共找到 256 条与 机电元件综合 相关的标准,共 18 页
IEC 60512-7-1:2010 when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to define a standard test method to assess the ability of a connector to withstand the impacts it would receive when dropped repeatedly.
Connectors for electronic equipment - Tests and measurements - Part 7-1: Impact tests (free connectors) - Test 7a: Free fall (repeated)
Electromechanical components for electronic equipment-Basic testing procedures and measuring methods-Part 12:Soldering tests-Section 6:Test 12f:Sealing against flux and cleaning solvents in machine so
Connectors for electronic equipment - Tests and measurements - Part 13-1: Mechanical operation tests - Test 13a: Engaging and separating forces (IEC 60512-13-1:2006)
Electromechanical components for electronic equipment-Basic testing procedures and measuring methods-Part 16:Mechanical tests on contacts and terminations-Section 20:Test 16t:Mechanical strength(wired
Electromechanical components for electronic equipment-Basic testing procedures and measuring methods-Part 13:Mechanical operating tests-Section 1:Test 13a:Engaging and separating forces
이 규격은 유동 및 고정 커넥터로 구성되는 4, 6 또는 8 접점의 8방향 커넥터 시스템을
Connectors for frequencies below 3MHz for use with printed boards-Part 7:Detail specification for connectors, 8-way, including fixed and free connectors with common mating features, with assessed quality
この規格は,電子機器用コネクタ(以下,コネクタという。)において,規定の炎及び振動の環境の下で最初の6分間,規定する電気的性能を満たし.かつ。試験中.コネクタを取り付けた耐火隔壁のなかへ炎が侵入するのを防いだ状態で,コネクタが20分間耐える能力を評価するための試験方法について規定する。
Electromechanical components for electronic equipment -- Basic testing procedures and measuring methods -- Part 20-2: Test 20b -- Flammability tests -- Fireproofness
この規格は,電子機器用コネクタ(以下,コネクタという。)を結合したときに導通するように設計されたコネクタのハウジング(シェル)間の抵抗を測定するための試験方法について規定する。
Connectors for electronic equipment -- Tests and measurements -- Part 2-6: Electrical continuity and contact resistance tests -- Test 2f: Housing (shell) electrical continuity
この規格は,電子機器用コネクタ(以下.コネクタという。)の能力を評価するための標準的試験方法について規定する。
Electromechanical components for electronic equipment -- Basic testing procedures and measuring methods -- Part 23-3: Test 23c: Shielding effectiveness of connectors and accessories
本标准规定了电力半导体器件用管芯定位环的型号、尺寸、技术要求、检验规则和包装、运输、贮存、标志等要求。 本标准适用于电力半导体器件用管芯定位环(以下简称定位环)。
Rings of dies of semiconductor devices
本标准规定了电力半导体器件用门极组合件的型号、尺寸、技术要求、检验规则和包装、运输、贮存、标志等要求。 本标准适用于电力半导体器件用门极组合件(以下称组合件)。
Components of gate terminal for power semiconductor devices
Electromechanical components for electronic equipment-Basic testing procedures and measuring methods-Part 5:Impact tests(free components), static load tests(fixed components), endurance tests and over
Electromechanical components for electronic equipment-Basic testing procedures and measuring methods-Part 23-3:Test 23c:Shielding effectiveness of connectors and accessories
Electromechanical components for electronic eqipment-Basic testing procedures and measuring methods-Part 2:General examination, electrical continuity and contact resistance tests, insulation tests and
Electromechanical components for electronic equipment-Basic testing procedures and measuring methods- Part 20-2:Test 20b-Flammability tests-Fireproofness
Electromechanical components for electronic equipment-Basic testing procedures and measuring methods-Part 19:Chemical resistance tests-Section 3:Test 19c-Fluid resistance
Connectors for electronic equipment-Tests and measurements-Part 11-9:Climatic tests-Test 11i:Dry heat
Electromechanical components for electronic equipment-Basic testing procedures and measuring methods-Part 11:Climatic tests-Section 7:Test 11g:Flowing mixed gas corrosion test
This part of IEC 60512 defines a standard test method, Test 11 g, to assess the effects of a controlled atmosphere polluted by gases at very low concentration on electrical contacts or connections.
Connectors for electronic equipment - Tests and measurements - Flowing mixed gas corrosion test
This part of IEC 60512 defines a standard test method for measuring the shielding effectiveness of a connector, or a connector fitted with an accessory and terminated with a cable. The complete assembly has a continuous 360 degrees shielding capability throughout its length. This test is suitable for measuring the shielding effectiveness of a connector fitted with triaxial contacts terminated with shielded, twisted pair cables as used in data bus systems.
Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 23-3: Test 23c: Shielding effectiveness of connectors and accessories
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号