25.160.10 焊接工艺 标准查询与下载

GSO ISO 18594:2016 电阻点焊、凸焊和缝焊 铝和钢材料过渡电阻的测定方法

This International Standard specifies the procedure and the experimental set-up for determining the transition resistance of a single sheet or two overlapping sheets of aluminium or steel, with or without surface treatment, and with or without surface coating.

Resistance spot-, projection- and seam-welding -- Method for determining the transition resistance on aluminium and steel material

GSO ISO 15614-8:2016 金属材料焊接工艺规范和评定焊接工艺试验 第8部分：管与管板接头的焊接

This European Standard specifies requirements for the qualification testing of welding procedures for the arc welding of tube to tube-plate joints in metallic materials by manual, partly mechanized, mechanized or automatic processes. This standard is a part of a series of standards. Details of this series are given in prEN ISO 15607, Annex A. Qualification by tube to tube-plate joint tests can be used for all joints even if they are fully loaded or only seal welded as required in application standards. In such cases, one or more special test pieces should be made to simulate the production joint in all essential features, e.g. dimensions, restraint, heat sink effects. The test should be carried out prior to and under the conditions to be used in production. This standard applies to fusion welding of metallic materials for tube to tube-plate joints with gap. This standard does not apply to tube-sheets with forged end connections with welded tubes (external/internal bore welds). For welding of tube to tube-plate joints without gap welding procedure test should be defined in the specification. For other applications and/or requirements the standard can be used if required by the specification. Repair welding should be considered in the welding procedure test.

Specification and qualification of welding procedures for metallic materials -- Welding procedure test -- Part 8: Welding of tubes to tube-plate joints

GSO ISO 15609-6:2016 金属材料焊接工艺规程和评定焊接工艺规程 第6部分：激光电弧复合焊

This part of ISO 15609 specifies requirements for the content of welding procedure specifications for laser-arc hybrid welding processes. Variables listed in this part of ISO 15609 are those influencing the quality and the properties of the welded joint. NOTE Details of ISO 15609 (all parts) are given in ISO 15607:2003, Annex A.

Specification and qualification of welding procedures for metallic materials -- Welding procedure specification -- Part 6: Laser-arc hybrid welding

GSO ISO 9692-2:2016 焊接和联合工艺 接头准备 第2部分：钢的埋弧焊

This part of ISO 9692 applies to types of joint preparation for submerged arc welding with one wire electrode (process 121 according to ISO 4063) on steel. This part of ISO 9692 covers only the welding positions PA and PB according to ISO 6947. In case PC is used, special preparation will be necessary. It applies to fully penetrated welds. For partly penetrated welds, types of joint preparation, shapes and dimensions may differ from the listed proposals if they are specified in the relevant application standard or agreed by parties concerned. If the root is welded by a different arc welding process (see ISO 4063), the joint preparation according to ISO 9692 should be taken into account.

Welding and allied processes -- Joint preparation -- Part 2: Submerged arc welding of steels

GSO ISO 15614-5:2016 金属材料焊接工艺规范和评定焊接工艺试验 第5部分：钛、锆及其合金的电弧焊

This standard is part of a series of standards, details of this series are given in prEN ISO 15607:2000, annex A. This standard specifies how a preliminary welding procedure specification is qualified by welding procedure tests. This standard defines the conditions for the execution of welding procedure tests and the range of qualification for welding procedures for all practical welding operations within the range of variables listed in clause 8. Tests shall be carried out in accordance with this standard. Additional tests may be required by application standards. This standard applies to the arc welding of titanium, zirconium and their alloys in all product forms. Arc welding is covered by the following processes in accordance with EN ISO 4063. 131 — metal inert gas welding, MIG welding 141 — tungsten inert gas welding, TIG welding 15 — plasma arc welding The principles of this standard may be applied to other fusion welding processes.

Specification and qualification of welding procedures for metallic materials -- Welding procedure test -- Part 5: Arc welding of titanium, zirconium and their alloys

GSO ISO 13469:2016 机械连接 形状配合盲铆钉和（锁定）螺栓接头 测试程序的规范和鉴定

This International Standard specifies the requirements for the testing procedures for interference-fit/form-fit blind rivet joints and lock bolt joints made of metallic and non-metallic materials. The tests required for a particular joint depend upon the performance requirements of the component/assembly and shall be established before any testing is undertaken. The term sheet as used in this International Standard includes extrusions, cast material, plastics, and fibre-reinforced plastics, e. g. carbon and glass fibre-reinforced plastics. NOTE Specific service, material, or manufacturing conditions can require more comprehensive testing than specified in this International Standard. Such tests can include macro and micro sections, fatigue, and/or endurance tests. This International Standard does not apply to civil engineering applications such as metal building and steel construction which are covered by other applicable International Standards.

Mechanical joining -- Form-fit blind rivets and (lock) bolt joints -- Specifications and qualification of testing procedures

GSO ISO 15614-4:2016 金属材料焊接工艺规范和评定焊接工艺试验 第4部分：铝铸件的精焊

This part of ISO 15614 is one of a series of standards, details of which are given in ISO 15607:2003, Annex A. It specifies how a welding procedure specification for finishing welding of aluminium castings is qualified by welding procedure tests. It does not apply to repair welding. For joint welding, ISO 15614-2 applies. Arc welding of aluminium castings is covered by the following processes as defined in ISO 4063: 131 metal inert gas welding, MIG welding; 141 tungsten inert gas arc welding; TIG welding; 15 plasma arc welding. Other fusion welding processes by agreement. Shielding gases used in these processes are: — argon ISO 14175 I1; — helium ISO 14175 I2; — argon-helium mixture ISO 14175 I3. Other shielding gases by agreement.

Specification and qualification of welding procedures for metallic materials -- Welding procedure test -- Part 4: Finishing welding of aluminium castings

GSO ISO 15614-13:2016 金属材料焊接工艺规范和评定焊接工艺试验 第13部分：镦锻（电阻对接）和闪光焊

This part of ISO 15614 specifies tests for the qualification of welding procedure specifications applicable to upset (resistance butt) welding and flash welding of metallic materials, e.g. with solid, tubular, flat or circular cross-section. Its basic principles can also be applied to other resistance welding processes when this is stated in the specification. This part of ISO 15614 defines the conditions for carrying out tests and the limits of validity of a qualified welding procedure for all the practical welding operations that it covers. The tests required to qualify the procedure for a particular component or assembly depend on the performance and quality requirements of the component or assembly, as defined in the design specification. The tests are intended to be carried out in accordance with the requirements of this part of ISO 15614, unless more severe tests are specified by the relevant application standard or specification and when these apply. NOTE Specific service, material, or manufacturing conditions can require more comprehensive testing than specified by this part of ISO 15614. Such tests can include microsections, fatigue or endurance tests, impact tests, radiographic testing, ultrasonic testing, corrosion testing and tests of components or complete welded assemblies. This part of ISO 15614 covers the following resistance welding processes, as defined in ISO 4063: — 24 flash welding, using direct current or alternating current with various movement sequences, constant flashing and pulsed flashing; — 25 resistance upset welding, using direct current or alternating current with various pressure sequences.

Specification and qualification of welding procedures for metallic materials -- Welding procedure test -- Part 13: Upset (resistance butt) and flash welding

GSO ISO 17652-4:2016 焊接 与焊接和相关工艺相关的车间底漆测试 第4部分：烟雾和气体的排放

This part of this standard specifies rating of shop primers as regards their influence on emission of fumes and gases during welding. For precaution for protection of health, safety and environment during testing, see EN ISO 17652-1.

Welding -- Test for shop primers in relation to welding and allied processes -- Part 4: Emission of fumes and gases

GSO ISO 15609-5:2016 金属材料焊接工艺规程和评定焊接工艺规程 第5部分：电阻焊

This part of ISO 15609 specifies requirements for the content of welding procedure specifications for resistance spot, seam, butt and projection welding processes. It is necessary to establish the acceptability of applying the principles of this part of ISO 15609 to other resistance and related welding processes before any qualification is undertaken. NOTE Details of ISO 15609 (all parts — for titles, see Foreword) are given in ISO 15607:2003, Annex A. Variables listed in this part of ISO 15609 are those influencing either weld dimensions (quality), weld nugget dimension, weld pattern positioning, mechanical properties or geometry of the welded joint.

Specification and qualification of welding procedures for metallic materials -- Welding procedure specification -- Part 5: Resistance welding

GSO ISO 15614-6:2016 金属材料焊接工艺规范和评定焊接工艺试验 第6部分：铜及其合金的电弧焊和气焊

This part of ISO 15614 specifies how a preliminary welding procedure specification is qualified by welding procedure tests. It applies to the arc and gas welding of copper and copper alloys in all product forms. This part of ISO 15614 defines the conditions for the execution of welding procedure tests and the range of qualification for welding procedures for all practical welding operations within the range of variables listed in Clause 9. This part of ISO 15614 is applicable to all new welding procedures. However, it does not invalidate previous welding procedure tests made to former national standards or specifications. Where additional tests have to be carried out to make the qualification technically equivalent, it is only necessary to do the additional tests on a test piece made in accordance with this part of ISO 15614. Additional tests may be required by application standards. The principles of this part of ISO 15614 may be applied to other fusion welding processes.

Specification and qualification of welding procedures for metallic materials -- Welding procedure test -- Part 6: Arc and gas welding of copper and its alloys

GSO ISO 17652-3:2016 焊接 与焊接和相关工艺相关的车间底漆测试 第3部分：热切割

This part of this European Standard specifies a test method for determination of a shop primers influence on the maximum speed usable for thermal cutting. For precaution for protection of health, safety and environment during testing, see EN ISO 17652-1.

Welding -- Test for shop primers in relation to welding and allied processes -- Part 3: Thermal cutting

GSO ISO 17652-1:2016 焊接 与焊接和相关工艺相关的车间底漆测试 第1部分：一般要求

This part of this European Standard specifies standardised conditions for an assessment of shop primers on the weldability of steel materials. The standard is intended to be used for assessment of shop primers by: — testing by the suppliers during development of new shop primers; — testing by the suppliers during production as part of a quality control scheme; — declaration of the properties of shop primers by suppliers; — use as a reference in contracts between suppliers and customers for deliveries of shop primers; — acceptance testing of shop primers by customers. The standard can also be used for comparisons between different shop primers using the welding procedure appropriate for the task, or between the different welding procedures using a specific shop primer. For guidance on application see clause 4.

Welding -- Test for shop primers in relation to welding and allied processes -- Part 1: General requirements

GSO ISO 15609-3:2016 金属材料焊接工艺规程和评定焊接工艺规程 第3部分：电子束焊

This standard specifies requirements for the content of welding procedure specifications for electron beam welding. This standard is part of a series of standards, details of this series are given in EN ISO 15607:2003, annex A. Variables listed in this standard are those influencing the quality and properties of the welded joint.

Specification and qualification of welding procedures for metallic materials -- Welding procedure specification -- Part 3: Electron beam welding

GSO ISO 15614-7:2016 金属材料焊接工艺规范和评定焊接工艺试验 第7部分：堆焊焊

This part of ISO 15614 specifies how a preliminary welding procedure specification for overlay welding is qualified by welding procedure tests. This part of ISO 15614 defines the conditions for carrying out welding procedure tests and the range of qualification for welding procedures for all practical welding operations within the range of variables listed in Clause 8. Additional tests may be required by application standards. This part of ISO 15614 applies to all welding processes suitable for overlay welding. This part of ISO 15614 is applicable to all new welding procedures. However, it does not invalidate previous welding procedure tests made to former national standards or specifications. Where additional tests are carried out to make the qualification technically equivalent, they are only done on a test piece made in accordance with this part of ISO 15614. This part of ISO 15614 does not apply to overlay welding where cracks are intentionally produced (e.g. special hardfacing applications).

Specification and qualification of welding procedures for metallic materials -- Welding procedure test -- Part 7: Overlay welding

GSO ISO 9692-3:2016 焊接和相关工艺 接头准备的建议 第3部分：铝及其合金的金属惰性气体保护焊和钨极惰性气体保护焊

This part of ISO 9692 specifies types of joint preparation for metal inert gas welding, MIG, (131) and tungsten inert gas welding, TIG, (141) on aluminium and its alloys. It applies to fully penetrated welds.

Welding and allied processes -- Recommendations for joint preparation -- Part 3: Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys

KS B 0885-2016 手工焊接技术的标准评定程序

Standard qualification procedure for manual welding technique

KS B ISO 15614-4:2016 金属材料焊接程序的规范和鉴定 焊接过程试验 第4部分：铝铸件的精工焊接

Specification and qualification of welding procedures for metallic materials－Welding procedure test－Part 4：Finishing welding of aluminium castings

KS B 0546-2016 焊接环境气体浓度测量方法

Methods of mesurement for gas Concentration in welding environment

KS B ISO 15612:2016 金属材料焊接程序的规范和资格 通过采用标准焊接程序的资格

Specification and qualification of welding procedures for metallic materials－Qualification by adoption of a standard welding procedure