29.160.01 旋转电机综合 标准查询与下载

JB/T 8312.2-1996 小型异步电动机用工程塑料风罩技术条件（机座号63～160)

本标准规定了小型异步电动机用工程塑料风罩的结构型式、技术要求、试验方法和检验规则、标志、运输和贮存。 本标准适用于基本系列的小型异步电动机(机座号63～160)以及对风罩无特殊要求的一般用途的其它小型异步电动机用工程塑料风罩。

Engineering plastics fan housing used on small asynchronous motors. Technical specification (frame size: 63-160)

NF C51-114:1996 旋转电机.第4部分:根据试验测定同步电机数值的方法

Rotating electrical machines. Part 4 : methods for determining synchronous machine quantities from tests.

NF C51-118:1996 旋转电机.第8部分:旋转电机的线端标记与旋转方向

Rotating electrical machines. Part 8 : terminal markings and direction of rotation of rotating machines.

SANS 60034-19:1995 旋转电机．第19部分：在常规和整流器供电中直流电机的特定试验方法

Applies to d.c. machines of 1 kW rated output power and above on conventional and rectifier-fed supplies except those covered by other IEC standards. Establishes methods for determining characteristic quantities for conventional and rectifier-fed d.c. ma

Rotating electrical machines Part 19: Specific test methods for d.c. machines on conventional and rectifier-fed supplies

IEC TR2 60034-16-3:1996 旋转电机 第16部分:同步电机励磁系统 第3节:动态性能

Reviews the methods available for investigating the response characteristics of the synchronous machine with its closed loop excitation control. Description of typical response and performance characteristics as well as performance criteria are given.

Rotating electrical machines - Part 16: Excitation systems for synchronous machines - Section 3: Dynamic performance

MT 451-1995 煤矿用隔爆型低压三相异步电动机.安全性能通用技术规范

本标准规定了煤矿用隔爆型低压三相异步电动机的安全性能要求、试验方法和检验规则。 本标准适用于在具有甲烷爆炸危险的煤矿井下使用的、额定电压至1140V 的电动机(以下简称电动机)。

Flameproof low voltage three-phase asynchronous motors intended to be used in coal mines General technical specification for safety performance

DS/EN 60034-6:1995 旋转电机 第6部分：冷却方法（IC 代码）

Identifies circuit arrangements and movement methods of the coolant. Classifies methods of cooling and gives a designation system for them. Complete and simplified designations are defined.

Rotating electrical machines - Part 6: Methods of cooling (IC code)

DS/EN 60034-7:1995 旋转电机 第7部分：结构类型和安装布置的分类（IM 代码）

Gives two systems of classification: an alpha-numeric designation applicable to machines with endshield bearings and only one shaft extension (code I) and an all-numeric designation applicable to a wide range of types of machines (code II) including types covered by code I.

Rotating electrical machines - Part 7: Classification of types of construction and mounting arrangements (IM code)

IEC 60034-19:1995 旋转电机.第19部分:普通电源或整流电源供电直流电机的专门试验方法

Deals with specific test methods for conventional and rectifier-fed rotating d.c. machines.

Rotating electrical machines - Part 19: Specific test methods for d.c. machines on conventional and rectifier-fed supplies

NF C51-318-31:1995 旋转电机.第18部分:绝缘体系的功能评定.第31节:模绕绕组线的试验程序.机器的最在功率为50MVA电压为15kV的绝缘系统用的热测定和分类

Rotating electrical machines. Part 18 : functional evaluation of insulation systems. Section 31 : test procedures for form-wound windings. Thermal evaluation and classification of insulation systems used in machines up to and including 50 mva and 15 kv.

IEC 60034-4/AMD1:1995 旋转电机 第4部分:同步电机参数的试验测定方法 修改1

Changes the subclause numbered A5.1 to A5.2. Adds the new subclause A5.1.

Rotating electrical machines - Part 4: Methods of determining synchronous machine quantities from tests; Amendment 1

AS 4307.1:1995 转动电气机械．修理和检修．低压机械

Specifies minimum requirements and gives procedural guidance for the rewinding and rebuilding of rotating electrical machines of 180 W to 400 kW with a rated voltage not exceeding 1000 V a.c. or 1500 V d.c.

Rotating electrical machines - Repair and overhaul - Low voltage machines

IEC 60034-15:1995 旋转电机 第15部分:带定子成型线圈的交流旋转电机的冲击电压耐受水平

This technical specification deals with the steady-state operation of cage induction motors within the scope of IEC 60034-12, when fed from converters. It covers the operation over the whole speed setting range, but does not deal with starting or transient phenomena. Only indirect type converters are dealt with. This type comprises converters with impressed direct current in the intermediate circuit (current source converters) and converters with impressed d.c. voltage (voltage source converters), either of the block type or the pulse controlled type, without restriction on pulse number, pulse width or pulse frequency. For the purpose of this technical specification, a converter may include any type of electronic switching device, for example transistors (bipolar or MOSfet), IGBTs, thyristors, GTO-thyristors, etc. with analog or digital control electronics.

Rotating electrical machines - Part 15: Impulse voltage withstand levels of rotating a.c. machines with form-wound stator coils

IEC 60034-18-33:1995 旋转电机绝缘结构功能性评定 成型饶组试验规程 多因子功能性评定50MVA、15kV及以下电机绝缘结构热、电综合应力耐久性

本部分规定了在热、电均为主要老化因子的情况下绝缘结构多因子耐久性评定的试验规程。 本部分中的试验规程适用于50 MVA、15 kV及以下交流电机用或拟用的成型绕组绝缘结构，是对 比试验规程，即将待评绝缘结构与经运行经验证实的基准绝缘结构进行性能对比。本部分中描述的评 定不包含应力分级。

Rotating electrical machines - Functional evaluation of insulation systems - Test procedures for form-wound windings - Multifactor functional evaluation - Endurance under combined thermal and electrical stresses of insulation systems used in machines up t

SNI 04-3864-1995 带法兰旋转电机功能输出率与度数

Dimension and rated output of rotating electrical machinery with mounting flange, frame numbers 355 to 1000

JB/T 7576-1994 户内外防腐蚀旋转电机环境技术要求

本标准规定了电机的防护类型、使用环境条件等级和参数、技术要求、试验方法、检验规则及标志等。 本标准适用于户内、户外腐蚀环境固定使用的电机。

Environmental technical requirement for indoor and outdoor corrosionproof electric rotating motors

CNS 5740-1994 交流旋转电机之标幺值

本标准规定旋转交流电机之基本标么值。

Basic Per-Unit Quantities for Alternating-Current Rotating Machines

SANS 60072-3:1994 旋转电机尺寸和输出功率等级．第3部分：小功率装入式电动机．凸缘号BF10～BF50

Applies to small built-in motors such as those usually intended for use in control devices.

Dimensions and output series for rotating electrical machines Part 3: Small built-in motors - Flange numbers BF10 to BF50

SJ/T 10474-1994 磁盘驱动器用电动机通用技术条件

本标准规定了无刷直流电动机、步进电动机和音圈电动机(除需要分别说明外，以下简称电机)的通用技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于磁盘驱动器中的电机。 本标准应与磁盘驱动器用电机的专用技术条件一起使用。各类电机的具体技术指标及附加或特殊要求，在专用技术条件中规定。

Miniature motors for disk drive,General specification for

BS EN 60034-6:1994 旋转电机..冷却方法（IC 代码）

Identifies circuit arrangements and the methods of movement of coolant in rotating electrical machines, classifies the methods of cooling and gives a designation system for them.

Rotating electrical machines.. Methods of cooling (IC Code)