25.160.20 焊接消耗品 标准查询与下载
共找到 1682 条与 焊接消耗品 相关的标准，共 113 页
This document specifies the preparation of butt weld test pieces and specimens. The test pieces and specimens are used to determine the strength and impact properties of welded joints when testing welding consumables with single-run and two-run techniques. This document is applicable to welding consumables for arc welding of steel. This document is not suitable for electro-slag or electro-gas welding.
Welding consumables - Test methods - Part 2: Preparation of single-run and two-run technique test pieces and specimens in steel (ISO 15792-2:2020)
- ICS
- 25.160.20
- CCS
- 发布
- 2020-09-16
- 实施
- 2020-12-31
This document specifies requirements for the classification of covered electrodes and deposited metal in the as-welded condition and in the post-weld heat-treated condition for manual metal arc welding of non-alloy and fine grain steels with a minimum yield strength of up to 500 MPa or a minimum tensile strength of up to 570 MPa. This document is a combined specification providing for classification utilizing a system based on the yield strength and the average impact energy of 47 J of all-weld metal, or utilizing a system based on the tensile strength and the average impact energy of 27 J of all-weld metal. a) Clauses, subclauses and tables which carry the suffix letter "A" are applicable only to covered electrodes classified to the system based on the yield strength and the average impact energy of 47 J of all weld metal in this document. b) Clauses, subclauses and tables which carry the suffix letter "B" are applicable only to covered electrodes classified to the system based on the tensile strength and the average impact energy of 27 J of all weld metal in this document. c) Clauses, subclauses and tables which do not have either the suffix letter "A" or the suffix letter "B" are applicable to all covered electrodes classified in this document.
Welding consumables - Covered electrodes for manual metal arc welding of non-alloy and fine grain steels - Classification (ISO 2560:2020)
- ICS
- 25.160.20
- CCS
- 发布
- 2020-09-16
- 实施
- 2020-12-31
This document specifies the procedure to be used for deposition of a weld metal pad for chemical analysis. This document applies to deposition of a weld metal pad by use of covered electrodes, wire electrodes for gas shielded metal arc welding, tubular cored electrodes for gas shielded metal arc welding and for non-gas shielded metal arc welding, solid rods and tubular cored rods for gas tungsten arc welding, and wire-flux and strip-flux combinations for submerged arc welding or electroslag welding and cladding. This document is applicable to welding consumables for non-alloy and fine grain steels, high strength steels, creep-resisting steels, stainless and heat-resisting steels, nickel and nickel alloys, and copper and copper alloys.
Welding consumables - Deposition of a weld metal pad for chemical analysis (ISO 6847:2020)
- ICS
- 25.160.20
- CCS
- 发布
- 2020-09-16
- 实施
- 2020-12-31
This document specifies requirements for classification of wire electrodes and weld deposits in the as-welded condition and in the post-weld heat-treated condition for gas shielded metal arc welding of non alloy and fine grain steels with a minimum yield strength of up to 500 MPa or a minimum tensile strength of up to 570 MPa. One wire electrode can be tested and classified with different shielding gases. This document constitutes a combined specification providing classification utilizing a system based upon the yield strength and the average impact energy of 47 J of all-weld metal, or utilizing a system based upon the tensile strength and the average impact energy of 27 J of all-weld metal. a) Clauses and tables which carry the suffix letter "A" are applicable only to wire electrodes classified to the system based on the yield strength and the average impact energy of 47 J of all-weld metal in accordance with this document. b) Clauses and tables which carry the suffix letter "B" are applicable only to wire electrodes classified to the system based on the tensile strength and the average impact energy of 27 J of all-weld metal in accordance with this document. c) Clauses and tables which have neither the suffix letter "A" nor the suffix letter "B" are applicable to all wire electrodes classified in accordance with this document.
Welding consumables - Wire electrodes and weld deposits for gas shielded metal arc welding of non alloy and fine grain steels - Classification (ISO 14341:2020)
- ICS
- 25.160.20
- CCS
- 发布
- 2020-09-16
- 实施
- 2020-12-31
This document specifies the preparation of test pieces and specimens for all-weld metal tests in steel, nickel and nickel alloys. The test pieces and specimens are used to determine the mechanical properties of all-weld metal where required by consumable classification standards or for other purposes, in arc welding of steel, nickel and nickel alloys. This document is not applicable to single- or two-run welding or fillet welding. For these cases, ISO 15792‑2 and ISO 15792‑3 apply.
Welding consumables - Test methods - Part 1: Preparation of all-weld metal test pieces and specimens in steel, nickel and nickel alloys (ISO 15792-1:2020)
- ICS
- 25.160.20
- CCS
- 发布
- 2020-09-16
- 实施
- 2020-12-31
This document specifies requirements for the classification of solid wire electrodes, solid wires and rods for fusion welding of titanium and titanium alloys. The classification is based on their chemical composition. The compositions of solid wire electrodes for metal inert gas (MIG) welding are the same as solid wire electrodes, solid wires and rods for tungsten inert gas (TIG) arc welding, plasma arc welding, laser beam welding, and other fusion welding processes.
Welding consumables - Solid wire electrodes, solid wires and rods for fusion welding of titanium and titanium alloys - Classification (ISO 24034:2020)
- ICS
- 25.160.20
- CCS
- 发布
- 2020-08-26
- 实施
- 2020-11-30
This document specifies requirements for the classification of covered electrodes and deposited metal in the as-welded condition and in the post-weld heat-treated condition for manual metal arc welding of non-alloy and fine grain steels with a minimum yield strength of up to 500 MPa or a minimum tensile strength of up to 570 MPa. This document is a combined specification providing for classification utilizing a system based on the yield strength and the average impact energy of 47 J of all-weld metal, or utilizing a system based on the tensile strength and the average impact energy of 27 J of all-weld metal. a) Clauses, subclauses and tables which carry the suffix letter “A” are applicable only to covered electrodes classified to the system based on the yield strength and the average impact energy of 47 J of all weld metal in this document. b) Clauses, subclauses and tables which carry the suffix letter “B” are applicable only to covered electrodes classified to the system based on the tensile strength and the average impact energy of 27 J of all weld metal in this document. c) Clauses, subclauses and tables which do not have either the suffix letter “A” or the suffix letter “B” are applicable to all covered electrodes classified in this document.
Welding consumables — Covered electrodes for manual metal arc welding of non-alloy and fine grain steels — Classification
- ICS
- 25.160.20
- CCS
- 发布
- 2020-08-21
- 实施
This document specifies the procedure to be used for deposition of a weld metal pad for chemical analysis. This document applies to deposition of a weld metal pad by use of covered electrodes, wire electrodes for gas shielded metal arc welding, tubular cored electrodes for gas shielded metal arc welding and for non-gas shielded metal arc welding, solid rods and tubular cored rods for gas tungsten arc welding, and wire-flux and strip-flux combinations for submerged arc welding or electroslag welding and cladding. This document is applicable to welding consumables for non-alloy and fine grain steels, high strength steels, creep-resisting steels, stainless and heat-resisting steels, nickel and nickel alloys, and copper and copper alloys.
Welding consumables — Deposition of a weld metal pad for chemical analysis
- ICS
- 25.160.20
- CCS
- 发布
- 2020-08-21
- 实施
This document specifies requirements for classification of wire electrodes and weld deposits in the as-welded condition and in the post-weld heat-treated condition for gas shielded metal arc welding of non alloy and fine grain steels with a minimum yield strength of up to 500 MPa or a minimum tensile strength of up to 570 MPa. One wire electrode can be tested and classified with different shielding gases. This document constitutes a combined specification providing classification utilizing a system based upon the yield strength and the average impact energy of 47 J of all-weld metal, or utilizing a system based upon the tensile strength and the average impact energy of 27 J of all-weld metal. a) Clauses and tables which carry the suffix letter “A” are applicable only to wire electrodes classified to the system based on the yield strength and the average impact energy of 47 J of all-weld metal in accordance with this document. b) Clauses and tables which carry the suffix letter “B” are applicable only to wire electrodes classified to the system based on the tensile strength and the average impact energy of 27 J of all-weld metal in accordance with this document. c) Clauses and tables which have neither the suffix letter “A” nor the suffix letter “B” are applicable to all wire electrodes classified in accordance with this document.
Welding consumables — Wire electrodes and weld deposits for gas shielded metal arc welding of non alloy and fine grain steels — Classification
- ICS
- 25.160.20
- CCS
- 发布
- 2020-08-21
- 实施
This document specifies the preparation of test pieces and specimens for all-weld metal tests in steel, nickel and nickel alloys. The test pieces and specimens are used to determine the mechanical properties of all-weld metal where required by consumable classification standards or for other purposes, in arc welding of steel, nickel and nickel alloys. This document is not applicable to single- or two-run welding or fillet welding. For these cases,
Welding consumables — Test methods — Part 1: Preparation of all-weld metal test pieces and specimens in steel, nickel and nickel alloys
- ICS
- 25.160.20
- CCS
- 发布
- 2020-08-20
- 实施
This document specifies the preparation of butt weld test pieces and specimens. The test pieces and specimens are used to determine the strength and impact properties of welded joints when testing welding consumables with single-run and two-run techniques. This document is applicable to welding consumables for arc welding of steel. This document is not suitable for electro-slag or electro-gas welding.
Welding consumables — Test methods — Part 2: Preparation of single-run and two-run technique test pieces and specimens in steel
- ICS
- 25.160.20
- CCS
- 发布
- 2020-08-20
- 实施
This document provides a Japanese grouping system for materials for welding purposes, classified in accordance with the grouping system of ISO/TR 15608. It can also apply for other purposes, such as heat treatment, forming, and non-destructive testing. Types of steels are listed in accordance with the grouping system of ISO/TR 15608:2017, Table 1. Types of aluminium and aluminium alloys are listed in accordance with the grouping system of ISO/TR 15608:2017, Table 2. Types of titanium and titanium alloys are listed in accordance with the grouping system of ISO/TR 15608:2017, Table 5. This document covers grouping systems for the following standardized materials: — steels; — aluminium and its alloys; — titanium and its alloys.
Welding - Grouping systems for materials - Japanese materials (ISO/TR 20174:2020)
- ICS
- 25.160.20
- CCS
- 发布
- 2020-07-08
- 实施
This document specifies requirements for the classification of solid wire electrodes, solid wires and rods for fusion welding of titanium and titanium alloys. The classification is based on their chemical composition. The compositions of solid wire electrodes for metal inert gas (MIG) welding are the same as solid wire electrodes, solid wires and rods for tungsten inert gas (TIG) arc welding, plasma arc welding, laser beam welding, and other fusion welding processes.
Welding consumables — Solid wires and rods for fusion welding of titanium and titanium alloys — Classification
- ICS
- 25.160.20
- CCS
- 发布
- 2020-07-08
- 实施
- 0000-00-00
本标准规定了轨道交通用铝合金焊丝的产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本标准适用于轨道交通用铝合金焊丝（以下简称焊丝）。
Aluminum alloy welding wires and rods for railway application
- ICS
- 25.160.20
- CCS
- C334
- 发布
- 2020-06-30
- 实施
- 2020-07-28
本标准规定了ERNiCrFe镍基焊丝的尺寸、外形、重量及允许偏差、技术要求、试验方法、检验 规则、包装、标志和质量证明书等要求。
ERNiCrFe-7G nickel-based welding wire for gas tungsten arc welding
- ICS
- 25.160.20
- CCS
- C314
- 发布
- 2020-06-29
- 实施
- 2021-03-31
Welding — Grouping systems for materials — Japanese materials
- ICS
- 25.160.20
- CCS
- 发布
- 2020-06-19
- 实施
What is ISO 9455 ‑ 3 about? ISO 9455 ‑ 3 is the third element of the multi-series international standard that covers the soft soldering fluxes . ISO 9455 ‑ 3 gives technical specifications such as terms, definitions, method A i.e., potentiometric titration method, method B i.e., titration method with visual endpoint, precision as well as stating test report. It specifies these two methods for the determination of the acid value of a flux of types 1 and 2 only. Method A is a potentiometric titration method and is to be considered as the reference method. Method B is an alternative, visual end ‑ point, titration method. Who is ISO 9455 ‑ 3 for?...
Soft soldering fluxes. Test methods - Determination of acid value, potentiometric and visual titration methods
- ICS
- 25.160.20
- CCS
- 发布
- 2020-05-31
- 实施
- 2020-05-31
Welding consumables — Technical delivery conditions for filler materials and fluxes — Type of product, dimensions, tolerances and markings
- ICS
- 25.160.20
- CCS
- 发布
- 2020-02-13
- 实施
Welding consumables — Technical delivery conditions for filler materials and fluxes — Type of product, dimensions, tolerances and markings
- ICS
- 25.160.20
- CCS
- 发布
- 2020-02-13
- 实施
Welding consumables — Wire electrodes and weld deposits for gas shielded metal arc welding of non alloy and fine grain steels — Classification
- ICS
- 25.160.20
- CCS
- 发布
- 2019-12-31
- 实施
