丝锥和板牙标准-分析测试百科网

JB/T 7428-2006 挤压丝锥

本标准规定了普通螺纹挤压丝锥（以下简称丝锥）的型式和基本尺寸、技术要求、性能试验和标志、包装的基本要求。本标准适用于在有色金属及低强度黑色金属零件上按GB/T 192～193、GB/T 196～197加工公称直径2mm～27mm的普通螺纹的丝锥。本标准的丝锥螺纹公差带分为H1、H2、H3 、H4四种，H1、H2、H3通常是磨牙丝锥，H4通常是非磨牙丝锥。

Thread forming tap

ICS: 25.100.50
CCS: J41
发布: 2006-10-14
实施: 2007-04-01

KS B 3343-2006 螺母丝锥

NUT TAPS

ICS: 25.100.50
CCS
发布: 20060929
实施: 20060929

JB/T 10561-2006 硬质合金喷吸钻

本标准规定了硬质合金喷吸钻（以下简称喷吸钻）的型式、尺寸、技术要求、性能试验、标志和包装的基本要求。本标准适用于直径18.4mm～65.0mm的喷吸钻。

Ejector drills with carbide tips

ICS: 25.100.50
CCS: J41
发布: 2006-07-27
实施: 2006-10-11

KS B ISO 2857-2005(2010) 公差和4H〜8H 4G〜6G的粗略度量ISO精磨或使用的标签螺钉间距 - 螺纹的制造公差

Ground thread taps for ISO metric threads of tolerances 4H to 8H and 4G to 6G coarse and fine pitches－Manufacturing tolerances on the threaded portion

ICS: 25.100.50
CCS
发布: 2005-12-23
实施

KS B ISO 8830-2004(2009) 高速钢机用磨牙丝锥技术条件

High-speed steel machine taps with ground threads－Technical specifications

ICS: 25.100.50
CCS
发布: 2004-12-27
实施

DIN 2184-1:2003 丝锥和冷成型丝锥.第1部分:长型.尺寸的一般规划

This standard applies to standardized and non-standardized machine taps and cold forming taps, long type, used to manufacture threads with nominal diameter exceeding 0,90 mm up to 113,00 mm. The general plan contains for some ranges of nominal diameters - dependent on the gradient, number of turns and total length/max. length of thread - two different shanks: reinforced shank (see e.g. DIN 371) and tapered shank (see e.g. DIN 376).#,,#

Taps and cold forming taps - Part 1: Long type; General plan of dimensions

ICS: 25.100.50
CCS: J41
发布: 2003-12
实施

DIN 2184-2:2003 丝锥和冷成型丝锥.第2部分:短型.尺寸的一般规划

Taps and cold forming taps - Part 2: Short type; General plan of dimensions

ICS: 25.100.50
CCS: J41
发布: 2003-12
实施

DIN 40435:2003 符合DIN 8140的ISO米制螺纹钢丝螺套螺纹孔(EG)丝锥.粗螺纹EG M2至EG M52和细螺纹EG M8 1至EG M48?3.尺寸

Machine taps for the tapped holes (EG) for wire thread inserts for ISO metric screw threads according to DIN 8140 - Coarse pitch threads EG M2 to EG M52 and fine pitch threads EG M8 × 1 to EG M48 × 3 - Dimensions

ICS: 25.100.50
CCS: J41
发布: 2003-07
实施

DIN 336:2003 攻螺纹内径用钻头直经

This standard specifies sizes for drills to be used prior to tapping cylindrical screw threads with standard length of engagement where the drill diameter is approximately equal to the nominal thread diameter minus the thread pitch. This standard does not apply to cold-forming tapping. Drill sizes are given for the following screw threads: - ISO metric screw threads (coarse and fine pitch); - EU metric screw threads (coarse and fine pitch); - ISO inch screw threads (UNC and UNF); - Pipe threads.

Diameters of drills for minor diameters of tapped threads

ICS: 25.100.50
CCS: J41
发布: 2003-07
实施

DIN 802-6:2003 生产螺纹丝工线状公差.第6部分:ISO米制粗螺纹和细螺纹用符合DIN 8140的接触钢丝螺套螺纹孔的磨牙丝锥.

This standard specifies the manufacturing tolerances of the threaded portion of taps used to make tapped holes (EG) for wire thread inserts for ISO metric screw threads of tolerance classes 6H mod and 6G mod according to DIN 8140-1 and DIN 8140-2.

Manufacturing to tolerances on the threaded portion of screwing taps - Part 6: Ground taps for tapped holes (EG) for wire thread inserts as in DIN 8140 for ISO metric coarse and fine pitch threads

ICS: 25.100.50
CCS: J41
发布: 2003-07
实施

DIN 2181:2003 套装丝锥.米制ISO细螺纹M1×0,2至M52×4用两件套丝锥

The document applies to sets of 2 taps consisting of taper taps (V) and bottoming taps (F) used for the manufacture of ISO metric fine threads according to DIN 13-2 to DIN 13-9.

Sets of 2 taps for metric fine ISO-threads M1 × 0,2 to M52 × 4