25.140.01 手持工具综合 标准查询与下载

BS ISO 2725-3:2001 螺钉和螺母用装配工具.方形传动套筒.机用套筒(无冲击).尺寸

This part of ISO 2725 specifies dimensions, designation and marking of machine operated "non-impact" square drive sockets. NOTE 1 Machine operated "non-impact" square drive sockets are listed under number 301 in ISO 1703:1983. NOTE 2 Hand-operated sockets are dealt with in ISO 2725-1. Machine-operated "impact" sockets are dealt with in ISO 2725-2.

Assembly tools for screws and nuts - Square drive sockets - Machine-operated sockets ("non-impact") - Dimensions

DLA GGG-C-475 B VALID NOTICE 2-2001 毛发剪刀

GGG-C-475B, dated 23 OCTOBER 1973, has been reviewed and determined to be valid for use in acquisition.

CLIPPERS, HAIR, HAND

NF E74-363-3:2001 螺钉和螺母用装配工具.方形驱动套筒.第3部分:机器驱动套筒(无冲击).尺寸

Assembly tools for screws and nuts - Square drive sockets - Part 3 : machine-operated sockets ("non impact") - Dimensions.

ISO 2725-3:2001 螺钉和螺母用装配工具 方头传动套筒 第3部分：机动套筒（非撞击） 尺寸

This part of ISO 2725 specifies dimensions, designation and marking of machine operated "non-impact" square drive sockets. NOTE 1 Machine operated "non-impact" square drive sockets are listed under number 301 in ISO 1703:1983. NOTE 2 Hand-operated sockets are dealt with in ISO 2725-1. Machine-operated "impact" sockets are dealt with in ISO 2725-2.

Assembly tools for screws and nuts - Square drive sockets - Part 3: Machine-operated sockets ("non impact"); Dimensions

NP EN 1454-2000 内燃型便携式手持切割设备．相关的安全要求

1 A presente Norma Europeia aplica-se a máquinas concebidas para cortar, em especial para cortar materiais de constru??o, mas que podem também ser utilizadas para cortar metais, em fun??o do tipo específico de disco de cortar seleccionado (ver figura 1). NOTA: No que se refere às dimens?es nominais e à velocidade periférica dos discos de cortar, ver sec??o 5.7.1. A presente Norma Europeia especifica os requisitos de concep??o e de constru??o, incluindo seguran?a, desempenho e ensaios, para máquinas de cortar portáteis, manuais e com motor de combust?o interna (ver figura 1). Em complemento, a presente Norma Europeia especifica a informa??o que deverá ser fornecida pelo fabricante sobre práticas de trabalho seguras.2 A presente Norma Europeia trata de todos os perigos significativos relativos às máquinas de cortar, quando estas sejam utilizadas da forma adequada (ver sec??o 3.12 da EN 292-2:1991) e nas condi??es previstas pelo fabricante (ver sec??o 4). A presente Norma Europeia especifica as medidas técnicas adequadas para eliminar ou reduzir os riscos resultantes dos perigos significativos.3 A presente Norma Europeia aplica-se, em especial, às máquinas fabricadas depois da data da aprova??o da norma pelo CEN.

Portable,hand-held,internal combustion cutting-off machines Safety

EN 792-13:2000 手持非电动工具.安全要求.第13部分:紧固件传动工具;包含修改件A1-2008

This standard is applicable to fastener driving tools which are handled by one person and in which energy in a linear movement is applied to a loaded fastener for the purpose of drivingThis into a workpiece of a determined material. During the driving operation; the fastener leaves the tool partially or entirely; with sufficient velocity to overcome the resistance of penetration; and forms a mechanical connection or attachment of different workpieces. The energy required for driving a fastener is provided by compressed air or combustible gases. NOTE 1 Fastener driving tools are also referred to for example as Nailers; Staplers; Tackers; Pinners. NOTE 2 The workpiece material can; for example; consist of wood; wooden materials; plastic material; fibre materials loose or condensed; cement- and lime materials; metal.This standard contains requirements for the design; marking and information for use of fastener driving tools; corresponding to the specific hazards listed in clause 4. The standard sets out the means of verification for these requirements. Where; for clarity; an example of a safety measure is given in the text;This shall not be considered as the only possible solution. Any other solution leading to the same risk reduction is permissible if an equivalent level of safety is achieved.This standard is applicable to fastener driving tools which have been produced after the date of publication of the standard.This standard is not applicable to stapling pliers and vibration hammers. NOTE 3 "Stapling pliers" are handheld power operated tools equipped with a fixed or moving anvil bar in front of the muzzle; which are used predominantly for joining paper; leather; textiles and similar materials.This standard is not applicable to fastener driving tools in which the energy for driving fasteners is drawn from cartridges or from any type of electric supply.

Hand-held non-electric power tools - Safety requirements - Part 13: Fastener driving tools (Incorporates Amendment A1: 2008)

AIA/NAS NASM35793-1999 FSC 5340型普通孔外部装置手柄

Handle, Bail-Chest, Surface Mounting, Plain Holes FSC 5340

Handle, Bail-Chest, Surface Mounting, Plain Holes

AIA/NAS NASM35791-1999 FSC 5340型外部安装孔埋头钉手柄

Handle, Bail-Chest, Surface Mounting Countersunk Holes FSC 5340

Handle, Bail-Chest, Surface Mounting Countersunk Holes

JB/T 3411.38-1999 侧面孔钩扳手.尺寸

　　本标准规定了侧面孔钩扳手的型式和尺寸。 　　本标准适用于装卸GB 816-1988《侧面孔小圆螺母》、JB/T 8004.4-1995《机床夹具零件及部件 调节螺母》及JB/T 8004.5-1995《机床夹具零件及部件 带孔滚花螺母》的侧面孔钩扳手。

Pin wrench.Dimensions

NF E74-352:1998 螺钉和螺母的装配工具.槽头螺钉的丝锥.第1部分:手操作及机械操作的丝锥锥尖

Assembly tools for screws and nuts. Screwdrivers for slotted-head screws. Part 1 : tips for hand- and machine-operated screwdrivers.

DLA MIL-B-85667 A (2)-1998 通用技术要求凸出及埋头螺钉头直手柄轴套螺钉

This amendment forms a part of Military Specification MiL-B-85667Ar dated 28 January 1991, and is approved for use by all Departments and Agencies of the Department of Defense.

BOLT, SLEEVE, STRAIGHT SHANK, PROTRUDING AND FLUSH HEAD, GENERAL SPECIFICATION FOR

AIA/NAS NASM17990-1998 FSC 5315型环形手柄双向运作锁快速断路栓

NASMl7990, "PIN, QUICK RELEASE, POSITIVE LOCKING, DOUBLEA CTING, RING HANDLE:", was adopted on 30 NOVEMBER 1998 for use by the Department of Defense (DoD). Proposed changes by DoD Activities must be submitted to the DoD Adopting Activity: Defense Industrial Supply Center, ATTN: DISC-AESD, 700 Robbins Avenue, Philadelphia, PA 19111-5096. DoD Activities may obtain copies of this standard from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094. The private sector and other Government agencies may purchase copies from the AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC., 1250 EYE STREET, N. W., WASHINGTON, DC 20005-3924.

Pin, quick release, positive locking, double acting, ring handle

AIA/NAS NASM39087-1998 FSC 5340型弓形手柄

All surfaces to be finished after fabrication.

Handle, Bow

AIA/NAS NASM35792-1998 FSC 5340型凹槽手柄

Handle, Bail Chest, Recessed FSC 5340

Handle, Bail Chest, Recessed

AIA/NAS NASM17987-1998 FSC 5315型环形手柄单向运作锁快速断路栓

NASM17987, ”PIN, QUICK RELEASE, SELF-RETAINING, POSITIVE LOCKING, SINGLE ACTING, RING HANDLE‘’, was adopted 3o1n DECEMBER 1998 for use by the Department of Defense (DoD). Proposed changes by DoD Activities must be submitted to the DoD Adopting Activity: Defense Industrial Supply Center, ATTN: DISC-AESD, 700 Robbins Avenue, Philadelphia, PA 19111-5096. DoD Activities may obtain copies of this standfarrodm the Standardization Document Order Desk, 700 Robbins Avenue, Building 40, Philadelphia, PA 19111-5094. The private sector and other Government agencies may purchase copies from the

Pin, quick release, self-retaining, positive locking, single acting, ring handle [Superseded: DLA MS17987 REV G CANC NOTICE 1, DLA MS17987 REV G, DLA MS17987 REV F, DLA MS17987 REV E, DLA MS17987 REV D, DLA MS17987 REV C]

AIA/NAS NASM17984-1998 FSC 5315型扣住手柄单独运作锁快速断路栓

NASM17984, "PIN, QUICK RELEASE, SELF-RETAINING, POSITIVE LOCKINGS,I NGLE ACTING, BUTTON HANDLE", was adopted on 30 NOVEMBER 1998 for use by the Department of Defense (DoD). Proposed changes by DoD Activities must be submitted to the DoD Adopting Activity: Defense Industrial Supply Center, ATTN: DISC-AESD, 700 Robbins Avenue, Philadelphia, PA 19111-5096. DoD Activities may obtain copies oft his standard from the Standardization Document Order Desk, 700 Robbins Avenue, Building4 D, Philadelphia, PA 19111-5094. The private sector and other Government agenciemsa y purchase copies from the AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC., 1250 EYE STREET, N. W., WASHINGTON, DC 20005-3924.

Pin, quick release, self-retaining, positive locking, single acting, button handle [Superseded: DLA MS17984 REV F CANC NOTICE 1, DLA MS17984 REV F, DLA MS17984 REV E, DLA MS17984 REV D, DLA MS17984 REV C]

NF E63-403:1997 便携式手持内燃切割机.安全性

Portable, hand-held, internal combustion cutting-off machines. Safety.

ISO 2380-1:1997 螺钉和螺母用装配工具 一字槽螺钉旋具 第1部分:手工和机用螺钉旋具工作部

Assembly tools for screws and nuts - Screwdrivers for slotted-head screws - Part 1: Tips for hand- and machine-operated screwdrivers

KS B 3345-1997(2012) 博尔特快船

Bolt clippers

ARMY MIL-L-45522 A NOTICE 2-1997 M21A1型7.62MM手柄式装链机

This notice should be filed in front ofMIL-L-45522A, dated 30 November 1973 MIL-L-45522A, dated 30 November 1973 and Validation notice 1, dated 26 July 1988 is inactive for new design and is no longer used, except for replacement purposes.

LINKER-DELINKER, HAND, 7.62MM, M21A1