25.100.50 丝锥和板牙 标准查询与下载

JB/T 10231.8-2016 刀具产品标准检测方法 第8部分：板牙

Standard testing methods for cutting tool products Part 8: Dies

JB/T 12977-2016 钢丝套螺纹丝锥

Wire sleeve threaded tap

ISO 4230:2016 锥管螺纹的手动和机动圆板牙.R系列

Hand- and machine-operated circular screwing dies for taper pipe threads - R series

ISO 4231:2016 圆柱管螺纹的手动和机动圆板牙.G系列

Hand- and machine-operated circular screwing dies for parallel pipe threads - G series

BS ISO 8051:2016 标称直径从M3至M10的长柄丝锥.带凹槽的直径柄丝锥

Long shank taps with nominal diameters from M3 to M10. Full-diameter shank taps with recess

ISO 8051:2016 公称直径从M3～M10的长柄丝锥.带凹槽的直径柄丝锥

Long shank taps with nominal diameters from M3 to M10 - Full-diameter shank taps with recess

DIN 802-3:2016 丝锥螺纹部分的公差.第3部分:根据DIN EN ISO 228-1的管螺纹(G)用丝锥和根据DIN EN 10226-1的管螺纹(Rp).螺纹部分的制造公差

Tolerances on the threaded portion of taps - Part 3: Ground taps for pipe thread (G) according to DIN EN ISO 228-1 and pipe thread (Rp) according to DIN EN 10226-1 - Manufacturing tolerances on the threaded portion

DIN 357:2016 米制ISO普通螺纹M3至M68用螺母丝锥

Machine nut taps for coarse pitch metric ISO-threads M3 to M68

DIN 376:2016-02 米制粗螺距ISO螺纹M1,6至M68机器丝锥

Machine screwing taps for coarse pitch metric ISO-threads M1,6 to M68

DIN 371:2016-01 米制粗螺距ISO螺纹M1至M10和米制细螺距ISO螺纹M1×0.2至M10×1.25带加强柄的机器丝锥

Machine taps with reinforced shank for coarse pitch metric ISO-threads M1 to M10 and fine pitch metric ISO-threads M1 × 0,2 to M10 × 1,25

DIN 374:2016 米制细螺距ISO螺纹M3×0.2至M52×4机器丝锥

Machine screwing taps for fine pitch metric ISO-threads M3 × 0,2 to M52 × 4

JB/T 12757-2015 整体硬质合金切削丝锥

本标准规定了整体硬质合金直槽切削丝锥的型式和基本尺寸、技术要求、标志和包装。 本标准适用于在有色金属及铸铁零件上按GB/T 192～193、GB/T 196～197加工公称直径为1 mm～20 mm的普通米制螺纹的切削丝锥。

Solid carbide cutting tap

JB/T 10232.2-2015 成套螺纹工具 第2部分:技术条件

JB/T 10232的本部分规定了丝锥、板牙及其他附件组装成套的技术要求、标志和包装。 本部分适用于供修配的手用成套螺纹工具。加工米制螺纹M3~M24，统一螺纹No.4~No.12与1/4 in~1 in，60°圆锥管螺纹1/8NPT、1/4NPT、3/8NPT、1/2NPT，55°圆柱管螺纹1/8-28BSP、1/4-19BSP。

Complete set thread tool.Part 2: Technical specifications

JB/T 12756-2015 整体硬质合金挤压丝锥

本标准规定了整体硬质合金挤压丝锥的型式和基本尺寸、技术要求、标志和包装。 本标准适用于在有色金属、低强度黑色金属及其他有良好塑性和韧性的材料上按GB/T 192～193、GB/T 196～197加工公称直径为1 mm～20 mm的普通米制螺纹的挤压丝锥。

Solid carbide thread forming tap

JB/T 10232.1-2015 成套螺纹工具 第1部分:型式和尺寸

JB/T 10232的本部分规定了丝锥、板牙及其他附件组装成套的型式、尺寸、代号和标记等基本要求。 本部分适用于供修配用的手用成套螺纹工具。加工米制螺纹M3~M24，统一螺纹No.4~No.12与1/4 in~1 in，60°圆锥管螺纹1/8NPT、1/4NPT、3/8NPT、1/2NPT，55°圆柱管螺纹1/8-28BSP、1/4-19BSP。

Complete set thread tool.Part 1: Types and dimensions

GSO ISO 8051:2015 公称直径M3至M10的长柄丝锥 带凹槽的全径柄丝锥

This International Standard specifies the dimensions for full-diameter shank taps with recess with nominal diameters from M3 to M10 and thus complements ISO 2283 which concerns relieved shank taps. It applies to long shank machine taps. Technical specifications for taps covered by this International Standard (including marking) are given in ISO 8830.

Long shank taps with nominal diameters from M3 to M10 -- Full-diameter shank taps with recess

GSO ISO 5396:2015 硬质合金镦锻模 术语

This International Standard gives the terminology of the designs of hardmetal heading dies (see table 1) and heading and extruding dies (see table 2) as well as the symbols and corresponding terms for the principal dimensions used for the description of these tools (see table 3). NOTE — In addition to the terms given in two of the three official ISO languages (English and French), this International Standard gives the equivalent terms in German, Italian, Swedish and Dutch; these have been included at the request of ISO Technical Committee 29, and are published under the responsibility of the member bodies for Germany (DIN), Italy (UNI), Sweden (SIS) and the Netherlands (NNI). However, only the terms given in the official languages can be considered as ISO terms.

Hardmetal heading dies -- Terminology

GSO ISO 7226:2015 六角块螺母

This International Standard specifies the general dimensions of hexagonal dienuts for certain sizes of ISO metric threads (coarse and fine pitch series — see ISO 68 and ISO 261), ISO inch threads (UNC and UNF series — see ISO 68 and ISO 263), and pipe threads (G and R series — see ISO 7-1 and ISO 228-1), as well as the non-preferred thread serles BSW, BSF and BA.

Hexagonal dienuts

GSO ISO 2283:2015 公称直径为M3至M24和1/8英寸至1英寸的长柄外螺纹 短柄外螺纹

This International Standard specifies the dimensions for reduced shank taps with nominal diameters from M3 to M24 and 1/8 in to 1 in and thus complements ISO 8051 which concerns full-diameter shank taps. It applies to long shank machine taps. Technical specifications for taps covered by this International Standard (including marking) are given in ISO 8830. This International Standard is applicable to taps intended for cutting the following threads: a) ISO metric threads — coarse pitch; — fine pitch. b) ISO inch threads — "Unified Coarse" series (UNC) and "Unified Fine" series (UNF). The following non-recommended inch threads — "British Standard Whitworth" (BSW) and"British Standard Fine" (BSF); — "British Association" (BA) are given in Annex A.

Long shank taps with nominal diameters from M3 to M24 and 1/8 in to 1 in -- Reduced shank taps

GSO ISO 2284:2015 锥形和平行螺纹管法兰的手动螺纹加工 一般尺寸和标记

This International Standard specifies the general dimensions and marking of hand taps for pipe threads. It is applicable to the two following types of tap : — taps for parallel threads (see table 1), — taps for taper threads (see table 2), having threads in accordance with ISO 7-1 and ISO 228-1. Furthermore, it gives in an annex the bases used for calculation of the dimensions.

Hand taps for parallel and taper pipe threads -- General dimensions and marking