25.160.10 焊接工艺 标准查询与下载

UNI EN ISO 25239-5:2020 摩擦搅拌焊 铝 第5部分：质量和检验要求

Friction stir welding - Aluminium - Part 5: Quality and inspection requirements

UNI EN ISO 25239-1:2020 摩擦搅拌焊 铝 第1部分：词汇

Friction stir welding - Aluminium - Part 1: Vocabulary

UNI EN ISO 25239-4:2020 摩擦搅拌焊 铝 第4部分：焊接程序的规范和鉴定

Friction stir welding - Aluminium - Part 4: Specification and qualification of welding procedures

T/CWAN 0039-2020 船舶纵骨角焊缝机器人焊接工艺规范

本文件规定了船舶纵骨角焊缝机器人的术语和定义、一般要求、焊接设备、焊接材料及焊接工艺要求、焊后检测及安全防护等。 本文件适用于一般强度船体结构钢（A、B、D和E）、高强度船体结构钢（AH32、DH32、EH32、AH36、DH36和EH36）的船舶纵骨角焊缝横角焊位置的双电极自动焊接。

Specification for Welding Procedure of Ship Longitudinal Fillet Weld Robot

BS EN ISO 25239-4:2020 搅拌摩擦焊 铝 焊接工艺规范和鉴定

What is   ISO 25239 ‑ 4   about? ISO 25239-4  is the fourth part of a multi-series international standard that covers the  friction stir welding of aluminium. ISO 25239‑4  specifies the requirements for the specification and qualification of welding procedures for the friction stir welding (FSW) of aluminium. It gives you specifications such as development and qualification of welding procedures, qualification based on a welding procedure test and qualification based on pre-production welding test. The term “aluminium” refers to aluminium and its alloys here. Note 1:   ISO 25239‑4  focuses on the friction stir welding (FSW) of aluminium because, at the time of publication of this standard, the majority of commercial applications for friction stir welding (FSW) involved aluminium metal. Note 2:   ISO 25239‑4  does not apply to friction stir spot welding which is covered by the ISO 18785 series. Note 3:   Service requirements, materials or manufactu...

Friction stir welding. Aluminium - Specification and qualification of welding procedures

BS EN ISO 25239-5:2020 搅拌摩擦焊 铝 质量和检验要求

What is   ISO 25239 ‑ 5   about? ISO 25239-5  is the fifth part of a multi-series international standard that covers the  friction stir welding of aluminium.   ISO 25239‑5  specifies a method for determining the capability of a manufacturer to use the friction stir welding (FSW) process for the production of products of the specified quality. It specifies quality requirements but does not assign those requirements to any specific product group. The term “aluminium” refers to aluminium and its alloys. Note 1:   ISO 25239‑5   focuses on the friction stir welding (FSW) of aluminium because, at the time of publication of this standard, the majority of commercial applications for Friction stir welding (FSW) involved aluminium metal. Note 2:   ISO 25239‑5   does not apply to friction stir spot welding which is covered by the   ISO 18785   series. Who is   ISO 25...

Friction stir welding. Aluminium - Quality and inspection requirements

EN ISO 25239-2:2020 摩擦搅拌焊.铝.第2部分:焊缝的设计

This document specifies design requirements for friction stir weld joints. In this document, the term "aluminium" refers to aluminium and its alloys. This document does not apply to friction stir spot welding which is covered by the ISO 18785 series.

Friction stir welding - Aluminium - Part 2: Design of weld joints (ISO 25239-2:2020)

EN ISO 25239-5:2020 摩擦搅拌焊.铝.第5部分:质量和检查要求

This document specifies a method for determining the capability of a manufacturer to use the friction stir welding (FSW) process for the production of products of the specified quality. It specifies quality requirements, but does not assign those requirements to any specific product group. In this document, the term "aluminium" refers to aluminium and its alloys. This document does not apply to friction stir spot welding which is covered by the ISO 18785 series.

Friction stir welding - Aluminium - Part 5: Quality and inspection requirements (ISO 25239-5:2020)

EN ISO 25239-4:2020 摩擦搅拌焊.铝.第4部分:焊接工艺规范刚和评定

This document specifies the requirements for the specification and qualification of welding procedures for the friction stir welding (FSW) of aluminium. In this document, the term "aluminium" refers to aluminium and its alloys. This document does not apply to friction stir spot welding which is covered by the ISO 18785 series. NOTE Service requirements, materials or manufacturing conditions can require more comprehensive testing than is specified in this document.

Friction stir welding - Aluminium - Part 4: Specification and qualification of welding procedures (ISO 25239-4:2020)

ISO 25239-4:2020 摩擦搅拌焊 - 铝 - 第4部分:焊接程序的规范和鉴定

This document specifies the requirements for the specification and qualification of welding procedures for the friction stir welding (FSW) of aluminium. In this document, the term “aluminium” refers to aluminium and its alloys. This document does not apply to friction stir spot welding which is covered by the ISO 18785 series. NOTE Service requirements, materials or manufacturing conditions can require more comprehensive testing than is specified in this document.

Friction stir welding — Aluminium — Part 4: Specification and qualification of welding procedures

ISO 25239-5:2020 摩擦搅拌焊 - 铝 - 第5部分:质量和检验要求

This document specifies a method for determining the capability of a manufacturer to use the friction stir welding (FSW) process for the production of products of the specified quality. It specifies quality requirements, but does not assign those requirements to any specific product group. In this document, the term “aluminium” refers to aluminium and its alloys. This document does not apply to friction stir spot welding which is covered by the ISO 18785 series.

Friction stir welding — Aluminium — Part 5: Quality and inspection requirements

ISO 25239-2:2020 摩擦搅拌焊接 - 铝 - 第2部分:焊接接头的设计

This document specifies design requirements for friction stir weld joints. In this document, the term “aluminium” refers to aluminium and its alloys. This document does not apply to friction stir spot welding which is covered by the ISO 18785 series.

Friction stir welding — Aluminium — Part 2: Design of weld joints

ASTM F3372-20 PA12管和配件的热熔对接接头的标准实施规程

1.1 This practice describes procedures for making butt fusion joints with Polyamide 12 (PA12) pipe and fittings by means of heat fusion joining in, but not limited to, a field environment. Procedure A is for environmental temperatures of 40 °F (4 °C) and higher. Procedure B is for site temperatures below 40 °F (4 °C). Other suitable heat fusion joining procedures are available from various sources including pipe and fitting manufacturers. This standard does not purport to address all possible heat fusion joining procedures, or to preclude the use of qualified procedures developed by other parties that have been proved to produce reliable heat fusion joints. 1.2 The parameters and procedures are applicable only to joining PA12 pipe and fittings and are not applicable to other polyamide types. They are intended only for PA12 fuel gas pipe per Specification F2785 and PA12 butt heat fusion fittings in accordance with Specification F1733. Fusion to other polyamide types (that is, cross-fusion) is not permitted under this practice, and this practice does not not apply to other polyamide types. Consult with the pipe and fittings manufacturers to make sure they recommend this procedure for the pipe and fittings to be joined (also see Appendix X1). 1.3 The procedures in this practice apply to the butt fusion of PA12 pipe and butt fusion fittings in accordance with 1.2 having like diameter and wall thickness. NOTE 1—Refer to X1.5 for guidance regarding dissimilar wall thicknesses. 1.4 Other suitable heat joining procedures are available from various sources including pipe and fitting manufacturers. Melt characteristics, average molecular weight and molecular weight distribution of PA12 compounds are influential factors in establishing suitable fusion parameters; therefore, consider the manufacturer’s recommendations in the use or development of a specific fusion procedure. 1.5 The text of this practice references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the practice. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6.1 Non-conformance with this specification is possible if values from the two systems are combined. Values in parentheses are conversions that are appropriately rounded for accuracy and precision; that are not exact equivalents, and that are for non-mandatory informational purposes. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Butt Fusion Joining of PA12 Pipe and Fittings

KS B ISO 14344:2019 焊接耗材 - 填充材料和焊剂的采购

Welding consumables — Procurement of filler materials and fluxes

KS B ISO 14327-2019 电阻焊.电阻点焊 凸焊和缝焊可焊性凸角的测定程序

Resistance welding — Procedures for determining the weldablity lobe for resistance spot, projection and seam welding

KS B 0520-2019 镍和镍合金复合钢焊接工艺鉴定试验方法

Method of welding procedure qualification test for nickel and nickel alloy clad steels

KS B ISO 14344-2019 焊接耗材 - 填充材料和焊剂的采购

Welding consumables — Procurement of filler materials and fluxes

KS B 0512-2019 耗材喷头电渣焊的推荐做法

Recommended practice for consumable nozzle electroslag welding

KS B ISO 14327:2019 电阻焊.电阻点焊 凸焊和缝焊可焊性凸角的测定程序

Resistance welding — Procedures for determining the weldablity lobe for resistance spot, projection and seam welding

KS B ISO 9692-3:2019 焊接和相关工艺 - 接头制备类型 - 第3部分:铝及其合金的金属惰性气体焊接和钨惰性气体焊接

Welding and allied processes — Types of joint preparation — Part 3: Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys