25.140.99 其他手持工具 标准查询与下载

NF E27-819:2011 模块.操作的手持工具.安全要求.修复和标记工具.

Cartridge-operated hand-held tools - Safety requirements - Fixing and marking tools.

BS EN 15895:2011 弹药推动的手持式工具.安全性要求.固定和硬标记工具

This European standard covers safety requirements for cartridge operated fixing and hard marking tools which operate with an intermediate member (piston). This European standard deals with all significant hazards, hazardous situations and events relevant to cartridge operated fixing and hard marking tools, when they are used as intended and under conditions of misuse which are reasonably foreseeable (see Clause 4). It deals with the significant hazards in the different operating modes and intervention procedures as referred to in EN ISO 12100-1:2003, 5.3. Although the safe use of cartridge operated tools depends to an important extent on the use of appropriate cartridges and fasteners, this standard is not formulating requirements for the cartridges and fasteners to be used with the tools (see Clause 7). This European Standard applies to tools designed for use with cartridges with casings made of metal or plastic and with solid propellant and containing a minor quantity of primer with a composition different from that of the main propellant. The fixing tools in the scope are those intended for use with fasteners made from metal. NOTE Information about cartridges can be found in the publication of the Permanent International Commission for the Proof of Small Arms (C.I.P.). This European standard is not applicable to cartridge operated fixing and hard marking tools which are manufactured before the date of its publication as EN.

Cartridge operated hand-held tools. Safety requirements. Fixing and hard marking tools

JB/T 5557-2007 液压转矩扳手

本标准规定了液压转矩扳手（以下简称扳手）的型式、基本参数和主要尺寸、技术要求、试验方法 和检验规则、标志、包装和贮存。 本标准适用于紧固符合GB/T 3098.1、GB/T 3098.2规定、螺纹直径为M16～M120的各种六角头、方头、内六角头螺纹紧固件、公称转矩为2500N·m～80000N·m 的扳手。环境温度-20℃～+50℃。

Wrench with hydraulic cyliuder

DIN 5117:2004 可调节的螺旋夹钳

This standard specifies the dimensions and test values of the adjustable srew clamps. Adjustable screw clamps according to this standard are used as workpiece locating fixtures.

Adjustable screw clamps

GOST 30701-2001 手持电动工具.打钉器的特殊安全要求和测试方法

Настоящий стандарт устанавливает требования безопасности и методы испытаний электрических ручных скобозабивных машин, которые дополняю

Electric hand-held tools. Particular safety requirements and methods of testing tackers

ARMY MIL-S-52408 C NOTICE 3-1998 有10吨载量起重车的伸缩式吊索展平锤

This notice should be filed in h n t of MIL-C-S2408C, dated 19 December 1989.

SPREADER, SLING: TELESCOPIC, VEHICLE LIFTING, 10 TON CAPACITY

BS 3066:1995 工程用冷凿及相关工具规范

This British Standard specifies the nominal sizes, dimensions, quality, finish and testing of engineers' cold chisels and allied tools for hand use as follows: - flat chisels; - cross-cut chisels; - half-round nose chisels; - diamond-point chisels; - brick bolsters; - floorboard chisels; - plugging chisels; - concrete or moil points; - parallel pin punches; - taper punches (including nail and reaper punches); - centre punches.

Specification for engineers' cold chisels and allied tools

IEC 60745-2-16:1993 手持式电动工具的安全 第2-16部分:铆钉机的特殊要求

Is intended to be used with the first edition of IEC 745-1: Safety of hand-held motor-operated electric tools, Part 1: General requirements; it lists the changes necessary to convert that part: replaces definition 2.2.23, adds new definition 2.2.101 (Tac

Safety of hand-held motor-operated electric tools; part 2: particular requirements for tackers

GOST 27570.27-1991 家用和类似用途电气应用的安全 便携式电热工具和类似器具的特殊要求和试验方法

Safety of household and similar electrical application. Particular requirement for portable electric heating tools and similar appliances and test methods

ARMY MIL-S-52408 C-1989 有10吨载量起重车的伸缩式吊索展平锤

this specification mers a tubular-steel telescopic sling spmder.

SPREADER, SLING: TELESCOPIC, VEHICLE LIFTING, 10 TON CAPACITY

NF E71-101:1983 推进力控制的安装设备.试验

Propellant actuated fixing equipement. Tests.

NF E71-100:1983 推进力控制的安装设备.一般要求

Propellant actuated fixing equipment. General requirements.

NF E71-105:1983 封焊、开采和其他相似机械.配接套管.特征

Cartridges for wall sealing, blasting and similar appliances. Technical characteristics.

GOST 25726-1983 字符和数字的手用钢印.型式和基本尺寸

Letter and numerical hand stamps. Types and basic dimensions

GOST 25727-1983 字符和数字的手用钢印.技术条件

Letter and numerical hand stamps. Specifications

ASME B18.3.2M-1979 米制系列六角板手和板手头

This standard contains the complete dimensional,mechanical and performance requirements forMetric Series Hexagon Keys and Bits of nominal sizesfrom 0.7 mm to 36 mm recognized as “AmericanNational Standard.” They are primarily intended tobe used for tightening and loosening metric serieshexagon socket screw products but may also be suitablefor use on other products having metric hexagonsocket wrenching provisions.1.1.2 The inclusion of dimensional data in this standardis not intended to imply that all the productsdescribed are stock production sizes. Consumers arerequested to consult with manufacturers concerninglists of stock production sizes.

Metric Series Hexagon Keys and Bits

AS/NZS 1873.2:2003 手持型射钉器.设计和施工

Sets out requirements for the design, construction and performance of both direct-acting and indirect-acting powder-actuated (PA) hand-held tools. Appendices include methods for measuring the velocity of fasteners discharged from PA tools and for determi

Powder-actuated (PA) hand-held fastening tools - Design and construction

AS/NZS 1873.4:2003 手持型射钉器.紧固件

Sets out requirements for fasteners intended for use with powder-actuated (PA) hand-held fastening tools complying with AS/NZS 1873.2.

Powder-actuated (PA) hand-held fastening tools - Fasteners

AS/NZS 1873.1:2003 手持型射钉器.选择、操作和维护

Provides guidance on the selection, operation and maintenance of powder-actuated (PA) hand-held fastening tools.

Powder-actuated (PA) hand-held fastening tools - Selection, operation and maintenance