29.160.01 旋转电机综合 标准查询与下载

IEC 60034-11:2020 旋转电机 - 第11部分:热保护

Rotating electrical machines - Part 11: Thermal protection

IEC 60034-18-42:2017+AMD1:2020 CSV 旋转电机.第18-42部分:由电压转换器供电的旋转电机用抗局部放电电气绝缘系统（II型）.鉴定试验

Rotating electrical machines - Part 18-42: Partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters - Qualification tests

IEC 60034-18-42:2017/AMD1:2020 修改件1.旋转电机.第18-42部分:由电压转换器供电的旋转电机中使用的抗局部放电电气绝缘系统（II型）.鉴定试验

Amendment 1 - Rotating electrical machines - Part 18-42: Partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters - Qualific

KS C IEC 60034-12-2020 旋转电机 - 第12部分:单速三相笼式异步电动机的启动性能

Rotating electrical machines — Part 12: Starting performance of single-speed three-phase cage induction motors

KS C IEC 60034-12:2020 旋转电机 - 第12部分:单速三相笼式异步电动机的启动性能

Rotating electrical machines — Part 12: Starting performance of single-speed three-phase cage induction motors

EN IEC 60034-3:2020 旋转电机 第3部分：由蒸汽轮机或燃气轮机驱动的同步发电机和同步补偿器的特殊要求

IEC 60034-3:2020 applies to large three-phase synchronous generators, having rated outputs of 10 MVA and above driven by steam turbines or combustion gas turbines. Also included are synchronous Mvar compensators of the same output range connected to a grid for the purpose of exchanging reactive power. This document supplements basic requirements for rotating machines given in IEC 60034-1. This seventh edition cancels and replaces the sixth edition published in 2007. This edition includes the following significant technical changes with respect to the previous edition: - title modified; - scope extended to synchronous compensators; - rotor overcurrent requirements added; - impact of stator harmonics on rotor unbalanced load capability introduced; - synchronisation requirements added; - adjustments of temperatures or temperature rise revised for gas turbine applications; - requirements for auxiliaries updated.

Rotating electrical machines - Part 3: Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines and for synchronous compensators

BS EN IEC 60034-5:2020 旋转电机 旋转电机整体设计提供的防护等级（IP 代码） 分类

What is BS EN IEC 60034 ‑ 5 about?   BS EN IEC 60034 ‑ 5 discusses rotating electrical machines. It applies to the classification of degrees of protection provided by enclosures for rotating electrical machines.   BS EN IEC 60034 ‑ 5 defines the requirements for protective enclosures that are in all other respects suitable for their intended use and which, from the point of view of materials and workmanship, ensure that the properties dealt with

Rotating electrical machines - Degrees of protection provided by the integral design of rotating electrical machines (IP code). Classification

IEC 60034-3:2020 旋转电机第3部分:汽轮机或燃气轮机驱动的同步发电机和同步补偿器的特殊要求

Rotating electrical machines - Part 3: Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines and for synchronous compensators

EN IEC 60034-2-3:2020 旋转电机 第 2-3 部分：确定变流器供电交流电机损耗和效率的特定测试方法

IEC 60034-2-3:2020 specifies test methods and an interpolation procedure for determining losses and efficiencies of converter-fed motors within the scope of IEC 60034-1:2017. The motor is then part of a variable frequency power drive system (PDS) as defined in IEC 61800‑9‑2:2017. Applying the approach of the comparable converter, the motor efficiency determined by use of this document is applicable for comparison of different motor designs only. The document also specifies procedures to determine motor losses at any load point (torque, speed) within the base speed range (constant torque range, constant flux range) based on determination of losses at seven standardized load points. This procedure is applicable to any variable speed AC motor (induction and synchronous) rated according to IEC 60034-1:2017 for operation on a variable frequency and variable voltage power supply.

Rotating electrical machines - Part 2-3: Specific test methods for determining losses and efficiency of converter-fed AC motors

IEC 60034-5:2020 RLV 旋转电机.第5部分:旋转电机整体设计提供的防护等级（IP代码）.分类

Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification

IEC 60034-5:2020 旋转电机.第5部分:旋转电机整体设计提供的防护等级（IP代码）.分类

Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification

IEC 60034-2-3:2020 旋转电机 - 第2-3部分:确定变频器供电电动机的损耗和效率的具体测试方法

Rotating electrical machines - Part 2-3: Specific test methods for determining losses and efficiency of converter-fed AC motors

JB/T 10500.1-2019 电机用埋置式热电阻 第1部分：一般规定、测量方法和检验规则

Embedded thermal resistors for motors Part 1: General provisions, measurement methods and inspection rules

JB/T 10500.3-2019 电机用埋置式热电阻 第3部分：铜热电阻技术要求

Embedded thermal resistors for motors Part 3: Technical requirements for copper thermal resistors

JB/T 10500.2-2019 电机用埋置式热电阻 第2部分：铂热电阻技术要求

Embedded thermal resistors for motors Part 2: Technical requirements for platinum thermal resistors

JB/T 10415.2-2019 发电机液体内冷空心导线 第2部分：不锈钢空心导线

Generator liquid internal cooling hollow conductors Part 2: Stainless steel hollow conductors

T/CEC 234-2019 直流输电工程大型调相机组设备监造技术导则

本标准规定了直流输电工程大型调相机组设备在制造过程中的监造工作内容、监造工作程序和见证方式。 本标准适用于直流输电工程中容量在100Mvar及以上的调相机及其辅机设备的监造。其他调相机及其辅机设备可参照执行。

Technical Guidelines for Manufacturing Supervision of Large-Scale Phase Adjusting Units for DC Transmission Projects

EN 60034-18-41:2014/A1:2019 旋转电机 第 18-41 部分：用于由电压转换器供电的旋转电机的无局部放电电气绝缘系统（I 型） 鉴定和质量控制测试

The contents of the corrigendum of December 2020 have been included in this copy.

Rotating electrical machines - Part 18-41: Partial discharge free electrical insulation systems (Type I) used in rotating electrical machines fed from voltage converters - Qualification and quality control tests

T/WWDX 002-2019 YE3系列超高效率三相异步电动机技术条件

本标准是在GB/T 28575-2012《YE3系列高效率三相异步电动机技术条件（机座号80-355）》的基础改进而成的，本标准针对市场客户的实际情况，增加了电动机的外壳防护电机及电动机的额定功率，满足了不同的客户要求，在各个机座号下，对增加的功率给出的效率、功率因数、最大转矩倍数、最小转矩倍数、起动电流倍数。     本标准与GB/T 28575-2012《YE3系列高效率三相异步电动机技术条件（机座号80-355）的主要差异如下： ——增加了电动机的外壳防护等级IP55 ——增加了电动机的额定频率为50Hz

Technical conditions of YE3 series ultra-high efficiency three-phase asynchronous motors

T/WWDX 001-2019 YE2系列三相异步电动机技术条件

本标准是在JB/T 11707-2017《YE2系列三相异步电动机技术条件（机座号63～355）》的基础改进而成的，本标准针对市场客户的实际情况，增加了电动机的外壳防护等级及电动机的额定功率，满足了不同的客户要求，在每个机座号下，增加不同功率的效率、功率因数、最大转矩倍数、最小转矩倍数、起动电流倍数。 本标准与JB/T 11707-2017《YE2系列三相异步电动机技术条件（机座号63～355）》的主要差异如下： ——增加了电动机的外壳防护等级IP55

Technical conditions of YE2 series three-phase asynchronous motors