31.120 电子显示器件 标准查询与下载

KS C IEC 62341-1-1:2007 有机发光二极管(OLED)显示器.第1-1部分:通用规范

이 규격은 유기발광다이오드(OLED) 디스플레이를 위한 품목규격이다. 이 규격은 IECQ-

Organic light emitting diode (OLED) displays - Part 1-1 : Generic specification

DIN EN 61747-3:2007 液晶和固态显示器件.第3部分:液晶显示(LCD)屏.分规范

This sectional specification applies to liquid crystal cells of the segment type monochrome. It gives details of the quality assessment procedures, the inspection requirements, screening sequences, sampling requirements and test and measurement procedures required for the assessment of liquid crystal display cells.#,,#

Liquid crystal display devices - Part 3: Liquid crystal display (LCD) cells - Sectional specification (IEC 61747-3:2006); German version EN 61747-3:2006

DS/EN 61747-3-1:2007 液晶显示装置 第 3-1 部分：液晶显示（LCD）单元 空白详细规范

Defines assessment procedures in such a manner that electronic components released by one participating country as conforming with the requirements of an applicable specification are equally acceptable in all participating countries without the need for further testing.

Liquid crystal display devices - Part 3-1: Liquid crystal display (LCD) cells - Blank detail specification

NF C93-547-3*NF EN 61747-3:2007 液晶显示设备.第3部分:液晶显示(LCD)屏.分规范

Liquid crystal display devices - Part 3 : liquid crystal diplay (LCD) cells - Sectional specification.

CEA-2017.1-2007 便携式电子设备的串行通信协议

This standard was developed by the Consumer Electronics Association’s (CEA) Mobile Electronics Committee (R6).

Serial Communication Protocol for Portable Electronic Devices

BS EN 61747-3:2006 液晶显示装置.液晶显示(LCD)器件.分项规范

This sectional specification applies to liquid crystal cells of the segment type monochrome . It gives details of the quality assessment procedures, the inspection requirements, screening sequences, sampling requirements and test and measurement procedures required for the assessment of liquid crystal display cells. Instead of the qualification approval procedure, the capability approval procedure can be applied (see Clause 4 of IECQ 001002-3; however, at present the capability approval procedure for liquid crystal display cells is under consideration) for all products manufactured in a defined process. All the requirements of this specification remain valid, unless modified by the requirements set out in 4.7 of this standard.

Liquid crystal display devices - Liquid crystal display (LCD) cells - Sectional specification

KS C IEC 61747-6-3-2006(2016) 液晶显示器件第6－3部分:有源矩阵液晶显示模块的运动伪影测量

Liquid crystal display devices－Part 6－3：Motion artifact measurement of active matrix liquid crystal display modules

KS C IEC 61747-6-2-2006(2021) 液晶显示器件第6－2部分:液晶模块测量方法反射式

Liquid crystal display devices－Part 6－2：Measuring methods for liquid crystal modules－Reflective type

KS C IEC 61747-5-2-2006(2016) 液晶显示装置 - 5-2部分:有源矩阵液晶显示模块的视觉检查

Liquid crystal display devices - Part 5-2 : Visual inspection of active matrix liquid display modules

KS C IEC 61747-5-2-2006(2021) 液晶显示器件第5-2部分:有源矩阵液晶显示模块的目视检查

Liquid crystal display devices - Part 5-2 : Visual inspection of active matrix liquid display modules

KS C IEC 61747-6-3:2006 液晶显示器.第6-3部分:液晶显示模块测量方法.有源矩阵液晶显示模块的运动伪影测量

이 규격은 능동 액정 디스플레이 모듈 평가에 대한 일반적인 규격이다. 이 규격은 능동 액정

Liquid crystal display devices－Part 6－3：Motion artifact measurement of active matrix liquid crystal display modules

KS C IEC 61747-5-2:2006 液晶显示装置.第5-2部分:环境、耐久性和机械试验方法.有源矩阵彩色液晶显示模块的外观检查

이 규격은 액정 디스플레이 모듈에 관한 일반적인 표준이다. 이 규격은 칼라 능동 매트릭스

Liquid crystal display devices－Part 5－2：Visual inspection of active matrix liquid crystal display modules

KS C IEC 61747-6-2:2006 液晶和固态显示器件.第6-2部分:液晶显示模块的测量方法.反射类型

이 규격은 액정 디스플레이 모듈 평가에 요구되는 품질 평가 절차, 검사 요건, 선별 순서,

Liquid crystal display devices-Part 6-2:Measuring methods for liquid crystal modules-Reflective type

KS C IEC 61747-6-2-2006(2016) 液晶显示器件第6－2部分:液晶模组测量方法反射式

Liquid crystal display devices－Part 6－2：Measuring methods for liquid crystal modules－Reflective type

IEC 61747-3-1:2006 液晶显示器.第3-1部分:液晶显示屏(LCD).空白详细规范规范

International Standard IEC 61747-3-1 has been prepared by IEC technical committee 110: Flat panel display devices. This second edition cancels and replaces the first edition, published in 1998, and constitutes a technical revision. The main change with regard to the previous edition is as follows: – the new edition was editorially changed in accordance with current ISO/IEC directives. Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The QC number that appears on the front cover of this publication is the specification number in the IECQ Quality Assessment System for Electronic Components (IECQ). Future standards in this series will carry the new general title as cited above. Titles of existing standards in this series will be updated at the time of the next edition. A list of all parts of the IEC 61747 series, under the general title Liquid crystal display devices , can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication. At this date, the publication will be • reconfirmed, • withdrawn, • replaced by a revised edition, or • amended.

Liquid crystal display devices - Part 3-1: Liquid crystal display (LCD) cells - Blank detail specification

IEC 61747-3:2006 液晶显示器件.第3部分:液晶显示屏(LCD).分规范

This sectional specification applies to liquid crystal cells of the segment type monochrome . It gives details of the quality assessment procedures, the inspection requirements, screening sequences, sampling requirements and test and measurement procedures required for the assessment of liquid crystal display cells. Instead of the qualification approval procedure, the capability approval procedure can be applied (see Clause 4 of IECQ 001002-3; however, at present the capability approval procedure for liquid crystal display cells is under consideration) for all products manufactured in a defined process. All the requirements of this specification remain valid, unless modified by the requirements set out in 4.7 of this standard.

Liquid crystal display devices - Part 3: Liquid crystal display (LCD) cells - Sectional specification

DIN EN 61988-3-1:2006 等离子体显示板.第3-1部分:机械接口(IEC 61988-3-1-2005)

This part of DIN EN 61988 defines drawings and required dimensions of plasma display (PDP) modules, PDP components, PDP sub-assemblies and ancillary components.

Plasma display panels - Part 3-1: Mechanical interface (IEC 61988-3-1:2005); German version EN 61988-3-1:2005

DS/EN 61988-3-1:2006 等离子显示面板 第 3-1 部分：机械接口

This part of EN 61988 defines drawings and required dimensions of plasma display (PDP) modules, PDP components, PDP sub-assemblies and ancillary components. This standard serves as a basis to establish a set of PDP modules with a standard description of dimensions.

Plasma display panels - Part 3-1: Mechanical interface

CB 1381-2005 军用加固液晶显示器通用规范

本规范规定了军用加固液晶显示器（以下简称军用LCD）的要求、质量保证规定及交货准备等。 本规范适用于军用LCD的设计、制造和验收。

General specification for military rugged liquid crystal display

IEC 61988-3-1:2005 等离子体显示板.第3-1部分:机械接口

This part of IEC 61988 defines drawings and required dimensions of plasma display (PDP) modules, PDP components, PDP sub-assemblies and ancillary components. This standard serves as a basis to establish a set of PDP modules with a standard description of dimensions.

Plasma display panels - Part 3-1: Mechanical interface