25.100.70 磨料磨具 标准查询与下载

BS ISO 9138:2015 研磨粒料.取样和裂解

Abrasive grains. Sampling and splitting

DIN ISO 525:2015 粘合磨料产品.一般要求(ISO 525-2013)

Bonded abrasive products - General requirements (ISO 525:2013)

ISO 9138:2015 磨粒粒度.取样和裂解

This International Standard specifies the apparatus and the method for sampling and splitting of a lot of abrasive grains, to be used in the comparative testing of uniformly produced abrasive grains.

Abrasive grains - Sampling and splitting

DIN EN ISO 6103:2015 粘合磨料产品.交货时砂轮的可允许不平衡性.静态试验(ISO 6103-2014);德文版本EN ISO 6103-2014

Bonded abrasive products - Permissible unbalances of grinding wheels as delivered - Static testing (ISO 6103:2014); German version EN ISO 6103:2014

GOST R 56578-2015 磨头. 规格

Mounted wheels. Specifications

GOST 33534-2015 磨石和磨瓦. 规格

Grinding stones and segments. Specifications

ASTM C1353/C1353M-15 采用旋转台式磨蚀机的人行道用石材耐磨损性的标准试验方法

5.1 This test method provides a means to quantify the abrasion resistance of dimension stone and may be related to end-use performance, or used to comparatively rank material performance, or both. The resistance of dimension stone to abrasion, as measured on a testing machine in the laboratory, is generally only one of several factors contributing to wear performance as experienced in the actual use of the material. Calculation of predicted life should not be based on specific abrasion data alone. 5.2 The resistance of dimension stone to abrasion may be affected by factors including test conditions; type of abradant; pressure between the specimen and abradant; mounting of the specimen; and type, kind, or amount of finishing materials. 5.3 Abrasion tests utilizing the rotary platform abraser may be subject to variation due to changes in the abradant during the course of specific tests. Depending on abradant type and test specimen, the abrading wheel surface may change (that is, become clogged) due to pick-up of finishing or other materials from test specimens. To reduce this variation, the abrading wheels may require resurfacing. 1.1 This test method covers the establishment of an index of abrasion resistance by determination of loss of volume resulting from abrasion of dimension stone as described in Terminology C119 and is based on Guide G195. 1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.2.1 Exception—The formula for calculation of the result of this test method relies on the use of SI units; all measurements of weight in this test method shall be recorded in SI units. 1.2.2 Exception—As the equipment used in this test method was designed and initially fabricated using dimensions in inch-pound units, the values of equipment dimensions stated in SI units have been given as exact conversions to the nearest 0.1 mm. 1.3 This test method uses a rotary platform abraser to determine the loss in volume of dimension stone caused by abrasion under controlled conditions. 1.4 This test method is useful in indicating the differences in abrasion resistance between the various dimension stones. This test method provides one element in comparing stones of the same type. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic Using a Rotary Platform Abraser

GSO ISO 15635:2014 涂附磨具 百叶轮

This International Standard specifies the nominal dimensions, tolerances and designations of flap discs. It applies to flap discs intended for use on hand held grinding machines without support discs.

Coated abrasives -- Flap discs

GSO ISO 15637-2:2014 圆柱形磨料夹持套筒组件 第2部分：固定机械用夹持组件

This part of ISO 15637 applies to holding fixtures for use with cylindrical abrasive sleeves with D > 100 mm in accordance with ISO 2421. These holding fixtures clamp the cylindrical abrasive sleeves using different systems, e.g. with a lamellar core or using a pneumatic system, which are used on stationary grinding machines.

Holding fixtures of cylindrical abrasive sleeves -- Part 2: Holding fixtures for stationary machines

GSO ISO 16057:2014 涂附磨具 硫化纤维磨盘

This International Standard specifies the nominal dimensions of vulcanized fibre discs. These vulcanized fibre discs are intended for use on hand-held grinding machines. Vulcanized fibre discs are for use with support discs in accordance with ISO 15636.

Coated abrasives -- Vulcanized fibre discs

GSO ISO 13942:2014 固结磨料产品限制挠度和跳动公差

This International Standard specifies the essential limit deviations and run-out tolerances, in millimeters, for bonded abrasive products as specified in ISO 603-1 to ISO 603-16.

Bonded abrasive products -- Limit deviations and run-out tolerances

JB/T 11765-2014 超硬磨料 纳米金刚石

本标准规定了超硬磨料纳米金刚石的术语和定义、代号和标记、技术要求、试验方法、检验规则、标志、包装与贮存。 本标准适用于爆轰法合成的纳米金刚石。

Superabrasive.Nanodiamond

KS L ISO 603-6-2014(2019) 粘合磨料产品 - 尺寸 - 第6部分:研磨轮用于工具和工具室研磨

Bonded abrasive products — Dimensions — Part 6: Grinding wheels for tool and tool room grinding

KS L ISO 603-4-2014(2019) 粘合磨料产品 - 尺寸 - 第4部分:磨削轮用于表面磨削/外围磨削

Bonded abrasive products — Dimensions — Part 4: Grinding wheels for surface grinding/peripheral grinding

KS L ISO 603-7-2014(2019) 粘结磨料产品 - 尺寸 - 第7部分:手动导向磨削砂轮

Bonded abrasive products — Dimensions — Part 7: Grinding wheels for manually guided grinding

KS L ISO 603-3:2014 黏合磨料产品 尺寸 第3部分：内圆磨砂轮

Bonded abrasive products — Dimensions — Part 3: Grinding wheels for internal cylindrical grinding

KS L ISO 603-3-2014(2019) 粘结研磨产品 - 尺寸 - 第3部分:内圆磨削砂轮

Bonded abrasive products — Dimensions — Part 3: Grinding wheels for internal cylindrical grinding

KS L ISO 603-4:2014 黏合磨料产品 尺寸 第4部分：平面磨/外圆周磨砂轮

Bonded abrasive products — Dimensions — Part 4: Grinding wheels for surface grinding/peripheral grinding

KS L ISO 603-13-2014(2019) 粘结磨料产品 - 尺寸 - 第13部分:用于在垂直磨床上去毛刺和剥皮的砂轮

Bonded abrasive products — Dimensions — Part 13: Grinding wheels for deburring and fettling on a vertical grinder

KS L ISO 603-12-2014(2019) 粘合研磨产品 - 尺寸 - 第12部分:用于在直磨机上去毛刺和剥皮的砂轮

Bonded abrasive products — Dimensions — Part 12: Grinding wheels for deburring and fettling on a straight grinder