29.120.30 插头、插座、连接器 标准查询与下载

GSO IEC 60906-1:2015 家用和类似用途插头和插座的 IEC 系统 第1部分：插头和插座 16 A 250 V ac

This standard applies to the IEC System of plugs and socket-outlets rated 16 A 250 V a.c. for household and similar purposes for the connection of equipment to distribution systems having nominal voltages between 200 V and 250 V a.c., insofar as dimensional requirements are concerned. This standard does not apply to plugs and socket-outlets rated 15 A 125 V a.c. for household and similar purposes for the connection of equipment to distribution systems having nominal voltages between 100 V and 125 V a.c. NOTE In Spain and the UK, household use of plug and socket-outlets complying with this standard is forbidden.

IEC system of plugs and socket-outlets for household and similar purposes - Part 1: Plugs and socket-outlets 16 A 250 V a.c.

GSO IEC 62196-1:2015 插头、插座、车辆连接器和车辆入口 电动汽车充电连接器 第1部分：一般要求

This part of IEC 62196 is applicable to plugs, socket-outlets, vehicle connectors, vehicle inlets and cable assemblies for electric vehicles, herein referred to as “accessories”, intended for use in conductive charging systems which incorporate control means, with a rated operating voltage not exceeding – 690 V a.c. 50 Hz to 60 Hz, at a rated current not exceeding 250 A, – 1 500 V d.c. at a rated current not exceeding 400 A. These accessories are intended to be installed by instructed persons (IEC 60050-195:1998, IEC 60050-195/AMD1:2001, 195-04-02) or skilled persons (IEC 60050-195:1998, IEC 60050- 195/AMD1:2001, 195-04-01) only. These accessories and cable assemblies are intended to be used for circuits specified in IEC 61851-1 which operate at different voltages and frequencies and which may include extra-low voltage and communication signals. These accessories and cable assemblies are to be used at an ambient temperature between –30 °C and +50 °C. NOTE 1 In some countries, other requirements may apply. NOTE 2 the following countries, –35 °C applies: SE. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. The accessories covered by this part of IEC 62196 are for use in certain modes of charging electric vehicles. These modes are defined in IEC 61851-1. These definitions and a description of the types of connection (cases A, B and C), are described in IEC 61851-1:2010, 6.2 and 6.3.1. NOTE 3 In the following countries, mode 1 will not be allowed: UK, US, CA, SG. This part of IEC 62196 does not apply to those standardised accessories used in charging systems where the use of such accessories constructed to the requirements of other standards is permitted (e.g. in mode 1 and mode 2). Such standardized accessories may be used for those situations (mode and case) identified in IEC 61851-1. This part of IEC 62196 may be used as a guide for accessories with a lesser number of contacts and lower ratings for use with light duty vehicles

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements

GSO IEC 60309-4:2015 工业用途插头、插座和耦合器 第4部分：带或不带内部锁定的插座开关和连接器

This clause of Part 1 or Part 2 is applicable except as follows: Replacement of the first paragraph by the following text: This part of IEC 60309 applies to self-contained products that combine within a single enclosure, a socket-outlet or connector according to IEC 60309-1 or IEC 60309-2 and a switching device, with a rated operating voltage not exceeding 690 1 000 V d.c. or a.c. and 500 Hz , and a rated current not exceeding 250 800 A, primarily intended for industrial use, either indoors or outdoors. These accessories are intended to be installed by instructed persons (Amendment 1:2001 of IEC 60050-195:1998, 195-04-02) or skilled persons (Amendment 1:2001 of IEC 60050-195:1998, 195-04-01) only. These products may incorporate an interlock and/or protective devices.

Plugs, socket-outlets and couplers for industrial purposes - Part 4: Switched socket-outlets and connectors with or without interlock

EN 60320-1:2015 家用和类似通用电器连接器

Appliance couplers for household and similar general purposes Part 1: General requirements

IEC TS 62735-1:2015 数据中心和电信中心办公室中安装的信息和通信技术 (ICT) 设备的直流 (DC) 插头和插座. 第1部分: 2,6 kW的插头和插座系统

Direct current (DC) plugs and socket-outlets for information and communication technology (ICT) equipment installed in data centres and telecom central offices Part 1: Plug and socket-outlet system for 2,6 kW

IEC 60320-1:2015 家庭和类似用途器具连接器.第1部分:一般要求

This part of lEC 60320 sets the general requirements for appliance couplers for two poles and two poles with earth contact and for the connection of electrical devices for household and similar onto the mains supply. This part of lEC 60320 is also valid for appliance inlets/appliance outlets integrated or incorporated in appliances. The rated voltage does not exceed 250 V (a.c.) and the rated current does not exceed 16 A. Appliance couplers complying with this part of lEC 60320 are suitable for normal use at ambient temperatures not normally exceeding +40 °C, but their average over a period of 24 h does not exceed +35 °C, with a lower limit of the ambient air temperature of -5 °C. Appliance couplers are not suitable for use in place of plug and socket-outlet systems according to IEC 60884-1; use in place of devices for connecting luminaires (DCLs) according to IEC 61995 or luminaire supporting couplers (LSCs). NOTE Requirements for d.c. are under consideration.

Appliance couplers for household and similar general purposes - Part 1: General requirements

BS EN 60320-3:2014 家用和类似一般用途的电器耦合器 标准薄板和量规

Appliance couplers for household and similar general purposes. Standard sheets and gauges

GOST IEC 60906-2-2015 家用和类似用途插头和插座的IEC系统. 第2部分. 15 A 125伏交流电和20 A 125伏交流电插头和插座

IEC system of plugs and socket-outlets for household and similar purposes. Part 2. Plugs and socket-outlets 15 A 125 V a.c. and 20 A 125 V a.c.

SNI IEC 60633:2015 高压直流（HVDC）输电术语

TERMINOLOGY FOR HIGH-VOLTAGE DIRECT CURRENT (HVDC) TRANSMISSION

GSO IEC 62196-2:2014 插头、插座、车辆连接器和车辆入口 电动汽车传导充电 第2部分：交流插针和接触管配件的尺寸兼容性和互换性要求

This standard applies to plugs, socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. They have a nominal rated operating voltage not exceeding 500 V a.c., 50 to 60 Hz, and a rated current not exceeding 63 A three-phase or 70 A single phase, for use in conductive charging of electric vehicles. This standard covers the basic interface accessories for vehicle supply as specified in IEC 62196-1, and intended for use in conductive charging systems for circuits specified in IEC 61851-1:2010. Electric vehicles covers all road vehicles, including plug-in hybrid road vehicles (PHEV), that derive all or part of their energy from on-board batteries. NOTE 1 These accessories may provide a contact that can be used for the proximity contact function. These accessories are intended to be used for circuits specified in IEC 61851-1:2010 which operate at different voltages and frequencies and which may include ELV and communication signals. These accessories may be used for bidirectional energy transmission (under consideration). This standard applies to the accessories to be used in an ambient temperature of between – 30 °C and + 50 °C. NOTE 2 In the following country, other requirements may apply: FI. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. Vehicle inlet and vehicle connector to this standard are intended to be used for charging in modes 1, 2 and 3, cases B and C. The socket-outlets and plugs covered by this standard are intended to be used for charging mode 3 only, case A and B. The modes and permissible connections are specified in Part 1.

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories

GSO IEC TR 60083:2014 国际电工委员会 (IEC) 成员国标准化的家用和类似公共用途插头和插座

The object of this technical report is to give general information about the systems of plugs and socket-outlets for household and similar purposes which are used in the IEC countries. The report only contains National Systems which are commonly used in homes and offices. It is therefore limited to systems for a.c. with a rated voltage above 50 V but not exceeding 440 V, intended for household and similar purposes, either indoors or outdoors. The report only contains systems for which standard sheets have been published in a National Standard, which may be a National Standard of the country itself or any other IEC member country.

Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC

GSO IEC 60320-2-2:2014 家用和类似通用用途的器具耦合器 第2-2部分：家用和类似设备的互连耦合器

This clause of IEC 60320-1 is replaced as follows: This standard is applicable to two-pole interconnection couplers for a.c. only, with and without earthing contact, with a rated voltage not exceeding 250 V and a rated current not exceeding 16 A, for household and similar appliances and equipment and intended for the interconnection of the electrical supply to electrical appliances or equipment for 50 Hz or 60 Hz supply. Appliance outlets integrated in or incorporated in appliances or other equipment are within the scope of this standard. The dimensional and general requirements of this standard apply to such outlets, but certain tests may not be relevant. The requirements for plug connectors are based on the assumption that the temperature of the socket contacts of the corresponding appliance outlets does not exceed 65 °C (cold conditions). Interconnection couplers complying with this standard are suitable for use at ambient temperatures not normally exceeding 25 °C, but occasionally reaching 35 °C. Interconnection couplers complying with the standard sheets in this standard are intended for the interconnection of appliances or equipment having no special protection against moisture; for the interconnection of other appliances or equipment and of an appliance or equipment which is subject to spillage of liquid in normal use, additional requirements are necessary. Special constructions may be required – in locations where special conditions prevail as, for example, in ships, vehicles and the like; – in hazardous locations, for example, where explosions are liable to occur.

Appliance couplers for household and similar general purposes - Part 2-2: Interconnection couplers for household and similar equipment

GSO IEC 60320-2-3:2014 家用和类似通用用途的器具耦合器 第2-3部分：防护等级高于IPX0的器具耦合器

This clause of IEC 60320-1 applies amended as follows: This standard applies to two-pole non-reversible appliance couplers for cold conditions for a.c. only, with a degree of protection against ingress of water higher than IPX0, with a rated voltage not exceeding 250 V and a rated current not exceeding 10 A for a 50 Hz or 60 Hz supply. They are intended for the connection of the circular supply cord to electrical appliances of class II for household, commercial and light industrial use. NOTE 1 This note of IEC 60320-1 applies. NOTE 2 This note of IEC 60320-1 applies. NOTE 3 This note of IEC 60320-1 applies. NOTE 4 This note of IEC 60320-1 does not apply. NOTE 5 This note of IEC 60320-1 applies. Additional notes: NOTE 6 IEC 60529 specifies the degree of protection against the ingress of water (IP code). NOTE 7 IEC 60536 specifies the class of equipment.

Appliance couplers for household and similar general purposes - Part 2-3: Appliance couplers with a degree of protection higher than IPX0

DIN EN 60309-1 Berichtigung 1:2014 工业用插头, 插座和耦合器. 第1部分: 通用要求 (IEC 60309-1-1999 + A1-2005, 修订版 + A2-2012); 德文版本EN 60309-1-1999 + A1-2007 + A2-2012, DIN EN 60309-1 (VDE 0623-1)-2013-02的勘误表; (IEC-IEC 60309-1-1999/A1-2005的勘误表-2014)

Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements (IEC 60309-1:1999 + A1:2005, modified + A2:2012); German version EN 60309-1:1999 + A1:2007 + A2:2012, Corrigendum to DIN EN 60309-1 (VDE 0623-1):2013-02; (IEC-Cor.:2

KS C IEC 60309-4-2014(2019) 插头 插座和耦合器用于工业目的 - 第4部分:开关插座和连接器或不带互锁

Plugs, socket-outlets and couplers for industrial purposes — Part 4: Switched socket-outlets and connectors with or without interlock

KS C IEC 60309-4:2014 工业用插头、插座和连接器.第4部分:有或没有互锁的开关插座和连接器

Plugs, socket-outlets and couplers for industrial purposes — Part 4: Switched socket-outlets and connectors with or without interlock

KS C IEC 60320-2-2-2014(2019) 家用和类似用途电器耦合器通用第2-2部分:家用和类似设备用互连耦合器

Appliance couplers for household and similiar general purpose — Part 2-2: Interconnection couplers for household and similar equipment

KS C IEC 60320-2-2:2014 家用和类似一般用途电器连接器.第2-2部分:家用和类似设备用互联耦合器

제1부의 이 항을 다음으로 대체한다.이 표준은 가정용 및 유사설비의 250 V 이하의 정격전압과 16 A 이하의 정격전류를 갖는 50 Hz 또는 60 Hz 전기기기 또는 설비의 전원공급기에 연결되는 접지극 유무에 무관한 교류 2극 연결 커플러에 대해 적용한다.기기 또는 장비에 통합적이거나 일체적인 기기용 콘센트는 이 표준에 따르며 이 표준에서 중요하고 일반적인 요구사항은 그러한 기기에 적용된다. 그러나 어떤 시험은 연관 없을 수도 있다.플러그 연결기에 대한 요구사항은 대응하는 기기용 콘센트의 소켓접촉의 온도가 65 ℃를 초과하지 않는다는(저온조건) 가정에 기초한다.이 표준에 따르는 연결 커플러는 정상적으로 25 ℃를 넘지 않으나 때로 35 ℃까지 도달하는 주위온도에서 사용하는 것이 적절하다.이 표준에서의 표준시트를 따르는 연결 커플러는 습기에 대한 특별한 방어책을 가지지 않는 기기나 장비의 연결을 지향한다. 또 다른 기기나 장비 그리고 보통의 사용상에서 액체에 노출될만한 기기나 장비에 대해서 부가적인 요구사항이 필요하다.다음에서 특수한 구조가 필요할 수 있다.― 예를 들면 배에서처럼 운송수단과 그와 같은 것들에 노출되어 있는 특수한 조건의 장소에서― 예를 들면 폭발이

Appliance couplers for household and similiar general purpose — Part 2-2: Interconnection couplers for household and similar equipment

IEC 60320-3:2014 家用和类似用途的器具耦合器. 第3部分: 标准板和仪表

This part of the lEC 60320 sets the dimensions for appliance couplers for two poles and two poles with earth contact ?C for the connection of electrical devices for household and similar onto the mains supply and ?C for the interconnection of the electrical supply to appliance or equipment ?C and dimensions for gauges.

Appliance couplers for household and similar general purposes - Part 3: Standard sheets and gauges

KS C IEC 60906-3-A-2014(2019) 第3部分IEC标准插头 家用和类似用途的插座:SELV插头和插座

IEC System of plugs and socket-outlets for household and similar purposes — Part 3: SELV plugs and socket-outlets, 16 A 6V, 12 V, 24 V, 48 V, a.c. and d.c.