29.060.01 电线和电缆综合 标准查询与下载

GOST 18690-2012 电缆、导线、软线和电缆附件.包装,标志,运输和保管

Cable, wires, cord and armature. Marking, packing, carriage and storage

JB/T 6467-2011 额定电压26/35kV及以下电力电缆附件.系列型谱

本标准规定了额定电压26/35kV及以下电力电缆附件的系列型谱。 本标准适用于额定电压26/35kV及以下电力电缆附件（以下简称电力电缆附件）的分类系列划分，并指导产品开发和应用选型。

Type pedigree on accessories for power cables with rated voltages up to 26/35kV

ANSI/UL 66-2011 灯具电线安全标准

Addition of the Aging Condition for the Flexing Test of Nylon Jacketed Types TFN and TFFN

Standard for Safety for Fixture Wire

DS/IEC/TR 62602:2010 绝缘电缆的导体 AWG 和 KCMIL 规格的数据

This Technical Report specifies the nominal cross-sectional areas, in the range 20 AWG to 2000 kcmil (0,52 to 1010 mm2S), for conductors in electric power cables and cords of a wide range of types. Requirements for numbers and sizes of wires and resistance values are also included. These conductors include solid and stranded copper, aluminium and aluminium alloy conductors in cables for fixed installations and flexible copper conductors.The Technical Report is not intended to apply to conductors designed for use in cables intended for telecommunication or data transmission, winding wires or similar products.Unless indicated to the contrary in a particular c

Conductors of insulated cables - Data for AWG and KCMIL sizes

UL 62-2010 软线和电缆

Flexibile cords and cables

CSA C22.2 No.49-2010 软电线和电缆

Scope 1.1 General This standard specifies the requirements for flexible cords, elevator cables, and hoistway cables rated 600 V maximum and intended for use in accordance with CSA C22.1, Canadian Electrical Code (CEC), Part I and CAN/CSA-C22.2 No. 0, General Requirements / Canadian Electrical Code, Part II, in Canada, NOM-001-SEDE, La Norma de Instalaciones Electricas (Mexican Electrical Code [MEC]), in Mexico, and NFPA 70, National Electrical Code (NEC), in the United States. 1.2 Products included This standard covers the following products: a) service cords; b) elevator cables; c) hoistway cables; d) heater cords; e) range and dryer cords; f) cords for decorative lighting; g) tinsel and lamp cords; and h) special use cords.

Flexible cords and cables

ANSI/UL 62a-2010 软电线和电缆安全性标准(提案日期 2009年6月26日)

Standard for Safety for Flexible Cords and Cables (Proposal dated 6/26/09)

ANSI/UL 62-2010 柔性索线和电缆用安全性标准(提案日期 6/26/09)

This standard specifies the requirements for flexible cords, elevator cables, and hoistway cables rated 600 V maximum and intended for use in accordance with CSA C22.1, Canadian Electrical Code (CEC), Part I and CAN/CSA-C22.2 No. 0, General Requirements - Canadian Electrical Code, Part II, in Canada, NOM-001-SEDE, La Norma de Instalaciones Electricas (Mexican Electrical Code [MEC]), in Mexico, and NFPA 70, National Electrical Code (NEC), in the United States.

Standard for Safety for Flexible Cords and Cables (Proposal dated 6/26/09)

ANSI/NECA 130-2010 安装和维修配线装置的标准

This standard describes the installation and maintenance procedures for wiring devices.

Standard for Installing and Maintaining Wiring Devices

ASTM A779/A779M-10 预应力混凝土用应力消除未涂覆密实七股钢丝绞绳标准规范

1.1 This specification describes three grades of compacted, seven-wire, uncoated, stress-relieved strand for use in pre-tensioned and post-tensioned prestressed concrete construction. 1.2 Supplement I describes low-relaxation strand and low-relaxation testing. 1.3 The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other, without combining values in any way.

Standard Specification for Steel Strand, Seven-Wire, Uncoated, Compacted, Stress-Relieved for Prestressed Concrete

DS/EN 62275:2009 电缆管理系统 电气装置用电缆扎带

This International Standard specifies requirements for metallic, non-metallic and composite cable ties and their associated fixing devices used for the management and support of wiring systems in electrical installations.Cable ties and associated fixing devices may also be suitable for other applications and where so used, regard should be taken of any additional requirements.This standard does not contain requirements that evaluate any electrical insulation properties of the cable tie or mechanical protection of the cables provided by the cable tie.

Cable management systems - Cable ties for electrical installations

ANSI/ICEA P-54-440-2009 在电缆托架中安装的电缆的安培容量

This Standards Publication covers the ampacity ratings for 600-15,000 volt solid dielectric cables installed in cable trays. Ampacity ratings are tabulated for single conductor cables, triplexed assemblies of single conductor cables, and three-conductor cables incorporating an overall jacket.

Ampacities of Cables Installed in Cable Trays

KS C IEC 60034-11-2008(2018) 旋转电机第11部分:热保护

Rotating electrical machines－Part 11：Thermal protection

KS C IEC 60034-11-2008(2023) 旋转电机第11部分:热保护

Rotating electrical machines－Part 11：Thermal protection

DS/CLC/TR 62125:2008 特定于 TC 20 的环境声明 电缆

IEC/TR 62125, which is a technical report, is intended to give assistance to standard-writers of IEC Technical Committee 20, to take into account the relevant environmental aspects as far as they are specific to electric cables in normal use. It also assists them to keep in mind a clear methodology when considering these aspects and when checking possible interaction of the normative requirements with the environment. Also, these guidelines assist standardwriters to avoid too simple or too stringent requirements that might not achieve a favourable global result.This technical report, by its very nature, is not prescriptive and does not limit innovation.NOTE

Environmental statement specific to TC 20 - Electric cables

JB/T 5814.8-2008 电线电缆专用设备.基本参数.第8部分:上引连铸设备

JB/T 5814的本部分规定了电线电缆铜导体上引连铸设备的系列及基本参数。 本部分适用于铜导体上引连铸设备。 本部分规定的铜导体上引连铸设备，也可用于上引连铸铜合金。

Equipments for electdc wires and cables.Basic parametem.Part 8: Upward continuous casting machines

JB/T 7600.2-2008 电线电缆PNS型机用线盘.第2部分:钢板焊接机用线盘

JB/T 7600的本部分规定了PNS型钢板焊接机用线盘材料、型号、规格、基本技术要求及检测项目。 本部分适用于最大装载负荷为70N/dm，并能在退火炉中使用的钢板焊接机用线盘。

PNS-type machine spool for processing of electric wire and cable.Part 2: Machine spool with welded steel plate

JB/T 7600.1-2008 电线电缆PNS型机用线盘第1部分:一般规定

JB/T 7600的本部分规定了PNS型机用线盘的代号、型式、材料、规格、技术要求、验收规则、检测方法和包装、标志等内容。 本部分适用于电线电缆生产过程中使用的PNS型机用线盘。

PNS-type machine spool for processing of elective wire and cable.Part1:General

JB/T 6756.10-2008 电线电缆专用设备.检测方法.第10部分:SP、SL系列挤塑设备

JB/T 6756的本部分规定了SP、SL系列挤塑设备的检测方法。 本部分适用于SP、SL系列挤塑设备。

Equipments for electric wires and cables.Testing methods.Part10:SP,SL Series plastic extruding machines

JB/T 6756.9-2008 电线电缆专用设备.检测方法.第9部分:QH系列漆包设备

JB/T 6756的本部分规定了QH系列漆包设备的检测方法。 本部分适用于QH系列漆包设备。

Equipments for electric wires and cables.Testing methods.Part9:QH Series enamelling machines