29.160.01 旋转电机综合 标准查询与下载

NF C51-124/A1:2007 旋转电机.第14部分:轴高56mm及以上的特定电机的机械振动.振动强度的测量、评定和限值

Rotating electrical machines - Part 14 : mechanical vibration of certain machines with shaft heights 56 mm and higher - Measurement, evaluation and limits of vibration severity.

BS EN 60034-28:2007 旋转电机.三相低压鼠笼式感应电动机等效电路图数量测定的试验方法

This part of IEC 60034 applies to three-phase low-voltage cage induction motors of frame numbers 56 to 400 as specified in IEC 60072-1. This standard establishes procedures to obtain values for elements of single phase equivalent circuit diagrams from tests and defines standard elements of these diagrams.

Rotating electrical machines - Test methods for determining quantities of equivalent circuit diagrams for three-phase low-voltage cage induction motors

DS/EN 60034-26:2007 旋转电机 第26部分：不平衡电压对三相笼型感应电动机性能的影响

This part of IEC 60034 describes the effects of unbalanced voltages on the performance ofthree-phase cage induction motors.

Rotating electrical machines - Part 26: Effects of unbalanced voltages on the performance of three-phase cage induction motors

SANS 60034-5:2007 旋转电机．第5部分：旋转电机总体设计的防护等级（IP代码）．分级

Applies to the classification of degrees of protection provided by enclosures for rotating electrical machines. Defines the requirements for protective enclosures that are in all other respects suitable for their intended use and which, from the point of

Rotating electrical machines Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification

DS/EN 60034-5/A1:2007 旋转电机 第5部分：旋转电机整体设计提供的防护等级（IP 代码） 分类

Gives definitions for standard degrees of protection provided by enclosures; protection of machines against harmful effects due to the ingress of water; protection of machines against ingress of solid foreign objects; Protection of persons against contact with or approach to live parts and against contact with moving parts. Gives designations for these protective degrees and tests to verify that the machines meet the requirements.

Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification

JB/T 10415.2-2007 发电机液体内冷空心导线 第2部分:不锈钢空心导线

JB/T 10415的本部分规定了发电机液体内冷不锈钢空心导线（简称空心导线）的技术要求、试验方法、检验规则及标志、包装和贮存。 本部分适用于发电机用液冷不锈钢拉制矩形空心导线。

Hollow conductors for liquid inner cooled generator Part 2: Stainless steel hollow conductors

JB/T 7608-2006 测量高压交流电机线圈介质损耗角正切试验方法及限值

本标准规定了测量旋转电机单个定子线圈（线棒）介质损耗角正切的试验方法及限值。 本标准适用于额定电压为6kV及以上的同步发电机、同步调相机和交流电动机的定子线圈（线棒）B级和F级绝缘介质损耗角正切测量试验。 本标准不适用于未固化的线圈（线棒）。

Test method for measuring loss tangent of high voltage alternating current dynamo coil and limit value

IEC 60034-14:2007 旋转电机.第14部分:轴高≥56mm 固定机械的机械振动.测量、评定和振动极限

This part of IEC 60034 specifies the factory acceptance vibration test procedures and vibration limits for certain electrical machines under specified conditions, when uncoupled from any load or prime mover. It is applicable to d.c. and three-phase a.c. machines, with shaft heights 56 mm and higher and a rated output up to 50 MW, at operational speeds from 120 min–1 up to and including 15 000 min–1. This standard is not applicable to machines mounted in situ, three-phase commutator motors, single-phase machines, three-phase machines operated on single-phase systems, vertical waterpower generators, turbine generators greater than 20 MW and machines with magnetic bearings or series-wound machines. NOTE For machines measured in situ refer to applicable parts of ISO 10816 and ISO 7919.

Rotating electrical machines - Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher - Measurement, evaluation and limits of vibration severity

GOST R 52776-2007 旋转电机.评定和性能

Rotating electrical machines. Rating and performance

GOST R IEC 60034-5-2007 旋转发电机.第5部分:旋转电机(IP码)的整合设计安全级别分类

Rotating electrical machines. Part 5. Classification of protection degrees provided by the integral design of rotating electrical machines (IP code)

JB/T 6517-2006 氢油水控制系统 技术条件

本标准规定了发电机用氢油水控制系统技术要求、检查试验方法、检查项目及供货成套性、标志、包装、运输与贮存。 本标准适用于冷却方式为氢气、水或两种冷却介质同时使用，进行间接或直接冷却发电机的氢气控制系统、密封油控制系统、绕组冷却水控制系统及其自动化元件。

Technical requirements of hydrogen, sealing oil and cooling water system

SANS 60034-26:2006 旋转电机．第26部分：不平衡电压对三相感应电动机性能的影响

Describes the effects of unbalanced voltages on the performance of three-phase cage induction motors.

Rotating electrical machines Part 26: Effects of unbalanced voltages on the performance of three-phase cage induction motors

IEC TS 60034-27:2006 旋转电机.第27部分:在旋转电机绝缘子绕组上的局部离线放电测量

This part of IEC 60034 which is a technical specification provides a common basis for – measuring techniques and instruments, – the arrangement of test circuits, – normalization and testing procedures, – noise reduction, – the documentation of test results, – the interpretation of test results with respect to partial discharge off-line measurements on the stator winding insulation of rotating electrical machines when tested with alternating voltages up to 400 Hz. This technical specification applies to rotating machines having bars or form wound coils with conductive slot coating. This is usually valid for machines with voltage rating of 6 kV and higher. The measurement methods described in this specification may also be applied to machines without conductive slot coating. However, results may be different and are not covered by this specification.

Rotating electrical machines - Part 27: Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines

IEC 60034-5:2006 旋转电机.第5部分:旋转电机整体设计防护等级(IP代码).分类

This International Standard applies to the classification of degrees of protection provided by enclosures for rotating electrical machines. It defines the requirements for protective enclosures that are in all other respects suitable for their intended use and which, from the point of view of materials and workmanship, ensure that the properties dealt with in this standard are maintained under normal conditions of use. This standard does not specify: • degrees of protection against mechanical damage of the machine, or conditions such as moisture (produced for example by condensation), corrosive dust and vapour, fungus or vermin; • types of protection of machines for use in a potentially explosive (dust, vapour) environment. In certain applications (such as agricultural or domestic appliances), more extensive precautions against accidental or deliberate contact may be specified. This standard gives definitions for standard degrees of protection provided by enclosures applicable to rotating electrical machines as regards the: a) protection of persons against contacts with or approach to live parts and against contact with moving parts (other than smooth rotating shafts and the like) inside the enclosure and protection of the machine against ingress of solid foreign objects; b) protection of machines against the harmful effects due to ingress of water. It gives designations for these protective degrees and tests to be performed to check that the machines meet the requirements of this standard.

Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification

JB/T 10596-2006 磁阻式步进电动机通用技术条件

Variable reluctance stepping moter general specification

IEC 2/1406/DTS:2006 旋转电机.第25部分:为电源转换器专门设计的交流电动机的设计和性能指南

IEC 60034-25, Ed. 1: Rotating electrical machines - Part 25: Guidance for the design and perfromance of a.c. motors specifically designed for converter supply

IEC 60034-26:2006 旋转电机.第26部分:不平衡电压对三相感应发动机性能的影响

This part of IEC 60034 describes the effects of unbalanced voltages on the performance of three-phase cage induction motors.

Rotating electrical machines - Part 26: Effects of unbalanced voltages on the performance of three-phase induction motors

IEC 2/1384/DTS:2006 IEC 60034-27-TS，编 1：旋转电机 第27部分：旋转电机定子绕组绝缘的离线局部放电测量

IEC 60034-27-TS, Ed. 1: Rotating electrical machines - Part 27: Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines

DIN IEC 60072-2:2006 旋转电机的尺寸及功率等级.第2部分:机座号:355～1000、凸缘号:1180～2360(IEC 60072-2-1990)

Dimensions and output series for rotating electrical machines - Part 2: Frame numbers 355 to 1000 and flange number 1180 to 2360 (IEC 60072-2:1990)

KS C IEC 61986-2006(2011) 旋转电机等效负载和超定位技术测定温升的间接试验

Rotating electrical machines－Equivalent loading and super－position techniques－Indirect testing to determine temperature rise