25.140.01 手持工具综合 标准查询与下载

KS B ISO 2380-2-2022 螺钉、螺母装配工具 开槽螺钉用螺丝刀 第2部分：手动螺丝刀的一般要求、刀片长度和标记

Assembly tools for screws and nuts－Screwdrivers for slotted-head screws－Part 2：General requirements, lengths of blades and marking of hand-operated screwdrivers

KS B ISO 2380-1-2022 螺钉和螺母装配工具 一字螺钉螺丝刀 第1部分：手动和机用螺丝刀的使用技巧

Assembly tools for screws and nuts－Screwdrivers for slotted-head screws－Part 1：Tips for hand-and machine-operated screwdrivers

T/NJZZ 01-2022 钢锄通用技术条件

技术要求： 1为适用钢锄品种、规格多样性特点，从实用性出发，标准对钢锄基本尺寸偏差、质量偏差提出要求，给出了常规产品的尺寸参考值，大大增加标准的适用范围。 将标准名称由《钢锄》确定为《钢锄通用技术条件》。 2 参考QB/T 2095-1995《钢锹》、NY/T 380-1999《机制钢锹质量分等》、NY/T 379-1999《机制钢锹》和QB/T 2290-1997《钢镐》等标准的框架，结合钢锄特点，在标准中明确了外观质量要求。 3 为确保钢锄质量，依据各企业生产实际，明确了淬火区域不少于身长的1/2（适用淬火钢锄）；分析综合检测数据，确定了普通钢锄硬度（20-40）HRC；高强度钢锄硬度（41-50）HRC。 规定条件下冲击试验不炸裂、不变形。

General technical conditions for steel hoes

T/SDWJ 002-2022 液化气喷火枪

本标准规定了液化气喷火枪的产品分类、技术要求、试验方法、检验规则及标志、包装、运输与贮存。

Liquefied gas spray gun

T/SDWJ 004-2022 压胶枪

3 要求 3.1 外观质量 3.1.1钣金件、冲压件表面应无重皮、明显机械损伤及凹凸不平等缺陷。 3.1.2镀层和涂层应色泽均匀，无明显剥落、起泡、划伤等缺陷。 3.1.3焊缝件均匀，无裂缝、烧焦、咬边等缺陷；被夹在固定螺丝和手柄间的部分焊接面应平整。 3.1.4锻铸件表面应无流痕、缺料、裂缝、起泡、脱皮等缺陷。 3.2 性能要求 3.2.1使用性能 压胶枪在正常使用过程中，应能顺利出胶。 3.2.2跌落性能 压胶枪经跌落测试后，仍能正常出胶。 3.2.3压胶时的打击力 压胶枪压胶时的打击力应在800N～1200N之间，压胶枪铝管式打击力1500N 3.2.4同心度 压胶枪推进杆能顺畅插拔，推进杆同左右筋要平行，推进过程中推进杆头部 不翘起，推进杆到顶部前圈中，推进盘不偏离±3mm。 3.2.5手柄的抗冲击试验 经冲击试验后，手柄无机械性损伤或断裂。 3.2.6推进步数 不得大于27次。

Glue gun

DIN ISO 1711-1:2021 螺钉和螺母用装配工具. 技术规范. 第1部分: 手动扳手和套筒(ISO 1711-1-2019)

This document contains minimum values for Rockwell hardness and torsional strength for hand-operated wrenches and sockets.

Assembly tools for screws and nuts - Technical specifications - Part 1: Hand-operated wrenches and sockets (ISO 1711-1:2019)

DIN ISO 1711-2:2021 螺钉和螺母的装配工具. 技术规格. 第2部分: 机动套筒(冲击)(ISO 1711-2-2019)

This document contains hardness and minimum torsional strength for machine-operated square drive sockets in accordance with ISO 2725-2 intended for use with impact wrenches.

Assembly tools for screws and nuts - Technical specifications - Part 2: Machine-operated sockets (impact) (ISO 1711-2:2019)

KS B 3038-2020 夹钳

Clamp

KS B 7354-2019 铲子及其盖

Field shovel and its cover

KS B ISO 2351-2:2019 螺钉和螺母装配工具机用螺丝刀头第2部分:十字槽螺钉用螺丝刀头

Assembly tools for screws and nuts－Machine－operated screwdriver bits－Part 2：Screwdriver bits for cross－recessed head screws

KS B ISO 2351-2-2019 螺钉和螺母装配工具机用螺丝刀头第2部分:十字槽螺钉用螺丝刀头

Assembly tools for screws and nuts－Machine－operated screwdriver bits－Part 2：Screwdriver bits for cross－recessed head screws

BS ISO 1711-1:2019 螺钉和螺母的装配工具 技术规格 手动扳手和套筒

What is BS ISO 1711-1 - wrench and socket technical specifications about?    BS ISO 1711-1 specifies minimum values for Rockwell hardness and torsional strength for hand-operated wrenches and sockets. BS ISO 1711-1 covers the following three series of torsion torques:   Series A: usual box wrenches and socket wrenches   EXAMPLE 1 Reference nos. 1 1 02 01 0; 1 1 02 02 0 and 1 1 02 02 1; 1 1 02 03 0; 1 1 02 04 0; 1 1 02 05 0; 1 1 02 06 0; 1 1 02 09 0; 1 1 02 10 0; 1 1 02 11 0; 1 1 02 12 0; 1 1 02 13 0...

Assembly tools for screws and nuts. Technical specifications - Hand-operated wrenches and sockets

BS ISO 1711-2:2019 螺钉和螺母的装配工具 技术规格 机械操作套筒（冲击）

What is BS ISO 1711-2 – machine-operated sockets technical specifications about?    Impact sockets are used with powered impact wrenches or drivers where greater force can be applied. Impact sockets are usually used by mechanics to remove seized nuts and bolts from vehicles. Impact sockets are designed to cope with the vibration caused by an impact wrench.    BS ISO 1711-2 specifies hardness and minimum torsional strength for machine-operated square drive sockets in accordance with ISO 2725-2 intended for use with impact wrenches.   Example:   Reference nos. 2 2 02 01 0; 2 2 02 02 0; 5 2 00 04 0.

Assembly tools for screws and nuts. Technical specifications - Machine-operated sockets (impact)

ISO 1711-1:2019 螺丝和螺母装配工具 - 技术规格 - 第1部分:手动扳手和插座

This document specifies minimum values for Rockwell hardness and torsional strength for hand- operated wrenches and sockets. It covers the following three series of torsion torques: — Series A: usual box wrenches and socket wrenches; EXAMPLE 1 Reference nos. 1102010; 1102020 and 1102021; 1102030; 1102040; 1102050; 1102060; 1102090; 1102100; 1102110; 1102120; 1102130 and 1102131; 1102140; 1102150; 1108010; 1108020. — Series C: open end wrenches; EXAMPLE 2 Reference nos. 1101010; 1101011; 1101020; 1101030; 1101040. — Series E: hand-operated square drive sockets. EXAMPLE Reference nos. 2102010 and 2102011. NOTE The wrenches and sockets mentioned above are listed under their respective reference numbers in

Assembly tools for screws and nuts — Technical specifications — Part 1: Hand-operated wrenches and sockets

ISO 1711-2:2019 螺丝和螺母的装配工具 - 技术规格 - 第2部分:机器操作的插座（冲击）

This document specifies hardness and minimum torsional strength for machine-operated square drive sockets in accordance with ISO 2725-2 intended for use with impact wrenches. EXAMPLE Reference nos. 2202010; 2202020; 5200040. NOTE The sockets mentioned above are listed under their respective reference numbers in ISO 1703.

Assembly tools for screws and nuts — Technical specifications — Part 2: Machine-operated sockets (impact)

ASME B107.4-2019 便携式手动,碰撞式,气动和电动工具(冲击工具除外)用传动端和主轴端

This Standard applies to portable power tools for drilling, grinding, polishing, sawing, and driving threaded fasteners,and hand tools for driving threaded fasteners. Other tools not classed as percussion tools belong in this category and may be added by revision or addition through the usual procedure. This Standard includes dimensions and tolerances for both driving and driven elements where such coordination is important and not established by reference to the pertinent American National Standards. All dimensions are in inches and millimeters. 本标准适用于钻孔、研磨、抛光、锯切和驱动螺纹紧固件的便携式电动工具，以及用于驱动螺纹紧固件的手动工具。其他未归类为打击工具的工具也属于此类，通过通常的程序修改或添加。 本标准包括主动和从动元件的尺寸和公差很重要且未参考相关美国国家标准而建立。所有尺寸均以英寸和毫米为单位。

Driving and Spindle Ends for Portable Hand, Impact, Air, and Electric Tools (Percussion Tools Excluded)

ISO/TR 20571:2018 Dynaload - 设计 - 施工 - 使用和维护

Dynaload — Design and construction — Use and maintenance

18/30378802 DC BS ISO 1711-2 AMD1 螺钉和螺母的装配工具 技术规格 第 2 部分：机操作插座（冲击）

BS ISO 1711-2 AMD1. Assembly tools for screws and nuts. Technical specifications - Part 2. Machine-operated sockets (impact)

18/30378799 DC BS ISO 1711-1 AMD1 螺钉和螺母的装配工具 技术规格 第 1 部分：手动扳手和套筒

BS ISO 1711-1 AMD1. Assembly tools for screws and nuts. Technical specifications - Part 1. Hand-operated wrenches and sockets

KS B 7359-2018 三重铲

Three fold field shovel