DIN 5156:2000 G1/16至G2及Rp1/16至Rp2管螺纹用机用丝锥

The document applies to machine taps intended for manufacturing internal pipe threads where pressure-tight joints are not made on the threads (symbol G) according to DIN ISO 228-1 and whitworth pipe threads for tubes and fittings (symbol Rp) DIN 2999-1. Machine taps according to that standard are not suitable for whitworth pipe threads for pipe couplings in accordance with DIN 3858. DIN 2999-1 shall be replaced by DIN EN 10226-1.

Machine taps for pipe threads, G 1/16 to G 2 and Rp 1/16 to Rp 2

DIN 2189:2000 管螺纹G1/6至G1用冷成形丝锥.尺寸

The document specifies the dimensions of cold-forming taps used to make internal pipe threads where pressure-tight joint are not made on the threads (symbol G) according to DIN ISO 228-1.

Cold-forming taps for pipe threads G 1/6 to G1 - Dimensions

DIN 5157:2000 G1/16至G4和Rp1/16至Rp4管螺纹用二件一套丝锥

The document applies to sets taps consisting of taper tap (V) and finishing tap (F) intended for manufacturing internal pipe threads where pressure-tight joints are not made on the threads (symbol G) according to DIN ISO 228-1 and whitworth pipe threads for tubes and fittings (symbol Rp) DIN 2999-1. Machine taps according to that standard are not suitable for whitworth pipe threads for pipe coupling in accordance with DIN 3858. DIN 2999-1 shall be replaced by DIN EN 10226-1(Entwurf).

Sets of 2 taps for pipe threads G 1/16 to G 4 and Rp 1/16 to Rp 4

DIN 40432:2000 Pg7至Pg48钢管螺纹用二件一套的丝锥

The standard applies to sets of 2 consisting of tapers tap (V) and finishing tap (F) intended for manufacturing steel conduit threads according to DIN 40430.

Sets of two taps for steel conduit thread Pg 7 to Pg 48

DIN 40433:2000 Pg7至Pg48钢管螺纹用机械丝锥

The document applies to machine taps intended for manufacturing steel conduit threads according to DIN 40430.

Machine taps for steel conduit thread Pg 7 to Pg 48

ISO 2283:2000 公称直径从M3～M24和1/8英寸～1英寸的长柄机用丝锥-缩柄丝锥

This International Standard specifies the dimensions for reduced shank taps with nominal diameters from M3 to M24 and 1/8 in to 1 in and thus complements ISO 8051 which concerns full-diameter shank taps. It applies to long shank machine taps. Technical specifications for taps covered by this International Standard (including marking) are given in ISO 8830. This International Standard is applicable to taps intended for cutting the following threads: a) ISO metric threads — coarse pitch; — fine pitch. b) ISO inch threads — "Unified Coarse" series (UNC) and "Unified Fine" series (UNF). The following non-recommended inch threads — "British Standard Whitworth" (BSW) and "British Standard Fine" (BSF); — "British Association" (BA) are given in Annex A.

Long shank taps with nominal diameters from M3 to M24 and 1/8 in to 1 in - Reduced shank taps

ABNT NBR 14427-1999 机水龙头管螺纹G1 / 16 G 2和RP1 / 16，至RP2

Machine faucet pipe thread G1/16, G2 and RP1/16, to RP2

JIS B 4451:1999 手用和机用圆型板牙

この規格は，呼びMl～M68のメートル並目ねじ，呼びMIx0.2～M56X1.5のメートル細目ねじ，呼びNo.I-64UNC～ 2 3/4-4UNCのユニファイ並目ねじ及び呼びNo.0-80UNF～I 1/2-12UNFのユニフアイ細目ねじのねじ切りに用いるねじ切り丸ダイス(以下，ダイスという。)の形状・寸法について規定する。

Hand-and machine-operated circular screwing dies