29.120.99 其他电工器件 标准查询与下载

NF C63-316*NF EN 61316:2000 工业用电缆卷筒

Industrial cable reels.

ASTM E1934-99a 用红外热成像法检查电气和机械设备的标准指南

Standard Guide for Examining Electrical and Mechanical Equipment with Infrared Thermography

IEC 61316:1999 工业电缆卷筒

This International Standard applies to cable reels provided with a non-detachable flexible cable with a rated operating voltage not exceeding 690 V a.c./d.c. and 500 Hz with a rated current not exceeding 63 A, primarily intended for industrial use, either indoors or outdoors, for use with accessories complying with IEC 60309-1 or IEC 60309-2. This standard applies to: - portable cable reels equipped with one plug or appliance-inlet and at least one socket-outlet, each complying with IEC 60309-1 or IEC 60309-2; - fixed cable reels equipped with at least one socket-outlet complying with IEC 60309-1 or IEC 60309-2; - cable reels suitable for use at ambient temperature normally within the range of -25 ℃ to +40 ℃. The use of this equipment on construction sites and for agricultural, commercial and domestic appliances are not precluded. This standard also applies to cable reels intended to be used in extra-low voltage installations. In locations where special conditions prevail, for example, on board ships, vehicles and the like, or where explosions are liable to occur, additional requirements may be necessary. NOTE - Additional requirements for cable reels for currents higher than 63 A are under consideration.

Industrial cable reels

DS/EN 60110-1:1999 感应加热装置用电力电容器 第1部分：总则

This part of IEC 60110 is applicable both to indoor capacitor units and indoor capacitor banks intended to be used, particularly, for power factor correction in induction heating, melting, stirring or casting installations, and similar applications with controlled or adjustable a.c. voltage systems in a frequency range up to 50 kHz, and with a rated voltage not exceeding 3,6 kV.

Power capacitors for induction heating installations - Part 1: General

NF C61-910F1:1999 关于1984年4月NF C 61-910标准的第99-101号解读手册.

Interpretation Manual No. 99-101 on the April 1984 NF C 61-910 standard.

ASTM E1934-99a(2010) 用红外线温度记录法检查电气及机械设备的标准指南

This guide can be used by an end user to specify infrared examinations of electrical and mechanical equipment and an infrared thermographer to perform them. This guide lists the joint responsibilities of the end user and the infrared thermographer when using infrared thermography. The purpose of an infrared examination is to identify and document exceptions in the end user''s electrical or mechanical systems, or both. In electrical equipment, warm exceptions are usually created by an increase in resistance caused by loose or deteriorated connections, short circuits, overloads, load imbalances or faulty, mismatched or improperly installed components. Cool exceptions are usually caused by failed components. In mechanical equipment, warm exceptions are usually created by friction caused by improper lubrication, misalignment, worn components or mechanical loading anomalies. Cool exceptions are usually caused by failed components. Exceptions in insulation systems are usually caused by missing or deteriorated materials, improper installation or insufficient amounts of material. Providing opinions about the causes of exceptions, the integrity of the equipment or recommendations for corrective actions require knowledge and skills beyond those of infrared thermography. Infrared examinations provide data about equipment at the time of examination only. Infrared examinations are not remedial. An infrared examination of electrical and mechanical equipment does not assure its proper operation. Other tests and proper maintenance are necessary to ensure their reliable performance.1.1 This guide lists the responsibilities of the end user and the infrared thermographer when examining electrical and mechanical systems. 1.2 This guide outlines the specific content required to document qualitative and quantitative infrared examinations of electrical and mechanical equipment. 1.3 This guide may involve use of equipment and materials in the presence of heated, moving or all of these or electrically energized equipment. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Examining Electrical and Mechanical Equipment with Infrared Thermography

GOST R 51539-1999 家用与类似用途的电缆盘.一般要求及测试方法

Настоящий стандарт распространяется на удлинители на кабельных катушках переменного тока с несъемным гибким кабелем, предназначенные дл

Cable reels for household and similar purposes. General requirements and test methods

DS/EN 61242:1998 电气附件 家用和类似用途的电缆卷筒

This International Standard applies to cable reels for a.c. only, provided with a non-detachable flexible cable with a rated voltage above 50 V and not exeeding 250 V for single-phase cable reels and above 50 V and not exceeding 440 V for all other cable reels, and a rated current not exceeding 16 A.

Electrical accessories - Cable reels for household and similar purposes

BS EN 61242:1998 电气附件.家用和类似用途电缆卷轴

This International Standard applies to cable reels for a.c. only, provided with a non-detachable flexible cable with a rated voltage above 50 V and not exceeding 250 V for single-phase cable reels and above 50 V and not exceeding 440 V for all other cable reels, and a rated current not exceeding 16 A. They are intended for household, commercial and light industrial and similar purposes, either indoors or outdoors, with particular reference to safety in normal use. This standard does not apply to: —cable reels with a detachable cable; —cable reeling devices incorporated in appliances. NOTE Requirements for cable reeling devices incorporated in appliances are specified in EN 60335-1 and EN 60335-2-2. Cable reels complying with this standard are suitable for use at ambient temperatures not normally exceeding 25 ℃, but occasionally reaching 35 ℃. In locations where special conditions prevail, special construction may be required.

Electrical accessories - Cable reels for household and similar purposes

BS EN 61242:1997+A1:2008 电气原件.家用和类似用途的电缆卷轴

This International Standard applies to cable reels for a.c. only, with a rated voltage above 50 V and not exceeding 250 V for single-phase cable reels and above 50 V and not exceeding 440 V for all other cable reels, and a rated current not exceeding 16 A. They are intended for household, commercial and light industrial and similar purposes, either indoors or outdoors, with particular reference to safety in normal use. This standard does not apply to: — cable reeling devices incorporated in appliances or luminaires; — cable reeling devices associated with appliances or luminaires. This standard may be used as a guide for cable reeling devices incorporated or associated in appliances or luminaires as far as it is applicable. Cable reels complying with this standard are suitable for use at ambient temperatures not normally exceeding 25 °C, but occasionally reaching 35 °C. In locations where special conditions prevail, special construction may be required.

Electrical accessories. Cable reels for household and similar purposes

BS EN 61242+A1:1998 电气附件 家用和类似用途电缆卷轴

Electrical accessories. Cable reels for household and similar purposes

CNS 13811-1997 发光二极管数字型反射套板

本标准适用于发光二极管数字型反射套板，本标准规格要项及检验之项目。

Numerical-Type Reflectors for Light Emitting Diodes

TIS 1389-1996 滚筒式干衣机.安全要求

Tumbler dryers: safety requirements

IEC 61242:1995 电气附件 家用和类似用途卷线盘

This International Standard applies to cable reels for a.c. only, provided with a non-detachable flexible cable with a rated voltage above 50 V and not exceeding 250 V for single-phase cable reels and above 50 V and not exceeding 440 V for all other cable reels, and a rated current not exceeding 16 A. They are intended for household, commercial and light industrial and similar purposes, either indoors or outdoors, with particular reference to safety in normal use. Cable reeling devices incorporated in appliances are under consideration. Cable reels complying with this standard are suitable for use at ambient temperatures not normally exceeding 25 ℃, but occasionally reaching 35 ℃. In locations where special conditions prevail, special construction may be required. NOTE - This standard does not apply to cable reels with a detachable flexible cable.

Electrical accessories - Cable reels for household and similar purposes

GSO 157:1993 家用电器中使用的压力式恒温器

لا يوجـد

Pressure type thermostats for use in household electrical appliances.

IEC 61035-2-2:1993 电气装置用导管配件规范 第2部分:特殊要求 第2节:绝缘材料导管配件

Is to be used in conjunction with IEC 1035-1: Specification for conduit fittings for electrical installations, Part 1: General requirements. The clauses of part 1 apply except of the replacements, deletions, additions and amendments given. Includes stand

Specification for conduit fittings for electrical installations; part 2: particular specifications; section 2: conduit fittings of insulating material

IEC 60684-3-201:1991 绝缘软套管规范.第3部分:各种型号套管的规范要求.第201活页:交联聚氯乙烯、收缩率为2:1可收缩通用软套管

Specification for flexible insulating sleeving; part 3: specification requirements for individual types of sleeving; sheet 201: heat shrinkable sleeving, general purpose, flexible, cross-linked PVC, shrink ratio 2:1

CNS 11901-1987 一般电子设备用机架及单体机座之尺度

本标准规定一般电子装备用机架及单体机座之主要尺度。

Dimensions of Racks and Unit Chassis of Electronic Equipment for General Use

CSA C22.2 No.39-M1987-1987(R2013) 保险丝座组件

1. Scope 1.1 This Standard applies to fuseholder assemblies, rejectors for Type C fuses, adapters for Type S fuses, and the current-carrying parts pertaining thereto and mounted on bases of suitable insulating material, designed to be employed in accordance with the Canadian Electrical Code, Part I. 1.2 Fuseholder assemblies covered by this Standard are intended to accept only the following fuses: (a) plug fuses, including Type S fuses, not exceeding 30 A and 125 V and conforming to CSA Standard C22.2 No.59, Fuses (Both Plug and Cartridge-Enclosed Types); (b) cartridge fuses not exceeding 600 A and 600 V and conforming to CSa Standard C22.2 No.59, Fuses (Both Plug and Cartridge-Enclosed Types); and (c) HRC fuses not exceeding 6000 A and 600 V and conforming to CSA Standard C22.2 No.106, HRC Fuses (Low-Voltage Power Fuses). 1.3 This Standard also applies to the construction of contact members which are used as integral parts of fusible devices or equipment covered by other Part II Standards (see Clause 3.3).

Fuseholder Assemblies

CNS 5022-1984 电焊机用闸流调节器

本标准适用于标称电压 220V 或 440V 50 Hz 或 60 Hz 单相交流线路，使用 2 个闸流调节器（以下简称闸流器）以顺逆向并联连接使用之电焊机用闸流调节器（以下简称闸流器组）。

Thyristorstack for Welding Machine