29.130.20 低压开关装置和控制器 标准查询与下载

GSO IEC 60947-5-9:2015 低压切断、连接和控制装置 第5-9部分：控制电路装置和开关元件 流量控制开关

This part of IEC 60947 applies to flow rate switches that sense the rate of flow of a gas, a liquid or a granular solid. These switches change their output state if a pre-set value for the speed of flow is exceeded. These flow rate switches are self-contained, have semiconductor switching element(s) and are intended to be connected to circuits, the rated voltage of which does not exceed 250 V 50 Hz/60 Hz a.c. or 300 V d.c. This standard does not specify the additional measures that are necessary for flow rate switches used in conjunction with explosive sensing materials and/or in an explosive location. This standard is not intended to cover devices with analogue outputs. The object of this standard is to state for flow rate switches: – definitions; – classifications; – characteristics; – product information; – normal service, mounting and transport conditions; – constructional and performance requirements; – tests to verify rated characteristics.

Low-voltage switchgear and controlgear - Part 5-9: Control circuit devices and switching elements - Flow rate switches

GSO IEC 60947-7-1:2015 低压切割、连接和控制设备 零件号 (7-1)：附加设备 铜导体接线端子

This part of IEC 60947 specifies requirements for terminal blocks with screw-type or screwless-type clamping units primarily intended for industrial or similar use and to be fixed to a support to provide electrical and mechanical connection between copper conductors. lt applies to terminal blocks intended to connect round copper conductors, with or without special preparation, having a cross-section between 0,2 mm2 and 300 mm2 (AWG 24/600 kcmil), intended to be used in circuits of a rated voltage not exceeding 1000 V a.c. up to 1000 Hz or 1500 V d.c. NOTE AWG is the abbreviation of “American Wire Gage” (Gage (US) = Gauge (UK)) kcmil = 1000 cmil; 1 cmil = 1 circular mil = surface of a circle having a diameter of 1 mil 1 mil = 1/1 000 inchThis standard may be used as a guide for − terminal blocks requiring the fixing of special devices to the conductors, for example quick connect terminations or wrapped connections, etc.; − terminal blocks providing direct contact to the conductors by means of edges or points penetrating the insulation, for example insulation displacement connections, etc.; − special types of terminal blocks, for example with diodes or varistors or similar component holders, etc. Where applicable in this standard, the term “clamping unit” has been used instead of the term “terminal”. This is taken into account in case of reference to IEC 60947-1.

Low-voltage switchgear and controlgear - Part 7-1: Ancillary equipment - Terminal blocks for copper conductors

GSO IEC 60947-5-3:2015 低压切割、连接和控制设备 零件编号 (5-3)：控制电路装置以及连接和断开元件 对故障条件下具有规定行为的近似工具的要求

This part of IEC 60947 series provides additional requirements to those given in IEC 60947-5-2. It addresses the fault performance aspects of proximity devices with a defined behaviour under fault conditions (PDDB). It does not address any other characteristics that can be required for specific applications. This standard does not cover proximity devices with analogue output. This Standard does not deal with any specific requirements on acoustic noise as the noise emission of control circuit devices and switching elements is not considered to be a relevant hazard. For a PDDB used in applications where additional characteristics, dealt with in other standards, are required, the requirements of all relevant standards apply. The use of this standard alone does not demonstrate suitability for the implementation of any specific safety related functionality. In particular, this standard does not provide requirements for the actuation characteristics of a PDDB, or for means to reduce the effects of mutual interference between devices, e.g. coded targets. Therefore these and any other application-specific requirements will need to be considered in addition to the requirements of this standard. NOTE 1 Due to their behaviour under fault conditions, PDDBs can, for example, be used as interlocking devices (see ISO 14119). NOTE 2 The requirements for electro-sensitive protective equipment for the detection of persons are given in the IEC 61496 series.

Low-voltage switchgear and controlgear - Part 5-3: Control circuit devices and switching elements - Requirements for proximity devices with defined behaviour under fault conditions (PDDB)

GSO IEC 60947-5-6:2015 低压切断和控制设备 第（5-6）部分：控制电路装置和切断元件 接近探头和切断放大器的直流接口

This International Standard applies to proximity sensors connected for operation by a two-wire connecting cable to the control input of a switching amplifier. The switching amplifier contains a d.c. source to supply the control circuit and is controlled by the variable internal resistance of the proximity sensor. These devices can be used in an explosive atmosphere if they also comply with IEC 60079-11. NOTE These devices have been defined by the German organization “Normenausschuß für Meß- und Regelungstechnik (NAMUR)” (Office for Standardization of Measurement and Regulation Techniques).

Low-voltage switchgear and controlgear - Part 5-6: Control circuit devices and switching elements - DC interface for proximity sensors and switching amplifiers (NAMUR)

GSO IEC 60947-5-7:2015 低压切割、连接和控制设备 零件编号 (5-7)：控制电路仪表以及切割和连接元件 带模拟输出的接近仪表的要求

This part of IEC 60947 states the requirements for proximity devices with analogue output.They may consist of one or more parts. The requirements of IEC 60947-5-2 (proximity switches) apply with the additions or modifications as stated in this standard. The clause numbering in this standard follows the clause numbering of IEC 60947-5-2, modified where necessary.

Low-voltage switchgear and controlgear - Part 5-7: Control circuit devices and switching elements - Requirements for proximity devices with analogue output

DIN EN 60947-1:2015 低压开关设备和控制设备.第1部分:一般规则(IEC 60947-1-2007+A1-2010+A2-2014);德文版本EN 60947-1-2007+A1-2011+A2-2014

Low-voltage switchgear and controlgear - Part 1: General rules (IEC 60947-1:2007 + A1:2010 + A2:2014); German version EN 60947-1:2007 + A1:2011 + A2:2014

KS C IEC 61439-5-2015(2020) 低压开关柜和控制组件 - 第5部分:公共网络配电组件

Low-voltage switchgear and controlgear assemblies — Part 5: Assemblies for power distribution in public networks

KS C IEC 61439-5:2015 低压开关设备和控制设备配件.第5部分:公共网络配电用配件

Low-voltage switchgear and controlgear assemblies — Part 5: Assemblies for power distribution in public networks

IEC 60947-3:2008+AMD1:2012+AMD2:2015 CSV 低压开关设备和控制设备 第3部分 开关 隔离开关、隔离开关和熔断器组合装置

Low-voltage switchgear and controlgear - Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units

IEC 60947-3:2015 低压开关设备和控制设备第3部分:开关、隔离开关、隔离开关和熔断器组合装置

"Scope and object This part of IEC 60947 applies to switches@ disconnectors@ switch-disconnectors and fusecombination units to be used in distribution circuits and motor circuits of which the rated voltage does not exceed 1 000 V a.c. or 1 500 V d.c. The manufacturer shall specify the type@ ratings and characteristics according to the relevant standard of any incorporated fuses. This part does not apply to equipment coming within the scope of IEC 60947-2@ IEC 60947-4-1 and IEC 60947-5-1; however@ when switches and fuse-combination units coming into the scope of this part are normally used to start@ accelerate and/or stop an individual motor they shall also comply with the additional requirements given in Annex A. The requirements for single pole operated three pole switches are included in Annex C. Auxiliary switches fitted to equipment within the scope of this part shall comply with the requirements of IEC 60947-5-1. This part does not include the additional requirements necessary for electrical apparatus for explosive gas atmospheres. NOTE 1 Depending on its design@ a switch (or disconnector) can be referred to as ""a rotary switch (disconnector)""@ ""cam-operated switch (disconnector)""@ ""knife-switch (disconnector)""@ etc. NOTE 2 In this part@ the word ""switch"" also applies to the apparatus referred to in French as ""commutateurs""@ intended to modify the connections between several circuits and inter alia to substitute a part of a circuit for another. NOTE 3 In general@ throughout this part switches@ disconnectors@ switch-disconnectors and fuse-combination units will be referred to as ""equipment"". The object of this part is to state a) the characteristics of the equipment; b) the conditions with which the equipment shall comply with reference to 1) operation and behaviour in normal service; 2) operation and behaviour in case of specified abnormal conditions@ e.g. short circuit; 3) dielectric properties; c) the tests for confirming that these conditions have been met and the methods to be adopted for these tests; d) the information to be marked on the equipment or made available by the manufacturer@ e.g. in the catalogue."

Low-voltage switchgear and controlgear - Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units

IEC 60947-3:2008/AMD2:2015 低压开关装置和控制器.第3部分:开关、隔离器、开关隔离器和熔断器组合电器;修改件2

Low-voltage switchgear and controlgear - Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units; Amendment 2

BS PD IEC/TR 61641:2014 封闭式低压开关设备和控制设备组合装置. 因内部故障导致的起弧条件下进行试验指南

Enclosed low-voltage switchgear and controlgear assemblies. Guide for testing under conditions of arcing due to internal fault

EN 62026-3:2015 低压开关设备和控制设备.控制器接口(CDIs).第3部分:DeviceNet

IEC 62026-3:2014 specifies an interface system between single or multiple controllers, and control circuit devices or switching elements. The interface system uses two conductor pairs within one cable - one of these pairs provides a differential communication medium and the other pair provides power to the devices. This part establishes requirements for the interoperability of components with such interfaces. This third edition of IEC 62026-3 cancels and replaces the second edition published in 2008. This third edition constitutes a technical revision. The main changes with respect to the previous edition are the followings: - specification of group 4 messages (5.1.2); - clarifications on messaging protocol (5.2); - addition of I/O multicast poll messages (5.5.2 and 5.5.8); - clarifications on slave behaviour (5.5.4 and 5.5.9); - clarifications on physical layer (transceiver) in 5.7; - miscellaneous corrections/clarifications on cable (8.2); - clarifications on EMC testing (9.2.10) and logical testing (9.3).

Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 3: DeviceNet

DIN EN 60947-4-3:2015 低压开关设备和控制设备.第4-3部分:接触器和电动机起动器.非电动机负载用交流半导体控制器和接触器(IEC 60947-4-3-2014);德文版本EN 60947-4-3-2014

Low-voltage switchgear and controlgear - Part 4-3: Contactors and motor-starters - AC semiconductor controllers and contactors for non-motor loads (IEC 60947-4-3:2014); German version EN 60947-4-3:2014

DIN EN 61915-2:2015 低压开关设备和控制设备 联网工业设备的设备配置文件 第2部分：启动器和类似设备的根设备配置文件（IEC 61915-2:2011 + Cor.:2012）；英文版 EN 61915-2:2012

Low-voltage switchgear and controlgear - Device profiles for networked industrial devices - Part 2: Root device profiles for starters and similar equipment (IEC 61915-2:2011 + Cor.:2012); English version EN 61915-2:2012

IEC 62026-3:2014/COR1:2015 低压开关设备和控制设备.控制器-器件的接口(CDIs).第3部分:器件网络;勘误1

Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 3: DeviceNet

DIN EN 62026-2:2015 低压开关设备和控制设备 控制器设备接口（CDI） 第2部分：执行器传感器接口（AS-i）（IEC 62026-2:2008，已修改）；德文版 EN 62026-2:2013

Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 2: Actuator sensor interface (AS-i) (IEC 62026-2:2008, modified); German version EN 62026-2:2013

IEC 61439-5:2014/COR1:2015 低压开关设备和控制设备配件.第5部分:公共网络配电用配件;勘误1

Low-voltage switchgear and controlgear assemblies - Part 5: Assemblies for power distribution in public networks

DIN EN 60947-3 Berichtigung 1:2015 低压开关设备和控制设备. 第3部分:开关, 切断器, 开关切断器及熔断器组合装置 (IEC 60947-3-2008+A1-2012);德文版本EN 60947-3-2009+A1-2012;勘误1

Low-voltage switchgear and controlgear - Part 3: Switches, disconnectors, switchdisconnectors and fuse-combination units (IEC 60947-3:2008 + A1:2012); German version EN 60947-3:2009 + A1:2012, Corrigendum to DIN EN 60947-3 (VDE 0660-107):2012-12; (IEC-Cor

BS EN 61439-5:2015 低压开关装置和控制装置.公共网络配电用配件

Low-voltage switchgear and controlgear assemblies. Assemblies for power distribution in public networks