共找到 1223 条与 有关灯的其他标准 相关的标准,共 82 页
Lamp controlgear -- Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules
Lamps for road vehicles - Performance requirements
This Technical Specification provides guidelines for establishing confidence in product reliability using principal component testing for LED light sources and LED luminaires for general lighting. It includes methods and criteria using initial qualification tests and accelerated stress tests of the principal components. The performance of any principal component will influence the performance of the final product. Techniques to validate full lifetime claims and lumen maintenance projection are outside the scope of this Technical Specification. The following principal components are included in the testing if they are used as an integral part for the LED light source or LED luminaire: LED package and interconnects; optical materials; electronic subassemblies; cooling systems, both active (e. g. fans) and passive (e. g. thermal interface material); construction materials. This Technical Specification is not recommended for use as a normative reference to the LED product performance standards.
Guidelines for principal component reliability testing for LED light sources and LED luminaires
Organic light emitting diode (OLED) panels for general lighting. Performance requirements
IEC 62922:2016 specifies the performance requirements of OLED tiles and panels for use on DC supplies up to 120 V or AC supplies up to 50 V at 50 Hz or 60 Hz for indoor and similar general lighting purposes.
Organic light emitting diode (OLED) panels for general lighting - Performance Requirements
Lamp controlgear -- Part 2-10: Particular requirements for electronic invertors and convertors for high-frequency operation of cold start tubular discharge lamps (neon tubes)
Lamp controlgear -- Part 1: General and safety requirements
This document specifies the safety and interchangeability requirements together with the test methods and conditions required to show compliance of non-integrated tubular LED lamps, intended for general lighting purposes, having: a rated wattage up to 70 W; a rated voltage up to 190 V ripple free DC; GX16t-5 cap as listed in Table 1. The requirements of this document relate only to type testing. NOTE 1 Where in this document the term "lamp(s)" is used, it is understood to stand for "non-integrated GX16t-5 capped tubular LED-lamp(s)", except where it is obviously assigned to other types of lamps. NOTE 2 The lamp specified in this document is operated with a controlgear specified in Annex B. See Clause 18. NOTE 3 This document includes photobiological safety.
GX16t-5 capped tubular led lamp - Safety specifications
This International Standard provides general and safety requirements for programmable components used in products covered by IEC 61347. The definition of "tolerable risk" needed to be corrected, because of a wrong reference on a clause for types of risks.
Programmable components in electronic lamp controlgear - General and safety requirements (IEC 62733:2015); German version EN 62733:2015, Corrigendum to DIN EN 62733 (VDE 0712-4):2016-03, (IEC 62733:2015/COR1:2017); German version EN 62733:2015/AC:2017-09
3.1 道路照明用LED灯具效能 efficacy of LED luminaire for road lighting 在标准规定的测试条件下,道路照明用LED灯具发出的初始总光通量与其所消耗的功率之比,单位为流明每瓦(lm/W)。 3.2 道路照明用LED灯具能效限定值 minimium allowable vaule of efficiency of LED luminaire for road lighting 在标准规定的测试条件下,道路照明用LED灯具效能应达到的
Allowable values of energy efficiency and energy efficiency grades of LED lamps for road lighting
Electrical interface specifications for self ballasted lamps and controlgear in phase-cut dimmed lighting systems
Auxiliaries for lamps - Capacitors for use in tubular fluorescent and other discharge lamp circuits - General and safety requirements (IEC 61048:2006 + A1:2015); German version EN 61048:2006 + A1:2016
This document specifies the electrical interface between phase-cut dimming equipment and lighting equipment, such as LED integrated lamps and light sources with external controlgear, with the intention of helping designers of both types of equipment to develop products that will work together properly. This document describes both the dimming phase and the off phase. In addition to the specification of the interface, test procedures are given for testing the proper operation. It may be expected that controlgear fulfilling the requirements of this document are also suited to be used with electronic switches that use a circuitry comparable with that of a phase-cut dimmer, but do not contain means for the adjustability of the phase-cut angle. Safety requirements are not covered by this document, but by respective product standards
Electrical interface specifications for self ballasted lamps and controlgear in phase-cut dimmed lighting systems
本标准规定了照明用LED驱动电源的基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存、质量承诺。 本标准适用于恒流或恒压型室内外照明用LED驱动电源。
LED driver for lighting
Self-ballasted LED lamps for general lighting services with supply voltages > 50 V - Performance requirements; Corrigendum 1
考核和确定产品在高温、低温环境条件下贮存和(或)使用的适用性
Test method for high and low temperature weather resistance of LED street lamps and tunnel lamps
本标准的适用于LED室内照明产品,通过可靠性强应力试验快速评价产品的重大缺陷。本标准试验方法不适用于寿命评估和估算
Rapid assessment method for major defects of LED indoor lighting products
额定电压不超过250V,额定频率50Hz,额定电流不超过16A的控制装置
General Technical Specifications for Indoor LED Lamp Intelligent Control System
液晶显示器用LED背光组件(以下简称“背光组件”)
Performance Requirements for LED Backlight Components
LED路灯和LED隧道灯
Simulation evaluation and calculation method of LED street lamp tunnel lighting application effect
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号