29.060.01 电线和电缆综合 标准查询与下载

JB/T 10435-2004 电缆局部放电测试系统检定方法

本标准规定了电缆局部放电测试系统的检定项目与技术要求、检定用器具、检定方法和检定结果及处理。 　　本标准适用于电缆局部放电测试系统的检定。 　　本标准适用于新制造的、修理后的和使用中的电缆局部放电测试系统的检定。

Inspection methods for partial discharge testing system of electric cables

JB/T 10438-2004 额定电压450/750V及以下交联聚氯乙烯绝缘电线和电缆

本标准规定了额定电压450/750V及以下交联聚氯乙烯绝缘电线和电缆的产品结构、技术要求、电缆的试验、验收规则、交货长度、标志和包装。 　　本标准适用于额定电压450/750V以及固定布线和电力、建筑、电子设备内部连接用铜芯交联聚氯乙烯绝缘电线和电缆。

Cross-linked polyvinyl chloride insulated wires and cables of rated voltages up to and including 450/750V

AECMA PREN 2235-2004 航空航天系列.屏蔽和护套单芯和多芯电缆技术规范

This "Aerospace Series" frestandard has been drawn up under the responsibility of AECMA-STAN (The European Association of Aerospace Industries - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments.

Aerospace series Single and multicore electrical cables, screened and jacketed Technical specification Edition P 3

ANSI/NECA 111-2003 非金属管道的安装标准(RNC、ENT和LFNC)

Describes installation procedures for nonmetallic raceways of circular cross-section used for electrical power wire and cable, communications wiring, or fiber optic cables.

Standard for Installing Nonmetallic Raceways (RNC, ENT and LFNC)

ANSI/ASTM F1883:2003 用美国线规(AWG)或米制单位选择电线和电缆规格的实施规程

This practice is intended as a guide to shipbuilders, shipowners, and design agents for use in the selection of conductor size for single conductor or multiple conductor cable sizes either in American Wire Gauge (AWG) or metric designations for commercial ship design and construction. The comparison chart of electrical conductor sizes shown in Table 1 presents a combined listing of international standard sizes of annealed copper conductors in accordance with AWG (Specification B 8) English units or IEC (IEC 228) metric units. As a precautionary caveat, some conductor sizes listed in Table 1 may exceed minimal size requirements of the U.S. Coast Guard, the American Bureau of Shipping, and IEEE STD 45 for specific applications The values stated for ampacity and dc resistance are presented as typical values and are provided for information only.

Practice for Selection of Wire and Cable Size, in AWG or Metric Units

DL/T 832-2003 光纤复合架空地线

本标准对光纤复合架空地线 (Optical fiber composite overhead ground wires，以下簡稱 OPGW) 的 产品型号、结构、技术要求、特性参数、相应的试验方法和验收规则、包装、运输贮存、安装建议以 及使用说明书进行了规范要求。 本标准适用于光纤复合架空地线 (OPGW) 。

Optical fiber composite overhead ground wires

UL 66 BULLETINS-2003 8/21/2003（16p）, 4/28/2003（50p）

This bulletin proposes revisions of UL 66 to make several corrections and to add Types PAFF and PAF.

8/21/2003 (16p), 4/28/2003 (50p)

SNI 04-6951.1-2003 电缆的电气试验方法. 第1部分：电压最高可达(含) 450-750 V 的电缆、芯线和电线的电气试验

Electrical test methods for electric cables. Part 1: Electrical tests for cables, cords and insulated wires for voltages up to 450/750 V

KS B 7364-2002(2012) 盘类型是自动级线

Cable disc conveyor for livestock feeder

UL 62-2002 绕性金属线

Fixture wire

SAE AS21004-2002 宾夕法尼亚州Warrendate地区Commonwealth Drive 400号,邮编:15096 - 0001,第1页,共3页,AS21004 1型,1类,175℃总导体温度的压接式铜制矩形簧片的未绝缘接线片FSC 5940

400 Commonwealth Drive, Warrendale, PA 15096-0001 SHEET 1 OF 3 AS21004 TERMINAL, LUG, UNINSULATED, RECTANGULAR TONGUE, CRIMP STYLE, COPPER, TYPE I, CLASS 1 FOR 175°C TOTAL CONDUCTOR TEMPERATURE FSC 5940TABLE1 - DASH NUMBERSTABLE2 - WIRE SIZETABLE3 - STYLETABLE4 - METHIC TABLE FOR MS21004D

400 Commonwealth Drive, Warrendale, PA 15096-0001 SHEET 1 OF 3 AS21004 TERMINAL, LUG, UNINSULATED, RECTANGULAR TONGUE, CRIMP STYLE, COPPER, TYPE I, CLASS 1 FOR 175°C TOTAL CONDUCTOR TEMPERATURE FSC 5940

CNS 9827-2001 花线安全电流

本标准适用于以 PVC、PE 或橡胶为绝缘之铜导体软质电线之安全电流。

Safety current of flexible cords

AECMA PREN 2234-2001 航空航天系列.耐火电缆 技术规则

This "Aerospace Series'' Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). lt is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries.

Aerospace Series Cables, Electrical, Fire Resistant Technical Specification Edition P 2

JIS C 8471-2-1:2000 电气设备的电缆线槽和导管系统.第2部分:特殊要求.第1节:固定于墙上和天花板上的电缆线槽和导管系统

この規格は，壁及び天井に取り付けることを目的とするケーブルトランキング及びダクティングシステムに関する要求事項について規定する。

Cable trunking and ducting systems for electrical installations -- Part 2: Particular requirements -- Section 1: Cable trunking and ducting systems intended for mounting on walls or ceilings

JIS C 8471-1:2000 电气设备的电缆线槽和导管系统.第1部分:一般要求

この規格は，電気設備用の電線，ケープル.コード又は他の電気機器の収容若しくは場合によっては分離のためのケープルトランキング及びケープルダクティングシステムに対する要求事項を規定する。

Cable trunking and ducting systems for electrical installations -- Part 1: General requirements

DB31/T 72-1999 工业锅炉运行检测与控制装置的配置

Equipment configuration for check-measure and control in industrial boiler function

IEC 60317-23:2000 特种绕组线规范.第13部分:180级丝包可软焊聚酰亚胺漆包圆铜线

GB/T 6109的本部分规定了以聚酯亚胺树脂为基的单一漆层180级漆包铜圆线的要求。如果能保留原树脂的化学特性并且满足该漆包线规定的所有要求， 则该树脂可以改性。 注：改性树脂是一种经过化学变化的， 或者含有一种或多种添加剂以提高其某种性能或使用特性的树脂。 180级表示特级， 它要求最小温度指数为180， 热冲击温度至少为200℃. 对应于温度指数的摄氏温度并不就是推荐的漆包线使用温度， 因为这取决于包括所用设备类型在内的很多因素。 本部分规定的导体标称直径范围为： －1级：0.020 mm 及以上1.600 mm 及以下； －2级：0.020 mm 及以上1.600 mm 及以下. 导体标称直径按GB/T 6109.1-2008中的第4章的规定。

Specifications for particular types of winding wires -Part 13:Solderable polyesteimide enamelled round copper wire,class 180

GOST R 51651-2000 电缆产品 质量体系 建筑材料

Cable products. Quality system. Construction materials

JB/T 50136.2-1999 隔爆型三相异步电动机隔爆组件.可靠性指标评定方法(试验室法)（内部使用）

本标准规定了隔爆型三相异步电动机隔爆组件的可靠性失效判据和试验方法。 本标准适用于0.55～200 kW工厂及矿用隔爆型三相异步电动机隔爆组件的可靠性指标评定。

Flame prevention unit of flameproof three-phase asynchronous motors Reliability index assessment method (laboratory method) (only for internal use)

DS/HD 361 S3:1999 电缆标识系统

This Harmonisation Document details a designation system for harmonised power cables and cords, of rated voltage up to and including 450/750 V.

System for cable designation