29.120.40 开关 标准查询与下载

JB/T 13991-2020 无刷电动工具用开关

Brushless power tool switches

EN IEC 63180:2020 检测器检测范围的测量方法和声明 用于主要和次要运动检测的被动红外检测器

IEC 63180:2020 provides a methodology and test procedures to be able to declare and verify the detection area for motion detectors using passive infrared technology in electronic control devices and appliance switches, whether stand-alone (direct control of one or more applications) or as part of home and building electronic systems or building automation control systems (HBES/BACS) or similar.

Methods of measurement and declaration of the detection range of detectors - Passive infrared detectors for major and minor motion detection

T/CEC 350-2020 10kV带电作业用消弧开关技术条件

本标准规范了10kV带电作业用消弧开关的技术要求、试验方法、使用注意事项、检验规则以及标志、包装、运输和贮存等。 本标准适用于10kV带电作业中使用的消弧开关。

Technical conditions of arc suppression switch for 10kV live working

IEC 63180:2020 探测器探测范围的测量和声明方法.主要和次要运动探测用被动红外探测器

Methods of measurement and declaration of the detection range of detectors - Passive infrared detectors for major and minor motion detection

CSA C22.2 No.61058-2-6-2020 器具开关 第2-6部分：电动手持工具、移动工具以及草坪和园林机械中使用的开关的特殊要求

1 Scope Clause 1 of IEC 61058-1:2016 is applicable except as follows. Addition: This part of IEC 61058 is a subset based on IEC 61058-1. The clauses outlined below are intended to address the specific requirements for switches incorporated into or integrated with electric motor-operated hand-held tools, transportable tools and lawn and garden machinery. This document is intended for switches with an ambient temperature up to and including 55 °C. Switches tested according to IEC 61058-1 are considered to comply with this document and additional testing is not required provided ratings, loads, and endurance are correct. NOTE This document takes into account the fact that tests are conducted as part of the end-product evaluation (e.g. products tested according to the IEC 60745 and IEC 62841 series, and lawn and gardening equipment tested according to the IEC 60335 series), and that tests are not conducted on the component switch.

Switches for appliances — Part 2-6: Particular requirements for switches used in electric motor-operated hand-held tools, transportable tools and lawn and garden machinery

CSA C22.2 No.61058-2-5-2020 器具开关 第2-5部分：转换选择器的特殊要求

1 Scope Replacement: This Part of IEC 61058 applies to change-over selectors (mechanical or electronic) for appliances actuated by hand, by foot or by other human activity, to operate or control electrical appliances and other equipment for household or similar purposes with a rated voltage not exceeding 480 V and a rated current not exceeding 63 A. These change-over selectors are intended to be operated by a person, via an actuating member or by actuating a sensing unit. The actuating member or sensing unit can be integral with or arranged separately, either physically or electrically, from the switch, and can involve transmission of a signal, for example electrical, optical, acoustic or thermal, between the actuating member or sensing unit and the switch. Change-over selectors which incorporate additional control functions governed by the switch function are within the scope of this document. This document also covers the indirect actuation of the switch when the operation of the actuating member or sensing unit is provided by a remote control or a part of an appliance or equipment such as a door. NOTE 1 Electronic change-over selectors can be combined with mechanical change-over selectors giving full disconnection or micro-disconnection. NOTE 2 Electronic change-over selectors without a mechanical switch in the supply circuit provide only electronic disconnection. Therefore, the circuit on the load side is always considered to be live. NOTE 3 For change-over selectors used in tropical climates, additional requirements can apply. NOTE 4 Attention is drawn to the fact that the standards for appliances can contain additional or alternative requirements for changeover selectors. NOTE 5 Throughout this document, the word "appliance" means "appliance or equipment". This document applies to change-over selectors intended to be incorporated in, on, or with an appliance. This document also applies to change-over selectors incorporating electronic devices.

Switches for appliances — Part 2-5: Particular requirements for change-over selectors

EN IEC 60947-5-2:2020 低压开关设备和控制设备 第 5-2 部分：控制电路设备和开关元件 接近开关

IEC 60947-5-2:2019 applies to inductive and capacitive proximity switches that sense the presence of metallic and/or non-metallic objects, ultrasonic proximity switches that sense the presence of sound reflecting objects, photoelectric proximity switches that sense the presence of objects and non-mechanical magnetic proximity switches that sense the presence of objects with a magnetic field. This fourth edition cancels and replaces the third edition published in 2007 and Amendment 1:2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: update of the scope; adaptation and update of the construction requirements according to IEC Guide 116 (e.g. material requirements, artificial optical radiation, instruction requirements, hot surface, unattended operation, foreseeable misuse…); modification of the specifications concerning the sensing range and operating distance; new definitions for photoelectric proximity switch type D with background suppression; integration of the requirements and test procedures of photoelectric proximity switch type D with background suppression; update of EMC requirements in Table 9 and Table 10; integration of environmental information requirements and environmental condition by referencing Annexes O, W and Q of IEC 60947-1:2007, IEC 60947-1:2007/AMD1:2010 and IEC 60947-1:2007/AMD2:2014; modification of impulse withstand voltage test (5.3.1.3, 9.3.3.4.5); modification of the references in the (normative) standard body to the (informative) Annex A; major update of Annex A (definitions update, new dimensions and shapes); update of C.9.1.1; update of Annex D in order to consider new connector types and normative references; update of Annex F (additional symbols for photoelectric proximity switches).

Low-voltage switchgear and controlgear - Part 5-2: Control circuit devices and switching elements - Proximity switches

BS EN 60669-1:2018 家用和类似固定电气装置的开关 一般要求

1   Scope This part of IEC 60669 applies to manually operated general purpose functional switches, for alternating current (AC) only with a rated voltage not exceeding 440 V with a rated current not exceeding 63 A, intended for household and similar fixed electrical installations, either indoors or outdoors. For switches provided with screwless terminals , the rated current is limited to 16 A. NOTE 1 The rated current is limited to 16 A for switches provided with insulation piercing terminals ( IPT ’s) according to Annex D. Switches covered by this document are, where applicable, intended for the control in normal use of all of the following loads: — a circuit for a tungsten filament lamp load; — a circuit for an externally ballasted lamp load (for example LED, CFL, fluorescent lamp load); — a circuit for a self ballasted lamp load (for example LEDi or CFLi); — a circuit for a substantially resistive load with a power factor not less than 0,95;

Switches for household and similar fixed-electrical installations - General requirements

T/CSEE 0155-2020 智能隔离断路器检修决策导则

本标准规定了智能隔离断路器的检修决策基本原则、检修分类和检修决策等。 本标准适用于交流额定电压72.5kV~330kV的智能隔离断路器。

Decision-making guidelines for maintenance of intelligent isolating circuit breakers

T/CAS 385-2019 智能开关及类似功能产品智能水平评价技术规范

本标准规定了智能开关及类似功能产品智能功能的评价指标体系及智能水平等级、评价指标和测评方法。

Technical specification for evaluation of intelligent level of smart switches and products with similar functions

KS C 6038-2019 电子设备用拨动开关

Toggle switches for use in electronic equipment

KS C 8309-2019 室内使用的小型开关

Small switches for indoor use

KS C IEC 60265-1-2019 高压开关 第1部分：额定电压1kV以上52kV以下开关

High-voltage switches－Part 1：Switches for rated voltages above 1kV and less than 52kV

ASTM F2188-02(2019) 测定薄膜开关或薄膜开关组件上变频振动影响的标准试验方法

1.1 This test method establishes procedures for determining the effect of sinusoidal vibration, within the specified frequency range, on switch contacts, mounting hardware, adhered component parts, solder or heat stakes, tactile devices, and cable or ribbon interconnects associated with a membrane switch or membrane switch assembly. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Effect of Variable Frequency Vibration on a Membrane Switch or Membrane Switch Assembly

ASTM F2187-02(2019) 确定随机频率振动对膜开关或膜开关组件的影响的标准测试方法

1.1 This test method establishes procedures for determining the effect of random vibration, within the specified frequency range, on switch contacts, mounting hardware, adhered component parts, solder or heat stakes, tactile devices, and cable or ribbon interconnects associated with a membrane switch or membrane switch assembly. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Effect of Random Frequency Vibration on a Membrane Switch or Membrane Switch Assembly

T/ZZB 1204-2019 软起动器

本标准规定了软起动器的术语和定义、符号、代号、基本要求、基本参数、正常工作条件和安装条件、技术要求、试验方法、检验规则、标志、包装、运输和储存、质量承诺。 本标准适用于预期与额定电压不超过交流1 000 V的电路相连的交流电动机用软起动器。 注： 1 140 V电压等级的软起动器可参照本部分执行。

Soft starter

EN IEC 60934:2019 设备用断路器（CBE）

IEC 60934:2019 is available as IEC 60934:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60934:2019 is applicable to mechanical switching devices designed as "circuit‑breakers for equipment" (CBE) for household and similar applications. CBEs according to this document are intended to provide protection to circuits within electrical equipment including its components (e.g. motors, transformers, internal wiring). This document covers also CBEs applicable for protection of electrical equipment in case of undervoltage and/or overvoltage. This document also covers CBEs which are suitable for isolation. This fourth edition cancels and replaces the third edition published in 2000, Amendment 1:2007 and Amendment 2:2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) clarifications for type testing purposes.

Circuit breakers for equipment (CBE)

JB/T 6475-2019 光电开关

Photoelectric switch

JBT6475-2019 光电开关

Photoelectric switch

T/ZZB 1116-2019 交流电动工具用电子模块

本标准主要规定了交流电动工具用电子模块（以下简称电子模块）的术语和定义、额定值、分类、型号与标志、基本要求、技术要求与试验方法、检验规则、包装、运输和贮存及质量承诺。 本标准适用于电压不超过AC250 V、电流不大于30 A的交流电动工具或类似用途器具中进行调速、限速、软起动、恒功率、恒速等控制的电子模块；以及由人通过操动件操作电动工具开关时才能起到控制作用的与开关结合为一个整体或单独制成附件的电子模块。 注1：与提供完全断开或微断开的机械开关组合在一起的电子模块适用于本标准。 注2：仅提供电子断开的电子模块适用于本标准。 在特殊环境下使用的电子模块或特殊用途的电子模块也可参照本标准。

Electronic block for alternating electric tools