33.120.20 导线和对称电缆 标准查询与下载

ANSI/CEA 803-B-2012 音频的和车辆安全/便利用移动电子布线符号

Mobile Electronics Wiring Designations for Audio, and Vehicle Security/Convenience

YD/T 2337-2011 通信电源用光伏电缆

本标准规定了太阳能通信电源用光伏电缆的要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于连接太阳能通信电源光伏组件之间、电池陈列之间及陈列于光伏逆变器直流端之间直流额定电压为1.8kV、交流额定电压U/U为0.6/1 kV的电缆。

Photovoltaic cables for electric powers in communication system

DS/IEC/TR 61156-1-3:2011 用于数字通信的多芯和对称对/四芯电缆 第 1-3 部分：使用对称对/四芯电缆对电缆组件进行建模的电气传输参数

This technical report is a supplement to the following standard: IEC 61156-1 Edition 3 (2007):Multicore and symmetrical pair/quad cables for digital communications – Part 1: Generic specification.This technical report covers the following topics following this standard:– the Near-end crosstalk test methods and length correction procedures of 6.3.5.– the Far-end crosstalk test methods and length correction procedures of 6.3.6.– the concatenation of cable measured segments, even if they are of different designThe final objective of this technical report is to describe the mathematics involved to model the concatenation of cable sections of different length, n

Multicore and symmetrical pair/quad cables for digital communications - Part 1-3: Electrical transmission parameters for modelling cable assemblies using symmetrical pair/quad cables

YD/T 2320-2011 通信用铜包铝电源线

本标准规定了交流额定电压600/1000V及以下通信用铜包铝电源线的分类与命名、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于通信局（站）、建筑物等电源输、配电系统中的通信用铜包铝电源线。

Copper clad aluminum power wires for communications

YD/T 2282-2011 通信设备用3GHz及以下频段对称电缆技术条件

本标准规定了通信设备用3GHz及以下频段对称电缆的要求、试验方法、检验规则、标志和包装等要求。 本标准适用于工作频率在3GHz及以下的通信设备模块间和设备之间的高速互连对称电缆。

Technical requirements for symmetrical cables at and below 3GHz used in telecommunication equipment

IEC TR 61156-1-3:2011 数字通信用多芯对称对绞/四芯电缆第1-3部分:使用对称对绞/四芯电缆模拟电缆组件的电气传输参数

Multicore and symmetrical pair/quad cables for digital communications - Part 1-3: Electrical transmission parameters for modelling cable assemblies using symmetrical pair/quad cables

YD/T 1173-2010 通信电源用阻燃耐火软电缆

本标准规定了通信电源用阻燃耐火软电缆的分类与命名、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于通信局站及建筑物等电源输、配电系统中的通信电源用阻燃耐火软电缆。

Flame-retardant and fire resistant flexible cable for power supply system for telecommunications

YD/T 2162-2010 铜包铝芯聚烯烃绝缘铝塑综合护套 市内通信电缆

本标准规定了铜包铝芯聚烯烃绝缘铝塑综合护套市内通信电缆的分类与命名、要求、试验方法、检验规则、标志以及包装。 本标准适用于传输音频信号、150kHz及以下的模拟信号和1024kbit/s及以下的数字信号的铜包铝芯聚烯烃绝缘铝塑综合护套市内通信电缆。在应用于宽带传输时，也可传输16Mbit/s以下的数字信号。

Local communication cables with copper-clad aluminum wire,solid polyolefin insulate,aluminum-plastic integrated sheath

DS/IEC 61156-2-1:2010 数字通信用多芯和对称对/四芯电缆 第 2-1 部分：水平地板布线 空白详细规范

This blank detail specification relates to multicore and symmetrical pair/quad cables for digitalcommunications in horizontal floor wiring.This blank detail specification determines the layout and style for detail specifications describing multicore and symmetrical pair(s)/quad(s) cables for digital communication in horizontal floor wiring. Detail specifications based on the blank detail specification may be prepared by a national standards organization, a manufacturer or a user.

Multicore and symmetrical pair/quad cables for digital communications - Part 2-1: Horizontal floor wiring - Blank detail specification

DS/EN 61935-2:2010 平衡和同轴信息技术布线测试规范 第2部分：ISO/IEC 11801 和相关标准中指定的软线

IEC 61935-2:2010 provides methods to ensure compatibility of balanced cords to be used in cabling according to ISO/IEC 11801 and provides test methods and associated requirements to demonstrate the performance and reliability of these balanced cords during their operational lifetime. This International Standard may also be used for providing test methods for assessing the behaviour of other balanced cords. This third edition cancels and replaces the second edition published in 2005. It differs from the second edition in that it covers category 6A to category 7A cords as defined in ISO/IEC 11801.

Specification for the testing of balanced and coaxial information technology cabling - Part 2: Cords as specified in ISO/IEC 11801 and related standards

GSO IEC 61156-1:2010 数字通信用多芯和对称双芯/四芯电缆 第1部分：通用技术规范

IEC 61156-1 is applicable to communication systems such as ISDN, local area networks and data communication systems and specifies the definitions, requirements and test methods of multicore, symmetrical pair and quad cables. It is also applicable to cables used for customer premises wiring. The contents of the corrigendum of August 2015 have been included in this copy.

Multicore and symmetrical pair/quad cables for digital communications - Part 1: Generic specification

GSO IEC 61935-3:2010 同轴和平衡 IT 电缆连接的测试 第3部分：ISO/IEC 15018 及相关规范中所述的复合电缆连接

IEC 61935-3:2008 specifies conformance testing for home cabling. These conformance tests include visual inspection, verification testing and either qualification testing or certification testing. Documentation for the test results are also specified.

Testing of balanced and coaxial information technology cabling - Part 3: Installed cabling as specified in ISO/IEC 15018 and related standards

BS DD IEC/PAS 61156-1-4:2010 数字通信用多芯对称配对/四芯电缆.传送特性小于等于1000 MHz的对称配对/四芯电缆.基于IEEE 802.3标准的有限动力传送用捆绑数据级别电缆的导体升温

Multicore and symmetrical pair/quad cables for digital communications. Symmetrical pair/quad cables with transmission characteristics up to 1000 MHz. Conductor heating of bundled data grade cables for limited power transmission based on IEEE 802.3

DS/IEC 61156-2:2010 数字通信用多芯和对称对/四芯电缆 第2部分：传输特性高达 100 MHz 的对称对/四芯电缆 水平地板布线 分规范

This sectional specification relates to IEC 61156-1:2002. The cables are specifically intendedfor horizontal floor wiring as defined in ISO/IEC 11801:1995.This specification defines individually screened or unscreened pair/quad cables, with or withoutoverall common screen for horizontal floor wiring. These cables are suitable for the various communication systems for which the reference is given in the relevant detail specification.The cables covered by this sectional specification are intended to operate with voltages and currents normally adopted for communication systems. These cables should not be connected to low impedance sources, for example, the pub

Multicore and symmetrical pair/quad cables for digital communications - Part 2: Symmetrical pair/quad cables with transmission characteristics up to 100 MHz - Horizontal floor wiring - Sectional specification

IEC 61156-2-1:2010 数字通信用对绞或星绞多芯对称电缆.第2-1部分:水平楼板布线.空白详细规范

This blank detail specification relates to multicore and symmetrical pair/quad cables for digital communications in horizontal floor wiring. This blank detail specification determines the layout and style for detail specifications describing multicore and symmetrical pair/quad cables for digital communication in horizontal floor wiring. Detail specifications based on the blank detail specification may be prepared by a national standards organization, a manufacturer or a user.

Multicore and symmetrical pair/quad cables for digital communications - Part 2-1: Horizontal floor wiring - Blank detail specification

IEC PAS 61156-1-4:2010 数字通信用对绞或星绞对称电缆.第4-1部分:传输特性1000 MHz以下的数字通信用对绞或星绞对称电缆.基于IEEE 802.3的极限输电用导体加热的成束基准标高电缆

This PAS is a technical supplement to IEC 61156-1, edition 3 (2007): Multicore and symmetrical pair/quad cables for digital communications – Part 1: Generic specification. This PAS, covering exclusively four-pair data grade cables, is intended to provide a test method for the determination of the maximum attained conductor temperatures which occur due to the deployment of the IEEE protocol for PoE /PoEP. It gives as well the required background information about the thermodynamic behaviour of such bundled cables, if they are located in areas with restricted heat dissipation, a reality which occurs in every installation situation. However, only the basic principles are given, as the rigorous application and solution of these problems fall into the relevant cabling standards.

Multicore and symmetrical pair/quad cables for digital communications – Part 1-4: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz – Conductor heating of bundled data grade cables for limited power transmission based on IEEE

DS/IEC 61156-6:2010 数字通信用多芯和对称对/四芯电缆 第6部分：传输特性高达 1 000 MHz 的对称对/四芯电缆 工作区布线 分规范

This part of IEC 61156 makes reference to IEC 61156-1. The cables decribed herein are intended primarily for work area wiring as defined in ISO /IEC 11801 and ISO/IEC 24702.It covers individually screened, common screened and unscreened pairs or quads. The transmission characteristics and the frequency range (see Table 1) of the cables are specified at 20 deg. C.These cables can be used for various communication channels which use as many as four pairs simultaneously. In this sense, this sectional specification provides the cable characteristics required by systems developers to evaluate new systems.The cables covered by this standard are intended to operat

Multicore and symmetrical pair/quad cables for digital communications - Part 6: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz - Work area wiring - Sectional specification

DS/EN 61935-2-20:2010 符合 EN 50173 系列的平衡通信电缆测试 第 2-20 部分：跳线和工作区线 D 类应用的空白详细规范

IEC 61935-2-20:2008(E) describes work area cord for class D applications, as defined in ISO/IEC 11801 as well as in the ISO/IEC 24702. It determines the layout and style for detail specifications describing cords with transmission characteristics up to 100 MHz for digital communications. Detail specifications, based on this blank detail specification, may be prepared by a national organization, a manufacturer, or a user. It cancels and replaces the ISO/IEC PAS 61935-2-20 published in 2007. It constitutes a technical revision.

Testing of balanced communication cabling in accordance with series EN 50173 - Part 2-20: Patch cords and work area cords - Blank detail specification for class D applications

IEC 61156-2:2010 数字通信用对绞或星绞多芯对称电缆.第2部分:传输特性100 MHZ及以下的对绞或星绞电缆.水平层布线.分规范

This sectional specification relates to IEC 61156-1:2002. The cables are specifically intended for horizontal floor wiring as defined in ISO/IEC 11801:1995. This specification defines individually screened or unscreened pair/quad cables, with or without overall common screen for horizontal floor wiring. These cables are suitable for the various communication systems for which the reference is given in the relevant detail specification. The cables covered by this sectional specification are intended to operate with voltages and currents normally adopted for communication systems. These cables should not be connected to low impedance sources, for example, the public mains electricity supply.

Multicore and symmetrical pair/quad cables for digital communications - Part 2: Symmetrical pair/quad cables with transmission characteristics up to 100 MHz - Horizontal floor wiring - Sectional specification

DIN VDE 0816-3 Berichtigung 2:2010 电信和数据处理系统用室外电缆.纸绝缘电缆.技术勘误DIN VDE 0816-3 (VDE 0816-3)-1988

External cables for telecommunication and data processing systems - Paper insulated cables, Corrigendum to DIN VDE 0816-3 (VDE 0816-3):1988-02