29.035.01 绝缘材料综合 标准查询与下载

GSO IEC/TR 62422:2014 固体绝缘材料的环境性能

This technical report gives framework guidelines for collecting environmental data of insulating materials useful to engineers and designers of electrotechnical products for evaluating environmental impacts. It also provides a guideline for common format in environmental data reporting. This will enable producers to more easily evaluate the potential environmental impacts of those electrotechnical products using solid insulating materials. Moreover, it will allow a quick assessment of conformity to relevant electrotechnical productrelated environmental regulations.

Environmental characterization of solid insulating materials

GSO IEC 61212-3-1:2014 绝缘材料 用于电气用途的基于热固性树脂的刚性轧制箔管和棒 第3部分：单个材料的规格 第 1 页：圆形箔轧制管

This part of IEC 61212 gives requirements for industrial rigid round laminated rolled tubes for electrical purposes, based on different resins and different reinforcements. Applications and distinguishing properties are given in Table 1. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner.

Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: Round laminated rolled tubes

GSO IEC 61302:2014 电绝缘材料 耐级联和耐腐蚀性评价方法 滚轮跌落试验

This International Standard describes a method of test for comparing the performance of insulating materials, when they are exposed intermittently to a liquid contaminant and then to an a.c. electric stress along their su rface. It should be realized that the test was developed to compare the resistance to tracking and erosion of materials belonging to one specific family, so that comparisons between results in different families may not be fully valid. The test apparatus uses a rotating wheel on which standard' ) rod- or tube-shaped specimens, fitted with electrodes at each end, are located around the periphery of the wheel. The wheel, mounted at a small angle to the horizontal, is rotated slowly so that the test specimens are repeatedly dipped in a specified salt-water solution (contaminant) and then withdrawn. After withdrawal, the solution is allowed to drain or drip from the surface of the test specimen for a short time before a specified voltage is applied. The voltage causes electrical discharges (tiny arcs, scintillations) across dry areas which develop on the su rface of the specimens. These discharges may cause surface degradation to progress; until flashover occurs, or the leakage current exceeds a specified value 2) . The time to flashover, or to exceed the specified leakage current, and observation of the nature and severity of degradation are the criteria used to compare materials. The test conditions are such that materials suitable for use out of doors normally fail within a few thousand hours. IEC 112 and IEC 587 (see annex B) describe tests of much shorter duration, on smaller samples, to assess the ability of materials to withstand electric stress when exposed to liquid contamination on one surface. These tests may rate materials differently from tests of longer duration. Salt-fog tests (not yet standardized by IEC) are also in use. Such tests permit comparison of materials in the form in which they will be used in service. The test results are then dependent both on the materials used and the design of the test specimens. Such tests may also evaluate materials differently.

Electrical insulating materials - Method to evaluate the resistance to tracking and erosion - Rotating wheel dip test

GSO IEC 60464-1:2014 电气装置用清漆 第1部分：定义和一般要求

This part of IEC 60464 relates to varnishes used for electrical insulation. The varnishes may be used for finishing or impregnating applications, and may be dried or dried and cured at ambient or elevated temperatures.

Varnishes used for electrical insulation - Part 1: Definitions and general requirements

GSO IEC 60167:2014 测定固体绝缘材料绝缘电阻的试验方法

These methods of test cover procedures for the determination of insulation resistance without discrimination between the volume and surface resistances involved. Because the test specimens are simply and easily prepared, these methods are particularly useful for rapidly determining values which will give a general indication of quality when great accuracy is not required.

Methods of test for the determination of the insulation resistance of solid insulating materials

GSO IEC 60893-3-7:2014 绝缘材料 电气用热固性树脂工业刚性层压板 第3-7部分：单个材料的规范 基于聚酰亚胺树脂的刚性层压板的要求

Gives the requirements for industrial rigid laminated sheets for electrical purposes based on polyimide resins and different reinforcements. Applications and distinguishing properties are given. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. In this revision of the IEC 60893 series of specifications, new material types have been included, changes have been made to the property requirements of some existing types, a new method for testing permittivity and dissipation factor has been added, and all non-specification data for each type has been moved to a new Part 4 document - IEC 60893-4; Typical values.

Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3-7: Specifications for individual materials - Requirements for rigid laminated sheets based on polyimide resins

GSO IEC 60893-2:2014 电气用热固性树脂工业刚性层压板 第2部分：测试方法

This part of IEC 60893 describes methods of test for the materials defined in IEC 60893-1 (referred to also as Part 1).

Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 2: Methods of test

GSO IEC 62539:2014 电气绝缘击穿数据统计分析指南

Electrical insulation systems and materials may be tested using constant stress tests in which times to breakdown are measured for a number of test specimens, and progressive stress tests in which breakdown voltages may be measured. In either case, it will be found that a different result is obtained for each specimen and that, for given test conditions, the data obtained may be represented by a statistical distribution. This guide describes, with examples, statistical methods to analyze such data. The purpose of this guide is to define statistical methods to analyze times to breakdown and breakdown voltage data obtained from electrical testing of solid insulating materials, for purposes including characterization of the system, comparison with another insulator system, and prediction of the probability of breakdown at given times or voltages. Methods are given for analyzing complete data sets and also censored data sets in which not all the specimens broke down. The guide includes methods, with examples, for determining whether the data is a good fit to the distribution, graphical and computer-based techniques for estimating the most likely parameters of the distribution, computer-based techniques for estimating statistical confidence intervals, and techniques for comparing data sets and some case studies. The methods of analysis are fully described for the Weibull distribution. Some methods are also presented for the Gumbel and lognormal distributions. All the examples of computer-based techniques used in this guide may be downloaded from the following web site “http:// grouper.ieee.org/groups/930/IEEEGuide.xls.” Methods to ascertain the short time withstand voltage or operating voltage of an insulation system are not presented in this guide. Mathematical techniques contained in this guide may not apply directly to the estimation of equipment life.

Guide for the statistical analysis of electrical insulation breakdown data

GSO IEC/TR 62392:2014 典型电绝缘材料 (EIM) 对聚合物回收的适用性

This Technical Report gives information for the assessment of factors associated with the polymer recycling and/or reuse of typical insulating materials in electrotechnical equipment. It gives information and assistance to developers and design engineers for assessment in selecting polymers and polymer combinations, and is a contribution to the preservation of resources and the minimization of disposal costs at the end of a product life. The environmental compatibility of polymers must be assessed in the light of the function of the materials in the product and the total service life. An important aspect is the recovery of the material at the end of the product life. The value level of material recycling as recovery option can be improved by incorporation of suitability for dismantling into the design of the article and the choice of insulating materials which are generally used. This document will cover material recycling only as part of recovery.

Suitability of typical electrical insulating material (EIM) for polymer recycling

GSO IEC 60893-3-5:2014 绝缘材料 电气用热固性树脂工业刚性层压板 第3-5部分：单个材料的规范 基于聚酯树脂的刚性层压板的要求

Gives the requirements for industrial rigid laminated sheets for electrical purposes based on polyester resins and different reinforcements. Applications and distinguishing properties are given. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. In this revision of the IEC 60893 series of specifications, new material types have been included, changes have been made to the property requirements of some existing types, a new method for testing permittivity and dissipation factor has been added, and all non-specification data for each type has been moved to a new Part 4 document - IEC 60893-4: Typical values.

Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3-5: Specifications for individual materials - Requirements for rigid laminated sheets based on polyester resins

GSO IEC 60464-3-2:2014 用于电气绝缘的清漆 第3部分：各种材料的规格 表 2：热固化浸渍清漆

This sheet of IEC 60464-3 gives the requirements for hot curing impregnating varnishes and includes requirements for certain properties at elevated temperature.

Varnishes used for electrical insulation - Part 3: Specifications for individual materials - Sheet 2: Hot curing impregnating varnishes

GSO IEC 62631-1:2014 固体绝缘材料的电阻和绝缘性能 第1部分：概述

This part of IEC 62631 gives general guidelines for the determination of dielectric and resistive properties of solid electrical insulating materials.

Dielectric and resistive properties of solid insulating materials - Part 1: General

GSO IEC 60626-1:2014 电气绝缘用柔性组合材料 第1部分：定义和一般要求

This part of IEC 60626 contains the definitions related to and the general requirements to be fulfilled by combined flexible materials for electrical insulation. This standard does not include mica paper, as primary component, covered by IEC 60371, but mica paper may be used as complementary material. Materials which conform to this specification meet established levels of performance. However, the selection of material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. SAFETY WARNING It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner.

Combined flexible materials for electrical insulation - Part 1: Definitions and general requirements

KS C IEC 60684-3-201:2014 柔软绝缘套管 第3部分：各种型号套管的规范 第201节 交联聚氯乙烯、收缩率为2 1可收缩通用软套管

Flexible insulating sleeving — Part 3: Specifications for individual types of sleeving — Sheet 201: Heat-shrinkable sleeving, general, purpose, flexible, cross-linked PVC, shrink ratio 2：1

KS C IEC 60684-3-272:2014 柔软绝缘套管 第3部分：各种型号套管的规范 第271节 热缩弹性套管、火焰滞后 抗液流、收缩比2 1薄壁

Flexible insulating sleeving — Part 3: Specifications for individual types of sleeving — Sheet 272: Heat-shrinkable elastomer sleeving, flame retarded, fluid resistant, shrink ratio 2：1, thin wall

KS C IEC 60684-3-217-2014 柔性绝缘套管 - 第3部分:套管类型的规格 - 第217页:热收缩聚烯烃套管 阻燃收缩比3:1

Flexible insulating sleeving — Part 3: Specifications for individual types of sleeving — Sheet 217: Heat-shrinkable polyolefin sleeving, flame retarded, shrink ratio 3：1

KS C IEC 60684-3-272-2014 柔性绝缘套管 - 第3部分:各种类型套管的规格 - 片材272:热收缩弹性体套管 阻燃 耐流体 收缩比2:1 薄壁

Flexible insulating sleeving — Part 3: Specifications for individual types of sleeving — Sheet 272: Heat-shrinkable elastomer sleeving, flame retarded, fluid resistant, shrink ratio 2：1, thin wall

KS C IEC 60684-3-209:2014 柔软绝缘套管 第3部分：各种型号套管的规范 第209节 通用阻燃聚烯烃收缩比2 1的热收缩套管

Flexible insulating sleeving — Part 3: Specifications for individual types of sleeving — Sheet 209: Heat-shrinkable polyolefin sleeving, general purpose, flame retarded, shrink ratio 2:1

KS C IEC 60684-3-218-2014 柔性绝缘套管第3部分:套管类型的规范第218页:收缩率为3:1的非阻燃热收缩聚烯烃套管

Flexible insulating sleeving — Part 3: Specifications for individual types of sleeving — Sheet 218: Heat-shrinkable polyolefin sleeving, not flame retarded, shrink ratio 3：1

KS C IEC 60684-3-217:2014 柔软绝缘套管 第3部分：各种型号套管的规范 第217节 热缩聚烯烃套管 火焰滞后 收缩比3 1

Flexible insulating sleeving — Part 3: Specifications for individual types of sleeving — Sheet 217: Heat-shrinkable polyolefin sleeving, flame retarded, shrink ratio 3：1