共找到 1719 条与 易爆环境用电气设备 相关的标准,共 115 页
Explosive atmospheres — Part 0: Equipment — General requirements
Explosive atmospheres — Part 31: Equipment dust ignition protection by enclosure “t”
Explosive atmospheres — Part 15: Equipment protection by type of protection “n”
Explosive atmospheres — Part 31: Equipment dust ignition protection by enclosure “t”
Explosive atmospheres — Part 15: Equipment protection by type of protection “n”
Explosive atmospheres — Part 18: Equipment protection by encapsulation “m”
Explosive atmospheres — Part 18: Equipment protection by encapsulation “m”
Workplace atmospheres — Part 1: Gas detectors —Performance requirements of detectors for toxic gases
Explosive atmospheres - Part 36: Non-electrical equipment for explosive atmospheres - Basic method and requirements - Technical Corrigendum 1 (ISO 80079-36:2016/Cor 1:2019)
IEC 60079-19:2019 gives instructions, principally of a technical nature, on the repair, overhaul, reclamation and modification of equipment designed for use in explosive atmospheres; it is not applicable to maintenance, other than when repair and overhaul cannot be disassociated from maintenance, neither does it give advice on cable entry systems which may require a renewal when the equipment is re-installed. This fourth edition cancels and replaces the third edition published in 2010 together with Amendment 1:2015. This edition constitutes a technical revision. The significance of the changes between IEC 60079-19, Edition 3 (2010), including Amendment 1 (2015), and IEC 60079-19, Edition 4 (2019) are defined in the foreword and cover minor and editorial changes, extension, and major technical changes.
Explosive atmospheres - Part 19: Equipment repair, overhaul and reclamation
What is ISO 80079 ‑ 20 ‑ 1 on Gas and vapour classification about? ISO 80079 ‑ 20 ‑ 1 is an international standard that covers various safety aspects for explosive atmosphere. ISO 80079 ‑ 20 ‑
Explosive atmospheres - Material characteristics for gas and vapour classification. Test methods and data
Mine flameproof electric vibrator
Explosive atmospheres — Part 36: Non-electrical equipment for explosive atmospheres — Basic method and requirements — Technical Corrigendum 1
Mining steel wire core conveyor belt flaw detection device
General technical conditions for coal mine natural fire beam tube monitoring system
Mine explosion-proof high voltage inverter
本标准规定了隔爆型变极多速三相异步电动机的术语和定义、型式与参数、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存及质量承诺。 本标准适用于中心高 160 mm~200 mm 的隔爆型变极多速三相异步电动机(以下简称电动机)。
Flame-proof variable-pole multi-speed three phase inuction motor
1 Domaine d’application 1.1 La présente norme porte sur l’équipement d’extraction d’huile végétale commercial et industriel destiné à être installé et utilisé à l’extérieur, dans des lieux (non classés) ordinaires et des lieux (classés) dangereux. En fonction de l’application, l’installation doit être conforme aux instructions d’installation du fabricant, ainsi qu’aux éléments suivants, le cas échéant : a) La norme CSA C22.1, Code canadien de l’électricité, Partie 1, la norme ULC-S4400, Sécurité des locaux, des bâtiments et de l’équipement utilisés pour la culture, la transformation et la production du cannabis, le Code national de prévention des incendies du Canada; et le code CSA B149.1, Code d’installation du gaz naturel et du propane; et b) La norme NFPA 70, National Electrical Code (NEC), l’International Fire Code (IFC), la norme NFPA 1, Fire Code, la norme NFPA 55 Compressed Gases and Cryogenic Fluids Code, et la norme NFPA 58, Liquefied Petroleum Gas Code. 1.2 L’équipement d’extraction d’huile végétale comprend les éléments suivants : a) Équipement préparatoire pour préparer les matières végétales à l’extraction de l’huile, y compris la coupe, le désensemencement, le séchage et le traitement; b) Extracteurs pour extraire l’huile de la matière végétale à l’aide de gaz de pétrole liquéfié (GPL), de butane, de propane, d’éthanol ou de pentane (solvants inflammables) et de dioxyde de carbone (CO2) [solvant non inflammable]; c) Cabines ou nacelles d’extraction pour entourer ou protéger l’équipement d’extraction d’huile végétale; et d) Équipement de post-traitement pour finaliser le processus d’extraction de l’huile végétale, comme des étuves à vide, des évaporateurs rotatifs et des pompes pour la récupération des solvants. 1.3 Ces équipements, ainsi que les systèmes constitués de n’importe quelle combinaison de ces équipements, servent à extraire les huiles des matières végétales conformément aux instructions du fabricant. 1.4 Les exigences de la présente norme ne touchent pas les caractéristiques ou les effets, notamment physiologiques, qui peuvent résulter de l’utilisation de cet équipement. 1.5 La présente norme ne s’applique pas non plus aux équipements présentant les risques d’inflammation suivants : a) Réactions exothermiques, y compris l’auto-inflammation des poussières; b) Étincelles générées mécaniquement (c.-à-d. intentionnellement); c) Flammes et gaz chauds (y compris les particules chaudes). 1.6 La présente norme ne s’applique pas aux moyens mécaniques pour extraire des huiles végétales qui n’utilisent pas de solvant. 1.7 La présente norme concerne le raccordement des contenants ou des sources de solvant externes avec l’équipement d’extraction d’huile végétale. Remarque : En soi, l’équipement renvoie notamment à l’appareillage, aux raccords, aux dispositifs et aux composants utilisés dans le cadre d’une installation ou en lien avec celle-ci.
Vegetable oil extraction equipment intended for installation and use in ordinary (unclassified) locations and hazardous (classified) locations
ISO/IEC 80079-20-1:2017 is published as a dual log standard and provides guidance on classification of gases and vapours. It describes a test method intended for the measurement of the maximum experimental safe gaps (MESG) for gas-air mixtures or vapour-air mixtures under normal conditions of temperature and pressure (20 °C, 101,3 kPa) so as to permit the selection of an appropriate group of equipment. This document also describes a test method intended for use in the determination of the auto-ignition temperature (AIT) of a vapour-air mixture or gas-air mixture at atmospheric pressure, so as to permit the selection of an appropriate temperature class of equipment. Values of chemical properties of materials are provided to assist in the selection of equipment to be used in hazardous areas. Further data may be added as the results of validated tests become available. The materials and the characteristics included in a table (see Annex B) have been selected with particular reference to the use of equipment in hazardous areas. The data in this document have been taken from a number of references which are given in the bibliography. These methods for determining the MESG or the AIT may also be used for gas-air-inert mixtures or vapour-air-inert mixtures. However, data on air-inert mixtures are not tabulated. Keywords: classification of gases and vapours, measurement of the maximum experimental safe gaps (MESG)
Explosive atmospheres - Part 20-1: Material characteristics for gas and vapour classification - Test methods and data (ISO/IEC 80079-20-1:2017, including Cor 1:2018)
Explosive atmospheres - Part 19: Equipment repair, overhaul and reclamation
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号