29.160.01 旋转电机综合 标准查询与下载

NF C51-286:2004 旋转电机.等效负载和叠加技术.测定温度升高的间接试验

Rotating electrical machines - Equivalent loading and super-position techniques - Indirect testing to determine temperature rise.

DS/EN 60034-14:2004 旋转电机 第14部分：轴高 56 mm 及更高的某些机器的机械振动 振动强度的测量、评估和限值

This part of IEC 60034 specifies the factory acceptance vibration test procedures and vibration limits for certain electrical machines under specified conditions, when uncoupled from any load or prime mover. It is applicable to d.c. and three-phase a.c. machines, with shaft heights 56 mm and higher and a rated output up to 50 MW, at operational speeds from 120 min up to and including 15 000/min. This standard is not applicable to machines mounted in situ, three-phase commutator motors, single-phase machines, three-phase machines operated on single-phase systems, vertical waterpower generators, turbine generators greater than 20 MW and machines with magnetic

Rotating electrical machines - Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher - Measurement, evaluation and limits of vibration severity

IEC 60034-1:2004 旋转电机.第1部分:额定值和性能

Is applicable to all rotating electrical machines except those covered by other IEC standards (for example, IEC 60349). Machines within the scope of this standard may also be subject to superseding, modifying or additional requirements in other IEC stand

Rotating electrical machines - Part 1: Rating and performance

IEC 60034-8/COR1:2004 旋转电机.第8部分:线端标志和旋转方向.修改件1

This part of IEC 60034 applies to a.c. and d.c. machines and specifies:a) rules for the identification of winding connection points;b) marking of winding terminals;c) direction of rotation;d) relationship between terminal markings and direction of rotation;e) terminal marking of auxiliary devices;f) connection diagrams of machines for common applications.Turbine type synchronous machines are excluded in this standard.

Rotating electrical machines - Part 8: Terminal markings and direction of rotation; Corrigendum 1

DS/EN 60034-18-21/A1:2004 旋转电机 第18部分：绝缘系统的功能评估 第 21 节：绕线绕组的测试程序 热评估和分类

This section of IEC 60034-18 gives test procedures for the thermal evaluation and classification of insulation systems used or proposed for use in wire-wound alternating current (a.c.) or direct current (d.c.) rotating electrical machines. The test procedures are comparative in that the performance of a candidate insulation system is compared to that of a reference insulation system with proven service experience.

Rotating electrical machines - Part 18: Functional evaluation of insulation systems - Section 21: Test procedures for wire-wound windings - Thermal evaluation and classification

DIN V VDE V 0530-23:2004 旋转电机.第23部分:旋转电机整修规范

Rotating electrical machines - Part 23: Specification for the refurbishing of rotating electrical machines (IEC/TS 60034-23:2003)

DS/IEC/TS 60034-23:2003 旋转电机 第23部分：旋转电机的翻新规范

This Technical Specification covers the activities necessary to ensure the satisfactory rewinding and refurbishment of all types and sizes of rotating electrical machines covered by IEC 60034, including: - determining cause of failure, where necessary; - determining the extent of refurbishment, as applicable; - defining revised performance, operating and ambient conditions, if required; - reviewing the original design, and undertaking redesign, if required; - proving the quality and performance of the refurbished machine. This specification does not supersede the requirements prescribed in IEC 60079-19 or elsewhere concerning the repair and overhaul for mac

Rotating electrical machines - Part 23: Specification for the refurbishing of rotating electrical machines

DS/EN 60034-5+Corr.1:2003 旋转电机 第5部分：旋转电机整体设计提供的防护等级（IP 代码） 分类

This International Standard applies to the classification of degrees of protection provided by enclosures for rotating electrical machines. It defines the requirements for protective enclosures that are in all other aspects suitable for their intended use and which, from the point of view of materials and workmanship, ensure that the properties dealt with in this standard are maintained under normal conditions of use. This standard does not specify: 1) degrees of protection against mechanical damage of the machine, or conditions such of moisture (produced for example by condensation), corrosive vapours, fungus or vermin; 2) types of protection of machines f

Rotating electrical machines - Part 5: Degrees of protection provided by integral design of rotating electrical machines (IP code) - Classification

SANS 60034-23:2003 旋转电机．第23部分：旋转电机整修规范

Covers the activities necessary to ensure the satisfactory rewinding and refurbishing of all types and sizes of rotating electrical machines covered by IEC 60034.

Rotating electrical machines Part 23: Specification for the refurbishing of rotating electrical machines

KS C 4201-2003 三相异步电动机特性测试方法

Testing methods of three-phase induction motor characteristics

NF C51-118:2003 旋转电机.第8部分:线端标记和旋转方向

Rotating electrical machines - Part 8 : terminal markings and direction of rotation.

IEC TS 60034-23:2003 旋转电机.第23部分:旋转电机的整修规范

This Technical Specification covers the activities necessary to ensure the satisfactory rewinding and refurbishment of all types and sizes of rotating electrical machines covered by IEC 60034, including: · determining cause of failure, where necessary; · determining the extent of refurbishment, as applicable; · defining revised performance, operating and ambient conditions, if required; · reviewing the original design, and undertaking redesign, if required; · proving the quality and performance of the refurbished machine. This specification does not supersede the requirements prescribed in IEC 60079-19 or elsewhere concerning the repair and overhaul for machines used in explosive atmospheres. Machines for special applications such as hermetic, submersible, nuclear, military, aviation or rail borne may have additional requirements which should be the subject of agreement between the refurbisher and user.

Rotating electrical machines - Part 23: Specification for the refurbishing of rotating electrical machines

KS C 4005-2002 感应电机直接在线（全电压）交流起动器的一般规则

GENEIRAL RULES FOR DIREC-ON-LINE (FULL-VOLTAGE) A.C.STARTERS FOR INDUCTION MOTORS

JB/T 6204-2002 高压交流电机定子线圈及绕组绝缘耐电压试验规范

本标准规定了2kV～24kV高压交流电机定子线圈及绕组绝缘对地耐电压试验的电压限值。 本标准适用于交流发电机、同步调相机和交流电动机定子线圈及绕组绝缘交、直流耐电压试验。

Specifications for withstand voltage test on stator coil and winding insulation of high voltage AC machines

KS C 4002-2002 旋转电机的一般规则

GENERAL RULES FOR ROTATING ELECTRICAL MACHINES

BS EN 60034-8:2002 电动旋转机器.接线端标志与旋转方向

This part of IEC 60034 applies to a.c. and d.c. machines and specifies: a) rules for the identification of winding connection points; b) marking of winding terminals; c) direction of rotation; d) relationship between terminal markings and direction of rotation; e) terminal marking of auxiliary devices; f) connection diagrams of machines for common applications. Turbine type synchronous machines are excluded in this standard.

Rotating electrical machines - Terminal markings and direction of rotation

IEC TS 60034-26/COR1:2002 旋转电机.第26部分:不平衡电压对三相感应电动机性能的影响.技术勘误1

Rotating electrical machines - Part 26: Effects of unbalanced voltages on the performance of three-phase induction motors

CSN EN 60034-1+A1+A2-2002 旋转电机．第1部分：等级和业绩

Rotating motor. Part 1: Rank and Performance

SJ 52147/1-2002 JTDY4系列稀土永磁低速同步电动机详细规范

Low speed synchronous motors,rare-earth magnet,series JTDY4,detail specification for

VDI/VDE 3680-2002 同步电机控制

This guideline is intended to create harmonized basis for the assessment of excitation and control equipment.

Control of synchronous machines