33.120.20 导线和对称电缆 标准查询与下载

IEC 61156-3:2003 数字通信用对绞或星绞多芯对称电缆.第3部分:工作区布线电缆.分规范

This sectional specification relates to IEC 61156-1. The cables are specifically intended for work area wiring as defined in ISO/IEC 11801. It covers individually unscreened pairs in cables for work area wiring. The cables may be provided with a common screen over the cable core. These cables are suitable for the various communication systems for which the reference is given in the appropriate detail specification. The cables covered by this sectional specification are intended to operate with voltages and currents normally adopted for communication systems. These cables should not be connected to low impedance sources, for example, the public mains electricity supply. The recommended temperature range during installation and operation may be indicated in the detail specification. NOTE 1 The nominal characteristics impedance of a cabling link, measured according to IEC 61156-1 should be 100 ?O120 O or 150 O at frequencies between 1 MHz and the highest specified frequency for the cabling category. NOTE 2 The attenuation should not be higher by more than 50 % for each respective category. NOTE 3 The resistance may be 20 % higher than the resistance of the corresponding category.

Multicore and symmetrical pair/quad cables for digital communications - Part 3: Work area wiring; Sectional specification

IEC 61156-3-1:2003 数字通信用对绞或星绞多芯对称电缆.第3-1部分:工作区布线电缆.空白详细规范

Determines the layout and style for detail specifications describing multicore and symmetrical pair(s)/quad(s) cables for digital communication in work area wirin. Detail specifications based on the blank detail specification may be prepared by a nationa

Multicore and symmetrical pair/quad cables for digital communications - Part 3-1: Work area wiring; Blank detail specification

IEC 61156-2-1:2003 数字通信用对绞或星绞多芯对称电缆.第2-1部分:水平平面布线.空白详细规范

Determines the layout and style for detail specifications describing multicolore and symmetrical pair(s)/quad(s) cables for digital communication in horizontal floor wiring. Detail specifications based on the blank detail specification may be prepared by

Multicore and symmetrical pair/quad cables for digital communications - Part 2-1: Horizontal floor wiring; Blank detail specification

IEC 61156-2:2003 数字通信用对绞或星绞多芯对称电缆.第2部分:水平平面布线.分规范

Covers individually screened and unscreened pairs or quads in cables having less than 20 pairs/10 quads for horizontal floor wiring. The cables may be provided with a common screen over the cable core. These cables are suitable for the various communicat

Multicore and symmetrical pair/quad cables for digital communications - Part 2: Horizontal floor wiring; Sectional specification

IEC 61156-4:2003 数字通信用对绞或星绞多芯对称电缆.第4部分:引上电缆.分规范

This sectional specification relates to IEC 61156-1. The cables are specifically intended for horizontal floor wiring as defined in ISO/IEC 11801. It covers individually unscreened 20 pairs/10 quads or more for vertical shafts or vertically between floors. When installed vertically extra length requirements may be applicable and are defined in the appropriate specifications. The cables may be provided with a common screen over the cable core. These cables are suitable for the various communication systems for which the reference is given in the appropriate detail specification. The cables covered by this sectional specification are intended to operate with voltages and currents normally adopted for communication systems. These cables should not be connected to low impedance sources, for example, the public mains electricity supply. The recommended temperature range during installation and operation may be indicated in the detail specification.

Multicore and symmetrical pair/quad cables for digital communications - Part 4: Riser cables; Sectional specification

UL 444 BULLETINS-2003 8/7/2003（2p）

1 This standard applies to 60-250°C single- or multiple-conductor jacketed or unjacketed, integral or nonintegral cables and single or multiple coaxial cables for telephone and other communication circuits such as voice, data, and audio for on-premise customer systems. These cables ale not prohibited from containing one or more optical fibre members. For the purpose of this standard, a coaxial cable or coaxial member conductor is a single conductor with a shield. For the purpose of this standard, a single- or multiple-conductor unjacketed cable is a cross-connect wire. 2 This standard applies to communications cables that are intended primarily for installation in accordance with Section 60 of the Canadian Electrical Code (CEC), Part 1, and Article 800 of the National Electrical Code (NEC) . They are rated for 300 V applications but are not so marked.

8/7/2003 (2p)

ANSI/ICEA S-85-625-2002 空芯聚烯烃绝缘铜导体通信电缆的技术要求

The purpose of this Standard is to establish generic technical requirements that may be referenced by individual telecommunications cable specifications covering products intended for normal outside plant use. The parameters covered provide material, construction, and performance requirements that are applicable to aircore, polyolefin insulated and jacketed cables of all pair counts, including a variety of shield and jacket combinations and optional compartmental screening

Aircore, Polyolefin Insulated, Copper Conductor Telecommunications Cable – Technical Requirements

ANSI/ICEA S-84-608-2002 聚烯烃绝缘填充铜导线通信电缆的技术要求

Establishes generic technical requirements that may be referenced by individual telecommunications cable specifications covering products intended for normal outside plant use. The parameters covered provide material, construction, and performance requirements that are applicable to filled, polyolefin insulated and jacketed cables of all pair counts, including a variety of shield and jacket combinations and optional compartmental screening

Telecommunications Cable Filled, Polyolefin Insulated, Copper Conductor – Technical Requirements

DS/EN 62012-1:2002 用于恶劣环境中的数字通信用多芯和对称对/四芯电缆 第1部分：通用规范

This part of 62012 specifies the definitions and test methods, when used in harsh environment, of symmetrical pair and quad cables used in digital communication systems such as ISDN, local area networks and data communication systems. This standard gives guidance concerning the design and testing of these cables.

Multicore and symmetrical pair/quad cables for digital communications to be used in harsh environments - Part 1: Generic specification

IEC 61156-1:2002 数字通信用对绞或星绞多芯对称电缆.第1部分:总规范

Is a guide to indoor cables which specifies the definitions and requirements of multicore, symmetrical pair and quad cables used in digital communication systems such as ISDN, local area networks and data communication systems.

Multicore and symmetrical pair/quad cables for digital communication - Part 1: Generic specification

BS EN 62012-1:2002 在条件恶劣环境中数字通信用两芯/四芯电缆.总规范

This part of IEC 62012 specifies the definitions and test methods, when used in harsh environment, of symmetrical pair and quad cables used in digital communication systems such as ISDN, local area networks and data communication systems. This standard gives guidance concerning the design and testing of these cables.

Multicore and symmetrical pair/quad cables for digital communications to be used in harsh environments - Generic specification

DIN VDE 0816-3 Berichtigung 1:2002 DIN VDE 0816-3 技术勘误 (VDE 0816 Teil 3):1988-02

Corrigenda to DIN VDE 0816-3 (VDE 0816 Teil 3):1988-02

DIN VDE 0816-1 Berichtigung 1:2002 DIN VDE 0816-1 技术勘误 (VDE 0816 Teil 1):1988-02

Corrigenda to DIN VDE 0816-1 (VDE 0816 Teil 1):1988-02

DS/IEC 61156-6-2:2002 数字通信用多芯和对称对/四芯电缆 第 6-2 部分：传输特性高达 600 MHz 的对称对/四芯电缆 工作区布线 能力批准 分规范

This part of IEC 61156 applies to Capability Approval requirements for cables intended to construct patch, equipment, and work area cords for digital communications in accordance with generic specification IEC 61156-1-1 and Clause 4 of the sectional specification IEC 61156-6. Clause 2 refers to the content of the Capability Manual. Clause 3 refers to the related quality layout. Clause 4 is related to the maintenance of the Capability Approval.

Multicore and symmetrical pair/quad cables for digital communications - Part 6-2: Symmetrical pair/quad cables with transmission characteristics up to 600 MHz - Work area wiring - Capability approval - Sectional specification

DS/IEC 61156-5-2:2002 数字通信用多芯和对称对/四芯电缆 第 5-2 部分：传输特性高达 600 MHz 的对称对/四芯电缆 水平地板布线 能力批准 分规范

This part of IEC 61156 applies to Capability Approval requirements for cables for digital communications in horizontal floor wiring in accordance with generic specification IEC 61156-1-1 and lause 4 of the sectional specification IEC 61156-5. Clause 2 refers to the content of the Capability Manual. Clause 3 refers to the Quality Plans. Clause 4 is related to the maintenance of the Capabillity Approval.

Multicore and symmetrical pair/quad cables for digital communications - Part 5-2: Symmetrical pair/quad cables with transmission characteristics up to 600 MHz - Horizontal floor wiring - Capability approval - Sectional specification

LST EN 50289-1-7-2002 通讯电缆 测试方法规范 第 1-7 部分：电气测试方法 传播速度

Communication cables. Specifications for test methods. Part 1-7: Electrical test methods. Velocity of propagation

LST EN 50289-1-5-2002 通讯电缆 测试方法规范 第 1-5 部分：电气测试方法 电容

Communication cables. Specifications for test methods. Part 1-5: Electrical test methods. Capacitance

LST EN 50289-1-4-2002 通讯电缆 测试方法规范 第 1-4 部分：电气测试方法 绝缘电阻

Communication cables. Specifications for test methods. Part 1-4: Electrical test methods. Insulation resistance

LST EN 50289-1-3-2002 通讯电缆 测试方法规范 第 1-3 部分：电气测试方法 介电强度

Communication cables. Specifications for test methods. Part 1-3: Electrical test methods. Dielectric strength

LST EN 50289-1-2-2002 通讯电缆 测试方法规范 第 1-2 部分：电气测试方法 直流电阻

Communication cables. Specifications for test methods. Part 1-2: Electrical test methods - DC resistance