共找到 929 条与 荧光灯、放电灯 相关的标准,共 62 页
This Standard specifies the performance requirements for double-capped fluorescent lamps for general lighting service. The requirements of this standard relate only to type testing, Conditions of compliance, including methods of statistical assessment, are under consideration. For som of the requirements given in this standard, reference is made to ""the relevant lamp data sheet"". For some lamps these data sheets are contained in this standard. For other lamps, falling under the scope of this standard, the relevant data are supplied by the lamp manufacturer or responsible vendor.
Double-capped fluorescent lamps - Performance specifications
GLASS WARE FOR LIGHTING FITTING'S (DIMENSIONS FOR FITTED PORTIONS)
Specifies the characteristics of high-pressure sodium vapour lamps necessary to ensure interchangeability and safety together with test conditions and procedures. The recommendations relate only to type testing. Specifies the lamp dimensions, electrical
High-pressure sodium vapour lamps
Specifies the safety requirements for discharge lamps (excluding fluorescent lamps) for general lighting purposes. This International Standard is applicable to low-pressure sodium vapour lamps and to high-intensity discharge (HID) lamps, i.e. high-pressu
Discharge lamps (excluding fluorescent lamps) - Safety specifications
Test method on electromagnetic emissions from electronic ballast for single-and double-capped fluorescent lamps
Test method on electromagnetic emissions from electronic ballast for single-and double-capped fluorescent lamps
KS C CISPR 30은 기준 조명 기구에 의해 동작하는 1등급 형광 램프에 사용되는
Test method on electromagnetic emissions from electronic ballast for single-and double-capped fluorescent lamps
This standard is Discharge lamps (excluding fluorescent lamps) - Safety specifications; Amendment 1.
Discharge lamps (excluding fluorescent lamps) - Safety specifications; Amendment 1
Signs and luminous-discharge-tube installations operating from a no-load rated output voltage exceeding 1 kV but not exceeding 10 kV - Part 1: General requirements; German version EN 50107-1:2002
この規格は,一般照明用直管蛍光ランプの性能要求事項する。
Double-capped fluorescent lamps -- Part 2: Performance specifications
この規格は,一般照明用片口金蛍光ランプ(環形を含む)の性能要求事項を規定する。
Single-capped fluorescent lamps -- Part 2: Performance specifications
This International Standard specifies the performance requirements for double-capped fluorescent lamps for general lighting service. The requirements of this standard relate only to type testing. Conditions of compliance, including methods of statistical assessment, are under consideration. The following lamp types and modes of operation are included: a) lamps having preheated cathodes, designed for operation on a.c. mains frequencies with the use of a starter, and additionally operating on high frequency; b) lamps having preheated high-resistance cathodes, designed for operation on a.c. mains frequencies without the use of a starter (starterless), and additionally operating on high frequency; c) lamps having preheated low-resistance cathodes, designed for operation on a.c. mains frequencies without the use of a starter (starterless), and additionally operating on high frequency; d) lamps having preheated cathodes, designed for operation on high frequency; e) lamps having non-preheated cathodes, designed for operation on a.c. mains frequencies; f) lamps having non-preheated cathodes, designed for operation on high frequency. For some of the requirements given in this standard, reference is made to "the relevant lamp data sheet". For some lamps these data sheets are contained in this standard. For other lamps, falling under the scope of this standard, the relevant data are supplied by the lamp manufacturer or responsible vendor.
Double-capped fluorescent lamps - Performance specifications; Amendment 2
This standard is supplies specific instructions for size reduction of lamps including integral electronic compact, pin-based compact, linear and U-shaped fluorescent lamps.
Procedures for Fluorescent Lamp Sample Preparation and the Toxicity Characteristic Leaching procedure
Specifies performance requirements for single capped fluorescent lamps for general lighting service. This Standard is identical to and reproduced from IEC 60901:2001, that includes Amendment 1 and Amendment 2.
Single-capped fluorescent lamps - Performance specifications
This standard specifically covers high-intensity discharge lamp types. The procedures contained within are intended to supplement the Toxicity Characteristic Leaching Procedure by supplying specific instructions for size reduction and for other critical
Electric Lamps - Procedures for High Intensity Discharge Lamp - Sample Preparation and the Toxicity Characteristic Leaching Procedure
This standard is intended to cover performance of glow switch starters used with preheat-type fluorescent and similar discharge lamps. It does not include starters that are an integral part of a lamp or manually operated switches that may be used for lam
Specifications for Fluorescent Lamp Starters
이 규격은 국내용과 이와 유사한 일반 조명용으로서 시동과 안정한 동작을 위한 장치가 내장된
Self-ballasted lamps for general lighting services-Performance requirements
이 규격은 KS C 7610, KS C IEC 60192 및 KS C IEC 60662에서
Ballasts for sodium vapour lamps
Glow starters for fluorescent lamps
Transformer for tubular discharge lamps having a no-load output voltage exceeding 1000 V General and safety requirements
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号