29.120.40 开关 标准查询与下载

DIN 43633-1:2011 旋转隔离开关.第1部分:额定电压123 kV.端子和安装尺寸,布置图

Centre break disconnector - Part 1: Rated voltage 123 kV - Terminal and mounting dimensions, layout

IEEE Std C37.10-2011 电力断路器故障的调查研究,分析和报告指南

Guide for Investigation, Analysis, and Reporting of Power Circuit Breaker Failures

ANSI/UL 363-2011 闸刀开关安全标准

This proposed Eleventh Edition of the Standard for Knife Switches is being issued to obtain ANSI approval. No technical changes have been made to this standard.

Standard for Safety for Knife Switches

ANSI/IEEE C37.10:2011 电力断路器故障调查研究,分析和报告指南

Guide for Investigation, Analysis and Reporting of Power Circuit Breaker Failures

ANSI/IEEE C37.011:2011 交流高压断路器瞬时恢复电压的应用指南

Guide for the Application of Transient Recovery Voltage for AC High-Voltage Circuit Breakers

LST EN 60669-2-1-2004/A12-2010 家用和类似用途固定电气装置的开关 第 2-1 部分：特殊要求 电子开关

Switches for household and similar fixed electrical installations -- Part 2-1: Particular requirements - Electronic switches

IEC 61058-2-1:2010 开关器具.第2-1部分:拉线开关的详细要求

This clause of Part 1 is applicable except as follows: 1.1 Replacement: 1.1 This International Standard applies to cord switches (mechanical or electronic) for appliances actuated by hand, by foot or by other human activity, to operate or control electrical appliances and other equipment for household or similar purposes with a rated voltage not exceeding 250 V and a rated current not exceeding 16 A. These switches are intended to be operated by a person, via an actuating member or by actuating a sensing unit. The actuating member or sensing unit can be integral or arranged separately from the switch. The transmission of a signal between the actuating member or sensing unit and the switch may be made either physically or electrically (for example electrical, optical, acoustic or thermal). Switches which incorporate additional control functions governed by the switch function are within the scope of this standard. This standard also covers the indirect actuation of the switch when the operation of the actuating member or sensing unit is provided by a remote control or a part of an appliance or equipment such as a door. NOTE 1 Electronic switches may be combined with mechanical switches giving full disconnection or microdisconnection. NOTE 2 Electronic switches without a mechanical switch in the supply circuit provide only electronic disconnection. Therefore, the circuit on the load side is always considered to be live. NOTE 3 For switches used in tropical climates, additional requirements may be necessary. NOTE 4 Attention is drawn to the fact that the standards for appliances may contain additional or alternative requirements for switches. NOTE 5 Throughout this standard, the word “appliance” means “appliance or equipment”. 1.2 Replacement: 1.2 This standard applies to switches intended to be connected to a flexible cable." NOTE In this document, the word “cable” means “cable or cord”. 1.3 This subclause applies. 1.4 This subclause does not apply.

Switches for appliances - Part 2-1: Particular requirements for cord switches

IEC 61058-2-5:2010 电器开关.第2-5部分:转换选择器的详细要求

1.1 This International Standard applies to change-over selectors (mechanical or electronic) for appliances actuated by hand, by foot or by other human activity, to operate or control electrical appliances and other equipment for household or similar purposes with a rated voltage not exceeding 480 V and a rated current not exceeding 63 A. These change-over selectors are intended to be operated by a person, via an actuating member or by actuating a sensing unit. The actuating member or sensing unit can be integral with or arranged separately, either physically or electrically, from the switch and may involve transmission of a signal, for example electrical, optical, acoustic or thermal, between the actuating member or sensing unit and the switch. Change-over selectors which incorporate additional control functions governed by the switch function are within the scope of this standard. This standard also covers the indirect actuation of the switch when the operation of the actuating member or sensing unit is provided by a remote control or a part of an appliance or equipment such as a door. NOTE 1 Electronic change-over selectors may be combined with mechanical change-over selectors giving full disconnection or micro-disconnection. NOTE 2 Electronic change-over selectors without a mechanical switch in the supply circuit provide only electronic disconnection. Therefore, the circuit on the load side is always considered to be live. NOTE 3 For change-over selectors used in tropical climates, additional requirements may be necessary. NOTE 4 Attention is drawn to the fact that the standards for appliances may contain additional or alternative requirements for change-over selectors. NOTE 5 Throughout this standard, the word "appliance" means "appliance or equipment". 1.2 This standard applies to change-over selectors intended to be incorporated in, on or with an appliance. 1.3 This standard also applies to change-over selectors incorporating electronic devices.

Switches for appliances - Part 2-5: Particular requirements for change-over selectors

DS/EN 60669-2-1/A12:2010 家用和类似用途固定电气装置的开关 第 2-1 部分：特殊要求 电子开关

Applies to electronic switches and to associated electronic extension units for household and similar fixed electrical installations either indoors or outdoors.

Switches for household and similar fixed electrical installations - Part 2-1: Particular requirements - Electronic switches

DS/HD 639 S1/A2:2010 电气附件 家用和类似用途的不带整体过电流保护的便携式剩余电流装置（PRCD）

Applies to portable devices consisting of a plug, a residual current device (RCD) and one or more socket-outlets or a provision for connection. They do not incorporate overcurrent protection. They are intended for single-phase circuits for rated currents not exceeding 16 A for rated voltages not exceeding 250 V a.c., or for rated current not exceeding 32 A for rated voltages not exceeding 130 V a.c. to earth.

Electrical accessories - Portable residual current devices without integral overcurrent protection for household and similar use (PRCDs)

IEEE Std C37.13.1a-2010 附金属壳的低压电力断路器开关装置用专用开关装置.修改件1:对短路等级评定和测试要求的修订

IEEE Standard for Definite-Purpose Switching Devices for Use in Metal- Enclosed Low-Voltage Power Circuit Breaker Switchgear; Amendment 1: Revise Short-Circuit Rating and Test Requirement

Definite-purpose switching devices for use in metal-enclosed low-voltage power circuit breaker switchgear; Amendment 1: Revise short-circuit rating and test requirement

DIN EN 60669-2-1/A12:2010 家用和类似用途固定电气设施用开关.第2-1部分:详细要求.电子开关.德文版本EN 60669-2-1-2004/A12-2010

Switches for household and similar fixed electrical installations - Part 2-1: Particular requirements - Electronic switches; German version EN 60669-2-1:2004/A12:2010

UL 20-2010 通用拨动开关

UL Standard for Safety General-Use Snap Switches (Thirteenth Edition; Reprint with Revisions Through and Including February 17, 2012)

ASTM F1662-10 检验薄膜开关的规定介电耐受电压和确定介电击穿电压的标准试验方法

Dielectric withstand voltage testing is useful for design verification, quality control of materials, and workmanship. This test method is used to verify that the membrane switch can operate safely at its rated voltage, and withstand momentary overpotentials due to switching, surges and other similar electrical phenomena. Specific areas of testing are, but not limited to: Conductor/dielectric/conductor crossing point, Close proximity of conductors, and Any other conductive surface such as shielding or metal backing panel. Dielectric withstand voltage testing may be destructive and units that have been tested should be considered unreliable for future use. Testing using ac voltage may be useful for switches intended for control circuits powered by ac voltages.1.1 This test method covers the verification of a specified dielectric withstand voltage or dielectric breakdown voltage of a membrane switch.

Standard Test Method for Verifying the Specified Dielectric Withstand Voltage and Determining the Dielectric Breakdown Voltage of a Membrane Switch

DIN EN 60669-2-1:2010 家用和类似用途的固定电气设施用开关.第2-1部分:特殊要求.电子开关

This standard also applies to automatc electronic switches where the operation and/or control is initiateed by physical means, for example light, temperature, humidity, time, wind velocity, presence of persons, etc.

Switches for household and similar fixed electrical installations - Part 2-1: Particular requirements - Electronic switches (IEC 60669-2-1:2002, modified + A1:2008, modified); German version EN 60669-2-1:2004 + A1:2009

JB/T 9614-2010 LW95系列船用万能转换开关

本标准规定了LW95系列船用万能转换开关(以下简称转换开关)的定义、分类、特性、结构要求和试验等。 本标准适用于LW95系列转换开关的设计、制造和检验。该转换开关安装在船舶上，主要用于交流电压至500 V(50 Hz或60 Hz)及直流电压至440 V的电路中转换电气控制线路(例如电磁线圈、电气测量仪表和伺服电动机等)，也可用于交流380 V、5.5 kW及以下三相鼠笼型异步电动机的直接控制(起动、可逆转换和多速电机变速等)。

LW95 series change-over switch in ships

DIN EN 60669-1 Berichtigung 1:2010 家用及类似电气安装用开关.第1部分:通用要求(IEC 60669-1-1998+A1-1999+A2-2006).德文版本EN 60669-1-1999 + A1-2002 +勘误表2007+ A2-2008,DIN EN 60669-1 (VDE 0632-1)-2009-10的勘误表

Corrigendum to DIN EN 60669-1 (VDE 0632-1):2009-10.

Switches for household and similar fixed-electrical installations - Part 1: General requirements (IEC 60669-1:1998, modified + A1:1999, modified + A2:2006, modified); German version EN 60669-1:1999 + A1:2002 + Corrigendum:2007 + A2:2008, Corrigendum to DI

IEEE Std C37.09b-2010 额定电流基准交流高压电路断路器用测试规程.修改件2:与IEC 62771-100标准协调一致的瞬变恢复电压描述的改变

Test procedure for AC high-voltage circuit breakers rated on a symmetrical current basis - Amendment 2: To change the description of transient recovery voltage for harmonization with IEC 62271-100

ANSI/IEEE C37.13.1a:2010 附金属壳的低压电力断路器开关设备用专用开关装置的标准.修改件:修订短路等级和试验设备

This amendment to the standard revises the short-circuit rating and test requirements for definite purpose switching devices for use in metal-enclosed low-voltage power circuit breaker switchgear

Standard for Definite-Purpose Switching Devices for Use in Metal-Enclosed Low-Voltage Power Circuit Breaker Switchgear - Amendment: Revise Short-Circuit Rating and Test Requirement

ANSI/IEEE C37.09b:2010 额定电流基准交流高压电路断路器用标准试验规程.修改件2:与IEC 62771-100标准协调一致的瞬变恢复电压描述的改变

This test procedure summarizes the various tests that are made on ac high-voltage indoor and outdoor circuit breakers, except for generator circuit breakers, which are covered in IEEE Std C37.013-1997. It describes accepted methods used in making the tests and specifies the tests that will verify assigned ratings under ANSI/IEEE standards. This procedure does not preclude the use of other equivalent or more effective methods of demonstrating ratings.

Standard Test Procedure for AC High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis -Amendment 2: To Change the Description of Transient Recovery Voltage for Harmonization with IEC 62271-100