25.220.99 标准查询与下载

VDI 2840-2005 碳膜-基础知识、涂层类型和性能

The subject of the present VDI guideline is carbon films which are deposited by the vacuum deposition method (PVD or CVD). These modern coating systems extend from extremely hard diamond films at one end of the scale, passing through a wide variety of mostly hydrogenated amorphous carbon films before reaching soft graphite films at the other end. This guideline pursues two aims: firstly, it should provide a uniform classification and nomenclature for carbon films; secondly, it should enable the prospective user of coated workpieces to make a preliminary selection of suitable carbon film types. Essentially this guideline deals with those coatings which are produced on an industrial scale. This means we must, for example, exclude a-C:X and ta- C:X films (X = Si, O, F, N, B, and so on) which are yet under industrial development or which currently have only a very limited application.

"Carbon films - Basic knowledge, coating types and properties"

ASTM B940-05(2014) 在锌和镉表面非铬酸涂层试验的标准实施规程

4.1 This practice is applicable to non-chromate coatings that are colorless, colored, electrochemically applied or non-electrochemically applied. The zinc or cadmium, or both, may be electrodeposited, mechanically deposited, hot-dipped, rolled, or in the form of castings. 4.2 Because of variables inherent in the salt-spray test which may differ from one test cabinet to another, interpretation of test results for compliance with expected performance should be specified by the purchaser. 4.3 Properties such as thickness, color, luster, and ability to provide good paint adhesion are not covered in this practice, nor are the chemical composition and the method of application of these finishes. 1.1 This practice covers a procedure for evaluating the protective value of chemical and electrochemical conversion coatings produced by non-chromate (chromate being defined as a compound that has chromium in the plus six oxidation state, and as such, chromium compounds in other oxidation states, such as plus three, shall not be excluded) treatments of zinc and cadmium surfaces. 1.2 The protective value of a non-chromate coating is usually determined by salt-spray test and by determining whether or not the coating possesses adequate abrasion resistance when applied for that purpose. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Testing Non-Chromate Coatings on Zinc and Cadmium Surfaces

CNS 14810-2004 管线被覆缺陷(针孔)测定法

1.1本标准规定管线被覆缺陷测定之仪器及程序。1.2 方法A在使用自来水及小于100伏特的直流电压下，适用于检测被覆膜厚为0.0254mm至0.254mm(1到10mils)薄膜被覆的针孔及孔洞。若在水中加入湿润剂则有效的检测被覆膜厚可达0.508mm(20mils)。但此法不能用来检测被覆膜的薄点，甚

Methods of test for holiday detection in pipeline coatings

AS/NZS 4158:2003 水行业用阀门及配件上的热粘结聚合物涂层

Thermal-bonded polymeric coatings on valves and fittings for water industry purposes

AS/NZS 3862:2002 钢管用外部熔接环氧涂层

Provides purchasers and manufacturers of steel pipes with a specification for external fusion-bonded epoxy coating of steel pipes for protection against corrosion.

External fusion-bonded epoxy coating for steel pipes

VDI 3824 Blatt 1-2002 PVD 和 CVD 硬质涂层 质量保证 硬质涂层的特性和应用领域

Purpose of the guideline is to allocate the most important hard-coating systems of current industrial practice to their essential fields of application, and to describe their different characteristics. Generalisations, which are intended, will, of course, have to be verified in each individual case.

PVD and CVD hard coatings - Quality assurance - Characteristic profiles and fields of application of hard coatings

SANS 3892:2000 金属材料上的转化涂层．单位面积涂层质量的测定．重量分析法

Specifies gravimetric methods for determining the coating mass per unit area of conversion coatings on metallic materials.

Conversion coatings on metallic materials - Determination of coating mass per unit area - Gravimetric methods

DIN EN ISO 3892:2001 金属材料转化涂层.单位面积涂层质量测定.称重法

The document specifies gravimetric methods for determining the coating mass per unit area of conversion coatings on metallic materials.

Conversion coatings on metallic materials - Determination of coating mass per unit area - Gravimetric methods (ISO 3892:2000); German version EN ISO 3892:2001

DIN EN 12476:2001 金属的磷酸盐转化涂层.规定要求的方法

The document specifies a method of specifying requirements for phosphate conversion coatings, intended primarily for application to ferrous metals, aluminium, zinc, cadmium and their alloys (see annex A).

Phosphate conversion coatings of metals - Method of specifying requirements; German version EN 12476:2000

VDI 3824 Blatt 4-2001 PVD和CVD硬质涂层的质量保证-硬质涂层的检验计划

Manufacturers and users are given an overview of the procedures for testing and checking basic properties of hard-coated parts. The document specifies procedures appropiate for testing specific properties. The execution and the evaluation of these procedures are described, including information on special features and problems that may be encountered in applying the respective procedure. The testing of optical, decorative, electrical, and other functional coatings which do not serve to protect from wearing or to reduce friction, is expressly excluded from the scope of this guideline.

Quality assurance of PVD and CVD hard coating - Inspection planning of hard coatings

BS EN ISO 3892:2001 金属材料的转化覆层.单位面积覆层质量的测定.重量法

This International Standard specifies gravimetric methods for determining the coating mass per unit area of conversion coatings on metallic materials. The methods are applicable to — phosphate coatings on iron and steel; — phosphate coatings on zinc and cadmium; — phosphate coatings on aluminium and its alloys; — chromate coatings on zinc and cadmium; — chromate coatings on aluminium and its alloys. The methods are applicable only to conversion coatings that are free from any supplementary coating such as oil, water or solvent-based polymers, or wax. The methods do not indicate the presence of bare spots or sites with thicknesses lower than the specified minimum in the measuring areas. In addition, the single values obtained from each measuring area is the mean thicknesses over that area. There can be no further mathematical analysis of this single value, e.g. for statistical control purposes.

Conversion coatings on metallic materials - Determination of coating mass per unit area - Gravimetric methods

EN ISO 3892:2001 金属材料的转化涂层.单位面积涂层质量的测定.重量分析法ISO 3892-2000

Conversion Coatings on Metallic Materials - Determination of Coating Mass Per Unit Area - Gravimetric Methods ISO 3892:2000

LST EN 12476-2001 金属磷酸盐转化膜 规定要求的方法

Phosphate conversion coatings of metals - Method of specifying requirements

ASTM B177-01 工程用钢表面镀铬

1.1 This guide provides information about the deposition of chromium on steel for engineering uses. This is sometimes called "functional" or "hard" chromium and is usually applied directly to the basis metal and is usually thicker than decorative deposits.1.2 This guide is not intended as a standardized procedure, but as a guide for obtaining smooth, adherent coatings of chromium of a desired thickness while retaining the required physical and mechanical properties of the base metals. Specified chromium electrodeposits on ferrous surfaces are defined in Specification B 650. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Engineering Chromium Electroplating

JG/T 133-2000 建筑用铝型材、铝板氟碳涂层

本标准规定了建筑铝型材、铝板氟碳涂层的技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于氟碳喷涂工艺的建筑用铝型材、铝板氟碳涂层。

Fluorocarbon coatings on architectural aluminum extrusions and panels

BS EN 12476:2000 金属的磷酸盐转化涂覆.规定要求的方法

This European Standard specifies a method of specifying requirements for phosphate conversion coatings, intended primarily for application to ferrous metals, aluminium, zinc, cadmium and their alloys (see annex A).

Phosphate conversion coatings of metals - Method of specifying requirements

ISO 3892:2000 金属材料上的转化膜 单位面积膜层质量的测定 重量法

This International Standard specifies gravimetric methods for determining the coating mass per unit area of conversion coatings on metallic materials. The methods are applicable to — phosphate coatings on iron and steel; — phosphate coatings on zinc and cadmium; — phosphate coatings on aluminium and its alloys; — chromate coatings on zinc and cadmium; — chromate coatings on aluminium and its alloys. The methods are applicable only to conversion coatings that are free from any supplementary coating such as oil, water or solvent-based polymers, or wax. The methods do not indicate the presence of bare spots or sites with thicknesses lower than the specified minimum in the measuring areas. In addition, the single values obtained from each measuring area is the mean thicknesses over that area. There can be no further mathematical analysis of this single value, e.g. for statistical control purposes.

Conversion coatings on metallic materials - Determination of coating mass per unit area - Gravimetric methods

EN 12476:2000 金属磷酸盐转化膜.制定要求的方法

This European Standard specifies a method of specifying requirements for phosphate conversion coatings,intended primarily for application to ferrous metals,aluminium,zinc,cadmium and their alloys(see annex A);

Phosphate Conversion Coatings of Metals - Method of Specifying Requirements

CAN/CGSB-1.300-2000 金属办公家具半光烤漆应用涂料体系

1. SCOPE 1.1 This standard applies to a factory-applied coating system (liquid and/or powdered coating) of semigloss baked finish for metal office furniture including desks, run-offs, credenzas, filing cabinets, card files, modular shelving, costumers, waste baskets and related office equipment. 1.2 This standard does not cover maintenance refinishing or old metal furniture. 1.3 The testing and evaluation of a product against this standard may require the use of materials and/or equipment that could be hazardous. This document does not purport to address all the safety aspects associated with its use. Anyone using this standard has the responsibility to consult the appropriate authorities and to establish appropriate health and safety practices in conjunction with any applicable regulatory requirements prior to its use.

Applied Coating System of Semigloss Baked Finish for Metal Office Furniture

CAN/CGSB-1.2-1998 熟亚麻籽油

1. OBJET 1.1 La présente norme s'applique à l'huile de lin cuite, obtenue à partir de l'huile de lin brute traitée thermiquement ou avec des siccatifs appropriés. 1.2 L'huile de lin cuite peut être utilisée dans la fabrication de peintures primaires, de vernis, de mastics et d'autres revêtements de protection. Elle peut aussi servir à des usages particuliers, notamment pour lubrifier des chaînes d'ancres pour empêcher la corrosion. 1.3 La mise à l'essai et l'évaluation d'un produit en regard de la présente norme peuvent nécessiter l'emploi de matériaux ou d'équipement susceptibles d'être dangereux. Le présent document n'entend pas traiter de tous les aspects liés à la sécurité de son utilisation. Il appartient à l'usager de la norme de se renseigner auprès des autorités compétentes et d'adopter des pratiques d'hygiène et de sécurité conformes aux règlements en vigueur avant de l'utiliser.

Cooked linseed oil