25.160.10 焊接工艺 标准查询与下载

EN 1011-8:2018 焊接.金属材料焊接的推荐规范.第8部分:铸铁焊接

Welding - Recommendations for welding of metallic materials - Part 8: Welding of cast irons

DIN EN ISO 13916:2018 焊接.预热温度、道间温度和预热维持温度的测量(ISO 13916-2017);德文版本EN ISO 13916-2017

The document specifies requirements for the measurement of preheating temperature, interpass temperature and preheat maintenance temperature for fusion welding. The document may also be applied as appropriate in the case of other welding processes. The document does not cover the measurement of post weld heat treatment temperatures.

Welding - Measurement of preheating temperature, interpass temperature and preheat maintenance temperature (ISO 13916:2017); German version EN ISO 13916:2017

EN ISO 15011-4:2018 焊接和相关工艺的卫生和安全.烟尘和气体取样的实验室方法.第4部分:烟尘数据单

Health and safety in welding and allied processes ? Laboratory method for sampling fume and gases ? Part 4: Fume data sheets

BS EN ISO 13916:2017 焊接.预热温度、道间温度和预热维持温度的测量

Welding. Measurement of preheating temperature, interpass temperature and preheat maintenance temperature

EN ISO 13918:2018 焊接.电弧螺柱焊接用螺柱和陶瓷套圈

Welding - Studs and ceramic ferrules for arc stud welding

DL/T 1762-2017 钢管塔焊接技术导则

Guidelines for Welding Technology of Steel Tube Tower

JB/T 13354-2017 动载钢结构焊接规范

Code for welding of dynamically loaded steel structures

DIN ISO 16338:2017 航空航天应用使用焊接.电阻电焊和电阻缝焊(ISO 16338-2017)

This document specifies requirements for resistance spot and seam welding for aerospace applications.

Welding for aerospace applications - Resistance spot and seam welding (ISO 16338:2017)

ISO 13916:2017 焊接.预热温度、道间温度和预热维持温度的测量

This document specifies requirements for the measurement of preheating temperature, interpass temperature and preheat maintenance temperature for fusion welding. This document can also be applied as appropriate in the case of other welding processes. This document does not cover the measurement of post weld heat treatment temperatures.

Welding - Measurement of preheating temperature, interpass temperature and preheat maintenance temperature

NB/T 47018.4-2017 承压设备用焊接材料订货技术条件 第4部分:埋弧焊钢焊丝和焊剂

NB/T 47018的本部分规定了承压设备用埋弧焊钢焊丝和焊剂的技术条件。 本部分适用于承压设备埋弧焊用碳钢焊丝和焊剂、低合金钢焊丝和焊剂、不锈钢焊丝和焊。

Technical permission of welding materials for pressure equipment.Section 4:Electrodes and fluxes for submerged arc welding

NB/T 47018.3-2017 承压设备用焊接材料订货技术条件 第3部分:气体保护电弧焊丝和填充丝

NB/T 47018的本部分规定了承压设备用气体保护电弧焊用钢焊丝和填充丝的技术条件。 本部分适用于承压设备用气体保护电弧焊用钢焊丝和填充丝、低合金钢焊丝和填充丝。

Technical permission of welding materials for pressure equipment.Section 3:Steel electrodes and rods for gas shielded arc welding

BS EN ISO 14555:2017 焊接.金属材料的电弧螺栓焊

Welding. Arc stud welding of metallic materials

BS EN ISO 15614-1:2017 金属材料焊接规程的规范和鉴定.焊接试验规程.钢的电弧焊和气焊及镍和镍合金的电弧焊

Specification and qualification of welding procedures for metallic materials. Welding procedure test. Arc and gas welding of steels and arc welding of nickel and nickel alloys

EN ISO 14555:2017 焊接.金属材料的电弧螺柱焊接

Welding - Arc stud welding of metallic materials

EN ISO 15614-1:2017 金属材料焊接程序的规范和鉴定.焊接程序试验.第1部分:钢的电弧焊和气焊及镍和镍合金的焊接

Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys

ISO 15614-1:2017 金属材料焊接程序的规范和鉴定.焊接程序试验.第1部分:钢的电弧焊和气焊及镍和镍合金的电弧焊

Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys

ASTM A488/A488M-17 钢铸件标准实践 焊接 程序和人员资格

1.1 This practice covers the qualification of procedures, welders, and operators for the fabrication and repair of steel castings by electric arc welding. 1.1.1 Qualifications of a procedure and either or both the operator or welder under Section IX of the ASME Boiler and Pressure Vessel Code shall automatically qualify the procedure and either or both the operator or welder under this practice. P-number designations in the ASME grouping of base metals for qualification may be different than the category numbers listed in Table 1. Refer to Appendix X1 for a comparison of ASTM category numbers with the corresponding ASME P-Number designations. 1.2 Each manufacturer or contractor is responsible for the welding done by his organization and shall conduct the tests required to qualify his welding procedures, welders, and operators. 1.3 Each manufacturer or contractor shall maintain a record of welding procedure qualification tests (Fig. 1), welder or operator performance qualification tests (Fig. 2), and welding procedure specification (Fig. 3), which shall be made available to the purchaser’s representative on request. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4.1 SI Units—Within the text, the SI units are shown in brackets. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Steel Castings, Welding, Qualifications of Procedures and Personnel

ISO 14555:2017 焊接.金属材料的电弧螺栓焊

This document covers arc stud welding of metallic materials subject to static and fatigue loading. It specifies requirements that are particular to stud welding, in relation to welding knowledge, quality requirements, welding procedure specification, welding procedure qualification, qualification testing of operators and testing of production welds. This document is appropriate where it is necessary to demonstrate the capability of a manufacturer to produce welded construction of a specified quality. NOTE General quality requirements for fusion welding of metallic materials are given in ISO 3834-1, This document has been prepared in a comprehensive manner, with a view to it being used as a reference in contracts. The requirements contained within it can be adopted in full, or partially, if certain requirements are not relevant to a particular construction (see Annex B). For processing of stud welding, see Annex A.

Welding - Arc stud welding of metallic materials

DIN EN ISO 15614-7:2017 金属材料焊接程序的规范和鉴定.焊接程序试验.第7部分:覆盖焊接(ISO 15614-7-2016);德文版本EN ISO 15614-7-2016

Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 7: Overlay welding (ISO 15614-7:2016); German version EN ISO 15614-7:2016

BS 8548:2017 钢筋弧焊指南

Guidance for arc welding of reinforcing steel