29.130.01 开关装置和控制器综合 标准查询与下载

ANSI/IEEE C37.81:1989 1E类金属壳电源开关装置组件的抗震合格鉴定

Provides requirements and guidance for the seismic qualification of metal-enclosed power switchgear assemblies including switching, interrupting, control, instrumentation, metering, and protective and regulating devices mounted therein.

Guide for Seismic Qualification of Class 1E Metal-Enclosed Power Switchgear Assemblies

IEEE Std C37.81-1989 1E级金属铠装电源开关设备组件的抗地震性鉴定指南

Provides requirements and guidance for the seismic qualification of metal-enclosed power switchgear assemblies including switching, interrupting, control, instrumentation, metering, and protective and regulating devices mounted therein.

Guide for seismic qualification of class 1E metal-enclosed power switchgear assemblies

CSA C22.2 No.156-M1987-1987(R2018) 固态速度控制

1. Scope 1.1 This Standard applies to solid-state, single-phase motor speed controls, rated at 300 V and less, 20 A and less, designed to be used in circuits for the control of shaded pole, permanent split capacitor, or universal motors, and other motors suitable for use with this type of control, intended for use in nonhazardous locations in accordance with the Canadian Electrical Code, Part I. 1.2 This Standard applies to controls that may incorporate a switch t o place an air gap in series with the motor; and when provided with a series switch, (a) incorporate solid-state components in a phase shift network to provide a controlled voltage output and designed so that (i) Type I: the ON/OFF function is independent of the output voltage setting; or (ii) Type II: the ON/OFF function can be operated at minimum output voltage setting only; or (iii) Type III: the ON/OFF function can be operated at maximum output voltage setting only; or (b) (Type IV) incorporate solid-state components to provide one or more, but not an infinite number of positions of control. 1.3 This Standard applies to controls intended for (a) flush mounting; (b) surface mounting; (c) use as a table-mounted control to which a portable motor can be temporarily connected; (d) installation in other equipment as part of the control package for that equipment; (e) permanent installation in the supply line of a motor; or (f) other similar applications within the general outline above. 1.4 This Standard does not apply to resistor, transformer, and variable frequency type motor speed controls.

Solid-State Speed Controls

IEEE Std C37.82-1987 核电站中1E级用开关设备组件的鉴定

Describes the methods and requirements for qualifying switchgear assemblies for indoor areas outside of the containment in nuclear power generating stations.

Qualification of switchgear assemblies for class 1E applications in nuclear power generating stations

ANSI/IEEE C37.82:1987 核电站中1E级设施用开关装置组件的合格鉴定标准

Describes the methods and requirements for qualifying switchgear assemblies for indoor areas outside of the containment in nuclear power generating stations.

Standard for the Qualification of Switchgear Assemblies for Class 1E Applications in Nuclear Power Generating Stations

IEEE Std C37.100B-1986 TRV 术语的定义；补充

Definitions for TRV Terms; Supplement

IEC 60129:1984 交流隔离开关和接地开关

Alternating current disconnectors and earthing switches

DIN 43660:1982 电气开关设备和控制设备的组合顺序

Modular order for electrical switchgear and controlgear installationsZusammenhang mit dem von der International Electrotechnical Commission (IEC) herausgegebenen Guide 103, 1. Ausgabe 1980, siehe Erl?uterungen.

Modular order for electrical switchgear and controlgear installations

CSA C22.2 No.31-1977 开关设备组件

Switchgear Assemblies

FprEN IEC 61800-9-2:2023 可调速电力驱动系统 (PDS) 第9-2部分：电机系统的生态设计 能效测定和分类

IEC 61800-9-2:2023 specifies energy efficiency indicators of power electronics (complete drive modules (CDM), input or output sub drive modules (SDM), power drive systems (PDS) and motor starters, all used for motor driven equipment. This document is a group energy efficiency publication according to IEC Guide 119 and specifies the methodology for the determination of losses of the complete drive module (CDM), the sub drive module (SDM), the power drive system (PDS) and the motor system. It defines IE and IES classes, their limit values and provides test procedures for the classification of the overall losses of the motor system. Furthermore, this document proposes a methodology for the implementation of the best energy efficiency solution of drive systems. This depends on the architecture of the motor driven system, on the speed/torque profile and on the operating points over time of the driven load equipment. It provides a link for the energy efficiency evaluation and classification of the extended product. This edition includes the following significant technical changes with respect to the previous edition: a) Additional IES Classes defined to IES5; b) Removed reference motor loss data and now point to IEC 60034-30-2; c) Expanded and modified factors in Clause 6 for CDMs; d) Annex C is now the Mathematical Model for CDM Losses; e) Moved the mathematical model for the CDM to Annex C; f) Added Sub Drive Input Module and Sub Drive Output Modules to Annex B; g) Annex D is now the Converter Topology (old Annex C); h) Annex E is now the Interpolation of Motor Losses (Old Annex D); i) Annex E expanded to include various motor connections and updated interpolation method; j) New Annex E for determination of Interpolation Coefficients; k) Annex F is the old Annex E; l) New Annex J Explanation of Correction Factors for the Reference Losses in Table 8.

Adjustable speed electrical power drive systems (PDS) - Part 9-2: Ecodesign for motor systems - Energy efficiency determination and classification

AS 2067:2016/V2 交流电压大于1 kV的开关设备组件和辅助设备

Specifies requirements for high voltage a.c. switchgear assemblies, indoor and outdoor, employed in connection with the generation, transmission and distribution of electric power and to ancillary equipment used in conjunction with the switchgear. Gives

Switchgear assemblies and ancillary equipment for alternating voltages above 1 kV

AS 2467:2008 电气开关设备的维护

This Standard sets out recommendations and procedures for the maintenance of electrical switchgear. It is applicable to electrical switchgear having rated voltages not greater than 145 V.

Maintenance of electrical switchgear

AS 2067:1984 交流电压大于1 kV的开关设备组件和辅助设备

Specifies requirements for high voltage a.c. switchgear assemblies, indoor and outdoor, employed in connection with the generation, transmission and distribution of electric power and to ancillary equipment used in conjunction with the switchgear. Gives

Switchgear assemblies and ancillary equipment for alternating voltages above 1 kV