29.035.01 绝缘材料综合 标准查询与下载

GSO IEC 60243-2:2015 绝缘材料的电气耐久性试验方法 第2部分：恒压试验的附加要求

This part of IEC 60243 gives requirements additional to those in IEC 60243-1 for the determination of the electric strength of solid insulating materials under direct voltage stress.

Electric strength of insulating materials - Test methods - Part 2: Additional requirements for tests using direct voltage

GSO IEC 60455-2-2:2015 不溶性聚合树脂化合物规范 第2-2部分：测试方法 电气用粉末涂料的测试方法

This standard gives methods of test for thermo-setting coating powders as defined in Subclause 3.7 of IEC Publication 455-1: Specification for Solventless Polymerisable Resinous Compounds used for Electrical Insulation, Part 1: Definitions and General Requirements. Tests are included for the material before cure and in the cured form.

Specification for solventless polymerisable resinous compounds used for electrical insulation - Part 2-2: Methods of test - Test methods for coating powders for electrical purposes

GSO IEC 60455-2:2015 由用于电气绝缘的树脂制成的反应性化合物 第2部分：测试方法

This part of IEC 60455 specifies methods of test to be used for testing resin based reactive compounds, their components and cured compounds used for electrical insulation.

Resin based reactive compounds used for electrical insulation - Part 2: Methods of test

GSO IEC 60626-2:2015 电绝缘用柔性骨料材料 第2部分：测试方法

This International Standard provides the test methods for combined flexible materials for electrical insulation. Some properties and relevant test methods, according to the perfomance requirements of IEC 60626-3, were confirmed. Other test methods are described as a supplement of guidance for further specification that could be agreed between customer and supplier to meet specific needs of the end use. Materials which conform to this specification meet established levels of performance. However, the selection of material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. SAFETY WARNING It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner.

Combined flexible materials for electrical insulation - Part 2: Methods of test

GSO IEC 60216-4-3:2015 电绝缘材料 耐热性能 第4-3部分：时效炉 多室炉

This part of IEC 60216 covers the minimum requirements for ventilated and heated multichamber ovens used for thermal endurance evaluation of electrical insulation and of any other appropriate thermal conditioning application where the use of single-chamber ovens is inappropriate. It covers ovens designed to operate over all or part of the temperature range from 20 K above ambient to 500 °C. It gives acceptance tests and in-service monitoring tests for both unloaded and loaded multichamber ovens and conditions of use.

Electrical insulating materials - Thermal endurance properties - Part 4-3: Ageing ovens - Multi-chamber ovens

GSO IEC 60455-3-5:2015 用于电绝缘的树脂基反应性化合物 第3部分：单个材料的规范 表 5：不饱和聚酯基浸渍树脂

This sheet 5 of IEC 60455-3 gives the requirements for unsaturated polyester based impregnating resins, and includes requirements for certain properties at elevated temperature. Materials which conform to this specification meet established levels of performance.However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not on this specification alone.

Resin based reactive compounds used for electrical insulation - Part 3: Specifications for individual materials - Sheet 5: Unsaturated polyester based impregnating resins

GSO IEC 60250:2015 确定介电材料在电气、音频和射频（包括公制波长）下的介电常数和介电损耗因数的推荐方法

This Recommendation applies to the procedures for determination of permittivity and dissipation factor and of quantities calculated from them, such as loss index, within the frequency range 15 Hz to 300 MHz approximately. Some of the methods described in this Recommendation can, with special precautions, be used for measurements at frequencies considerably lower or higher than the given limits. Liquids and fusible materials, as well as solid materials, can be measured by the methods described. The measured values are dependent on physical conditions such as frequency, temperature and moisture content, and in special cases, on field strength as well. In some cases, tests at voltages exceeding 1 000 V may introduce effects not related to permittivity and dielectric dissipation factor, and are not described here.

Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths

GSO IEC 60455-1:2015 用于电气绝缘的树脂基活性化合物 第1部分：定义和一般要求

This part of IEC 60455 relates to resin based reactive compounds and their components used for electrical insulation. All reactive compounds are solvent-free and may contain reactive diluents and fillers. The reactions involved in curing are polymerization and/or cross linking. This standard does not relate to reactive compounds used as coating powders. NOTE – It is intended to draw up specifications for coating powders as a separate IEC Standard having a different number. These materials may be used for a range of applications, of which common ones are shown in table 1.

Resin based reactive compounds used for electrical insulation - Part 1: Definitions and general requirements

GSO IEC 60216-4-2:2015 电绝缘材料 耐热性能 第4-2部分：耐用炉 适用温度高达 300 °C 的微型炉

This part of IEC 60216 covers minimum performance requirements for ventilated and electrically heated precision ovens for thermal endurance evaluation of electrical insulating materials and other appropriate applications. It covers ovens designed to operate over all or part of the temperature range from 20 K above room temperature up to 300 °C. Two possible methods of achieving the required performance are described: a) where the required performance is achieved by precise control of temperature in a simple single chamber oven, i.e. upgraded versions of ovens conforming to IEC 60216-4-1, and, otherwise, b) where the required performance is achieved by utilizing a second chamber (iso-box), mounted within the chamber of a single-chamber oven, the purpose of which is to reduce the magnitude of any temperature changes to an acceptable level whilst maintaining the required levels of air change and circulation. NOTE 1 Experience has shown that employment of an iso-box is an economical and practical means of meeting the requirements for a precision oven. NOTE 2 It is recommended that a precision oven rather than a standard oven is used when the expected halving interval is less than 10 K (20 kh to 10 kh) in order to increase the precision of the measured temperature index and halving interval to a reasonable level.

Electrical insulating materials - Thermal endurance properties - Part 4-2: Ageing ovens - Precision ovens for use up to 300 °C

GSO IEC 60589:2015 液体萃取测定电绝缘材料中离子杂质的试验方法

The purpose of this standard is to determine whether or not ionizable soluble organic and/or inorganic materials are present in electrical insulating materials. Their presence is confirmed by the increase in volume conductivity of the liquid extract and the test is considered to have particular significance when applied to electrical insulating materials which are to be immersed in coolants or impregnants.

Methods of test for the determination of ionic impurities in electrical insulating materials by extraction with liquids

GSO IEC 60243-1:2015 绝缘材料的电气强度试验方法 第1部分：工频试验

This part of IEC 60243 provides test methods for the determination of short-time electric strength of solid insulating materials at power frequencies between 48 Hz and 62 Hz. This standard does not cover the testing of liquids and gases, although these are specified and used as impregnates or surrounding media for the solid insulating materials being tested. NOTE Methods for the determination of breakdown voltages along the surfaces of solid insulating materials are included.

Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies

GSO IEC 60212:2015 测试介电固体之前和之后使用的标准条件

This International Standard gives the accepted conditions of exposure time, temperature, atmospheric humidity and liquid immersion for use in testing solid electrical insulating materials. The range is sufficiently wide to enable suitable conditions to be selected so that either of the primary objects, set out below as a) and b), of conditioning can be achieved. These objectives aim to obtain greater reproducibility of test results by: a) partly counteracting the variations of the properties of the material due to the past history of the test specimens (often known as "normalizing", here called preconditioning), and b) ensuring uniformity of conditions during the testing. This standard is not intended to be applied for determining the influence of exposure to certain temperatures and humidity or immersions in liquids, on the properties of a material. Procedures pertaining to the effect of an environment on a material are given in various parts of IEC 60068.

Standard conditions for use prior to and during the testing of solid electrical insulating materials

GSO IEC/TS 61244-1:2015 聚合物长期放射性老化的测定 第1部分：扩散限制氧化监测技术

This part of IEC TS 61244, which is a technical specification, reviews experimental techniques to quantitatively monitor the effects when oxygen is present during ageing of polymers in various environments including temperature, radiation or ultraviolet. Inhomogenous ageing effects caused by diffusion-limited oxidation are often encountered and provide theoretical equations to estimate their importance. These effects make it difficult to understand the ageing process and to extrapolate accelerated exposure to long-term conditions. It is widely known that mechanical properties degrade prior to electrical properties. These changes are consequences of chemical changes such as oxidation. In this technical specification, only mechanical or chemical monitoring techniques are of interest. This technical specification does not deal with electrical monitoring techniques.

Determination of long-term radiation ageing in polymers - Part 1: Techniques for monitoring diffusion-limited oxidation

GSO IEC 60811-302:2015 电缆和光缆 非金属材料的测试方法 第302部分：电气测试 23 和 100°C 下包装材料的直流电阻测量

This Part 302 of IEC 60811 gives the procedure to examine the d.c. resistivity at 23 °C and 100 °C which typically applies to filling compounds used for communication cables and optical fibre cables.

Electric and optical fibre cables - Test methods for non-metallic materials - Part 302: Electrical tests - Measurement of the d.c. resistivity at 23 °C and 100 °C of filling compounds

GSO IEC 60455-3-11:2015 电气绝缘用无溶剂可聚合树脂化合物规范 第3部分：独立材料规范 数据表 11：基于环氧树脂的粉末涂料

This sheet 11 of Part 3 of the standard contains the general and special requirements for thermosetting epoxy resin-based coating powders being applied by coating processes such as fluidized air bed,powder spraying and electrostatic coating. The base of the polymer in the composition of the three types is epoxy resin.

Specification for solventless polymerisable resinous compounds used for electrical insulation. Part 3: Specifications for individual materials. Sheet 11: Epoxy resin-based coating powders

GSO IEC 61061-1:2015 电气应用用非浸渍凝缩胶合板： 第1部分：定义、名称和一般要求

This part of IEC 61061 includes the definitions required for the understanding of all three parts of the standard, the designation of the material types and the general requirements applicable to non-impregnated densified laminated wood for electrical purposes. This specification is intended to cover only sheets and rings of nominal thicknesses between 6 mm and 100 mm, inclusive. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner.

Non-impregnated densified laminated wood for electrical purposes - Part 1: Definitions, designation and general requirements

GSO IEC 60455-3-4:2015 用于电绝缘的树脂基反应性化合物 第3部分：单个材料的规格 表 4：填充聚氨酯化合物

This part of IEC 60455 contains the requirements for filled polyurethane resinous compounds in the cured form for classes PUR-F-4 to PUR-F-8.

Resin based reactive compounds used for electrical insulation - Part 3: Specifications for individual materials - Sheet 4: Filled polyurethane compounds

GSO IEC 60811-301:2015 电缆和光缆 非金属材料的试验方法 第301部分：电气试验 23°C 下填料化合物介电常数的测量

This Part 301 of IEC 60811 gives the procedure to determine the permittivity at 23 °C which typically applies to filling compounds used for optical cables, communication cables and optical fibre cables.

Electric and optical fibre cables - Test methods for non-metallic materials - Part 301: Electrical tests - Measurement of the permittivity at 23 °C of filling compounds

GSO IEC 60216-4-1:2015 电绝缘材料 耐热性能 第4-1部分：耐用炉 单室炉

This part of IEC 60216 covers minimum requirements for ventilated and electrically heated single-chamber ovens, with or without forced gas circulation, for thermal endurance evaluation of electrical insulation. It covers ovens designed to operate over all or part of the temperature range from 20 °C above ambient to 500 °C. It gives acceptance tests and inservice monitoring tests for these ageing ovens.

Electrical insulating materials - Thermal endurance properties - Part 4-1: Ageing ovens - Single-chamber ovens

GSO IEC 60544-1:2015 电绝缘材料 电离辐射影响的测定 第1部分：辐射相互作用和剂量测定

This part of IEC 60544 deals broadly with the aspects to be considered in evaluating the effects of ionizing radiation on all types of organic insulating materials. It also provides, for Xrays, γ-rays, and electrons, a guide to – dosimetry terminology, – methods for dose measurements, – testing carried out at irradiation facilities, – evaluation and testing of material characteristics and properties, – documenting the irradiation process. Dosimetry that might be carried out at locations of use of the material is not described in this standard.

Electrical insulating materials - Determination of the effects of ionizing radiation - Part 1: Radiation interaction and dosimetry