29.160.01 旋转电机综合 标准查询与下载

SANS 60034-4:2009 旋转电机．第4部分：同步电机参数的试验测定方法

Applies to three-phase synchronous machines of 1 kVA rating and larger, with rated frequency of not more than 500 Hz and not less than 10 Hz. Does not apply to axial-field machines and special synchronous machines such as inductor type machines and trans

Rotating electrical machines Part 4: Methods for determining synchronous machine quantities from tests

NF C51-350*NF EN 60034-15:2009 旋转电机.第15部分:交流旋转电机用成型绕组定子线圈的耐冲击电压水平

Rotating electrical machines - Part 15 : impulse voltage withstand levels of form-wound stator coils for rotating a.c. machines.

DIN EN 60034-4:2009 旋转电机.第4部分:测定同步电机特性参数的试验方法

Rotating electrical machines - Part 4: Methods for determining synchronous machine quantities from tests (IEC 60034-4:2008); German version EN 60034-4:2008

BS EN 60034-4:2008 旋转电机.通过试验测定同步机参量的方法

This part of IEC 60034 applies to three-phase synchronous machines of 1 kVA rating and larger with rated frequency of not greater than 500 Hz and not less than 10 Hz. Most of the methods are intended to be used for machines having an excitation winding with slip-rings and brushes for their supply. Synchronous machines with brushless excitation require special effort for some of the tests. For machines with permanent magnet excitation, there is a limited applicability of the described tests, and special precautions have to be taken against irreversible demagnetization. Excluded are axial-field machines and special synchronous machines such as inductor type machines and transversal flux machines. It is not intended that this standard be interpreted as requiring any or all of the tests described therein on any given machine. The particular tests to be carried out shall be subject to agreement between manufacturer and customer.

Rotating electrical machines - Methods for determining synchronous machine quantities from tests

BS EN 60034-4:2009 旋转电机 通过试验测定同步机参量的方法

Rotating electrical machines. Methods for determining synchronous machine quantities from tests

IEC 60034-15:2009 旋转电机.第15部分:带定子成型线圈的交流旋转电机的脉冲电压耐受等级

This part of IEC 34 specifies the rated phase-to-earth impulse voltage withstand levels of rotating a.c. machines having rated voltages from 3 kV to 15 kV inclusive and incorporating form-wound stator coils@ together with the test procedures and voltages to be applied to the main and interturn insulation of sample coils to prove the compliance of the machine.

Rotating electrical machines - Part 15: Impulse voltage withstand levels of form-wound stator coils for rotating a.c. machines

DIN EN 60034-29:2009 旋转电机.第29部分:等效加载和迭加技术.测定温升的间接试验

Rotating electrical machines - Part 29: Equivalent loading and superposition techniques - Indirect testing to determine temperature rise (IEC 60034-29:2008); German version EN 60034-29:2008

GOST R IEC 60034-2-1-2009 旋转发电机.第2-1部分:测试(不包含牵引车)中的损失与效率的标准测定方法

Rotating electrical machines. Part 2-1. Standart methods for determining losses and efficiency from tests (excluding mashines for traction vehicles)

SNI IEC 60034-14:2009 旋转电机. 第14部分:轴中心高56mm及以上电机的机械振动. 振动强度的测量、评价和限值

Rotating electrical machines - Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher - Measurement, evaluation and limits of vibration severity

ANSI/UL 1004-8-2009 变频器专用电动机的安全标准

UL proposes the first edition of UL 1004-8, Inverter Duty Motors.

Standard for Safety for Inverter Duty Motors

IEC 2/1537/DTS:2008 IEC/TS 60034-24:旋转电机.第24部分:旋转电机和轴承电流有源部件的电位故障在线探测和诊断.应用指南

IEC/TS 60034-24: Rotating electrical machines - Part 24: Online detection and diagnosis of potential failures at the active parts of rotating electrical machines and of bearing currents - Application guide

KS C IEC 60034-14-2008(2023) 旋转电机第14部分:轴高56mm及以上的某些机器的机械振动振动严重程度的测量、评定和限值

Rotating electrical machines－Part 14：Mechanical vibration of certain machines with shaft heights 56 mm and higher－Measurement, evaluation and limits of vibration severity

KS C IEC 60034-14-2008(2018) 旋转电机第14部分:轴高56mm及以上的机械振动振动烈度的测量、评定和限值

Rotating electrical machines－Part 14：Mechanical vibration of certain machines with shaft heights 56 mm and higher－Measurement, evaluation and limits of vibration severity

DS/EN 60034-4:2008 旋转电机 第4部分：通过测试确定同步电机数量的方法

This part of IEC 60034 applies to three-phase synchronous machines of 1 kVA rating and larger with rated frequency of not greater than 500 Hz and not less than 10 Hz.Most of the methods are intended to be used for machines having an excitation winding with slip-rings and brushes for their supply. Synchronous machines with brushless excitation require special effort for some of the tests. For machines with permanent magnet excitation, there is a limited applicability of the described tests, and special precautions have to be taken against irreversible demagnetization.Excluded are axial-field machines and special synchronous machines such as inductor type mac

Rotating electrical machines - Part 4: Methods for determining synchronous machine quantities from tests

DS/EN 60034-29:2008 旋转电机 第29部分：等效加载和叠加技术 确定温升的间接测试

This International Standard applies to machines covered by IEC 60034-1 when they cannot beloaded to a specific condition (rated or otherwise). It is applicable to both motors and generators.

Rotating electrical machines - Part 29: Equivalent loading and superposition techniques - Indirect testing to determine temperature rise

NF C51-114:2008 旋转电机.第4部分:根据试验测定同步机数值的方法

Rotating electrical machines - Part 4 : methods for determining synchronous machine quantities from tests.

BS EN 60034-29:2008 旋转电机.等效加载和迭加技术.测定温升的间接试验

This International Standard applies to machines covered by IEC 60034-1 when they cannot be loaded to a specific condition (rated or otherwise). It is applicable to both motors and generators.

Rotating electrical machines. Equivalent loading and superposition techniques. Indirect testing to determine temperature rise

DIN EN 60034-2-1:2008 旋转电机.第2-1部分:通过试验测定旋转电机损耗和效率的标准方法(不包括牵引车辆用电机)

Rotating electrical machines - Part 2-1: Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles) (IEC 60034-2-1:2007); German version EN 60034-2-1:2007

SANS 60034-29:2008 旋转电机.第29部分:等效负载及叠加技术-间接检测以确定温升

Applies to machines covered by IEC 60034-1 (published in South Africa as an identical adoption under the designation SANS 60034-1) when they cannot be loaded to a specific condition (rated or otherwise). Is applicable to both motors and generators.

Rotating electrical machines Part 29: Equivalent loading and superposition techniques - Indirect testing to determine temperature rise

NF C51-112:2008 旋转电机.第2-1部分:试验(不包括牵引车辆用电机)中损失和功效的测定用标准方法

Rotating electrical machines - Part 2-1 : standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles).