33.120.20 导线和对称电缆 标准查询与下载

LST EN 50289-1-1-2002 通讯电缆 测试方法规范 第 1-1 部分：电气测试方法 一般要求

Communication cables. Specifications for test methods. Part 1-1: Electrical test methods. General requirements

LST EN 50289-1-8-2002 通讯电缆 测试方法规范 第 1-8 部分：电气测试方法 衰减

Communication cables. Specifications for test methods.- Part 1-8: Electrical test methods. Attenuation

LST EN 50289-1-9-2002 通讯电缆 测试方法规范 第 1-9 部分：电气测试方法 不平衡衰减（纵向转换损耗、纵向转换传输损耗）

Communication cables. Specifications for test methods. Part 1-9: Electrical test methods. Unbalance attenuation (longitudinal conversion loss, longitudinal conversion transfer loss)

DIN EN 50289-1-11:2002 通信电缆.试验方法规范.第1-11部分:电气试验方法.特性阻抗、输入阻抗、回路损耗; 德文版本 EN 50289-1-11:2001

The document details the test methods to determine the characteristic impedance, input impedance and return loss of cables used in analogue and digital communication systems.#,,#

Communication cables - Specifications for test methods - Part 1-11: Electrical test methods; Characteristic impedance, input impedance, return loss; German version EN 50289-1-11:2001

DIN EN 50289-1-10:2002 通信电缆.试验方法规范.第1-10部分:电气试验方法.串音; 德文版本 EN 50289-1-10:2001

The document details the test methods to determine the crosstalk cables used in analogue and digital communication systems.

Communication cables - Specifications for test methods - Part 1-10: Electrical test methods; Crosstalk; German version EN 50289-1-10:2001

DS/EN 50289-1-2:2002 通信电缆 测试方法规范 第 1-2 部分：电气测试方法 直流电阻

This Part 1-2 of EN 50289 details the test methods to determine the DC resistance characteristics of the conductors of cables used in analogue and digital communication systems. These characteristics are described by the conductor resistance, loop resistance and resistance unbalance. It is to be read in conjunction with Part 1-1 of EN 50289, which contains essential provisions for its application.

Communication cables - Specifications for test methods - Part 1-2: Electrical test methods - DC resistance

DS/EN 50289-1-3:2002 通信电缆 测试方法规范 第 1-3 部分：电气测试方法 介电强度

This Part 1-3 of EN 50289 details the test methods to verify the dielectric strength of the insulation of the finished cables used in analogue and digital communication systems. It is to be read in conjunction with Part 1-1 of EN 50289, which contains essential provisions for its application.

Communication cables - Specifications for test methods - Part 1-3: Electrical test methods - Dielectric strength

DS/EN 50289-1-1:2002 通信电缆 测试方法规范 第 1-1 部分：电气测试方法 一般要求

The series of Part 1 of the European Standard EN 50289 specifies the electrical test methods for cables used in analogue and digital communication systems.

Communication cables - Specifications for test methods - Part 1-1: Electrical test methods - General requirements

IEC 62012-1:2002 在条件恶劣环境中数字通信用对绞/星绞多芯和对称电缆.第1部分:总规范

GB／T 21204的本部分规定了在严酷环境下使用时对绞或星绞多芯对称电缆的定义和试验方法， 这种电缆用于数字通信系统，如综合业务数字网(1SDN)、局域网和数据通信系统。本部分是这类电缆 的设计和试验的导则。

Multicore and symmetrical pair/quad cables for digital communications to be used in harsh environments Part 1: Generic specification (Edition 1.0)

IEC 61156-5-2:2002 数字通信用对绞/星绞多芯和对称电缆.第5-2部分:不高于600MHz的有传输特性的对绞/星绞对称电缆.水平地板布线.鉴定能力.分规范

This part of IEC 61156 applies to Capability Approval requirements for cables for digital communications in horizontal floor wiring in accordance with generic specification IEC 61156-1-1 and Clause 4 of the sectional specification IEC 61156-5. Clause 2 refers to the content of the Capability Manual. Clause 3 refers to the Quality Plans. Clause 4 is related to the maintenance of the Capability Approval. NOTE Quality assessment belongs to the negotiation between customers and manufacturers. The following clauses are intended to be a guide when there is a request for a third-party Capability Approval. However, it may also be used as the basis for second-party or self-certification.

Multicore and symmetrical pair/quad cables for digital communications - Part 5-2: Symmetrical pair/quad cables with transmission characteristics up to 600 MHz; Horizontal floor wiring; Capability approval; Sectional specification

IEC 61156-6-2:2002 数字通信用对绞/星绞多芯和对称电缆.第6-2部分:不高于600MHz的有传输特性的对绞/星绞对称电缆.工作场所布线.鉴定性能.分规范

This part of IEC 61156 applies to Capability Approval requirements for cables intended to construct patch, equipment, and work area cords for digital communications in accordance with generic specification IEC 61156-1-1 and Clause 4 of the sectional specification IEC 61156-6. Clause 2 refers to the content of the Capability Manual. Clause 3 refers to the related quality layout. Clause 4 is related to the maintenance of the Capability Approval. NOTE Quality assessment belongs to the negotiation between customers and manufacturers. The following clauses are intended to be a guide when there is a request for a third-party Capability Approval. However, it may also be used as the basis for second-party or self-certification.

Multicore and symmetrical pair/quad cables for digital communications - Part 6-2: Symmetrical pair/quad cables with transmission characteristics up to 600 MHz; Work area wiring; Capability approval; Sectional specification

IEC 61156-5-1:2002 数字通信用对绞/星绞多芯和对称电缆.第5-1部分:不高于600MHz的有传输特性的对绞/星绞对称电缆.水平地板布线.空白详细规范

This blank detail specification describes symmetrical pair/quad cables intended to be used in digital communication systems such as ISDN, local area networks and data communication systems in horizontal floor wiring, using frequencies up to 600 MHz. This specification should be used in conjunction with IEC 61156-1 and IEC 61156-5. The blank detail specification determines the layout and style for detail specifications describing symmetrical pair/quad cables with transmission characteristics up to 600 MHz for digital communications. Detail specifications, based on the blank detail specification, may be prepared by a national organization, a manufacturer, or a user. The designation "Category 5e" is used herein to describe an enhanced Category 5 cable (see 1.1 of IEC 61156-5).

Multicore and symmetrical pair/quad cables for digital communications - Part 5-1: Symmetrical pair/quad cables with transmission characteristics up to 600 MHz; Horizontal floor wiring; Blank detail specification

IEC 61156-6-1:2002 数字通信用对绞/星绞多芯和对称电缆.第6-1部分:不高于600MHz的有传输特性的对绞/星绞对称电缆.工作场所布线.空白详细规范

This blank detail specification describes symmetrical pair/quad cables intended to construct patch, equipment, and work area cords in digital communication systems such as ISDN, local area networks and data communication systems using frequencies up to 600 MHz. This specification should be used in conjunction with IEC 61156-1 and IEC 61156-6. The blank detail specification determines the layout and style for detail specifications describing symmetrical pair/quad cables with transmission characteristics up to 600 MHz for digital communications. Detail specifications, based on the blank detail specification, may be prepared by a national organization, a manufacturer, or a user. The designation "Category 5e" is used herein to describe an enhanced Category 5 cable (see 1.1 of IEC 61156-6).

Multicore and symmetrical pair/quad cables for digital communications - Part 6-1: Symmetrical pair/quad cables with transmission characteristics up to 600 MHz; Work area wiring; Blank detail specification

DS/EN 50289-1-7:2002 通信电缆 测试方法规范 第 1-7 部分：电气测试方法 传播速度

Part 1-7 of EN 50289 details the test methods to determine the velocity of propagation of the finished cables used in analogue and digital communication systems. It is to be read in conjunction with Part 1-1 of EN 50289, which contains essential provisions for its application.

Communication cables - Specifications for test methods - Part 1-7: Electrical test methods - Velocity of propagation

DS/EN 50289-1-10:2002 通信电缆 测试方法规范 第 1-10 部分：电气测试方法 串扰

Part 1-10 of EN 50289 details the test methods to determine the crosstalk cables used in analogue and digital communication systems. Crosstalk effects are near end crosstalk (NEXT), far end crosstalk (FEXT), equal level far end crosstalk(ELFEXT), attenuation to crosstalk ratio (ACR) and power sum of crosstalk (PS). It is to be read in conjunction with Part 1-1 of EN 50289, which contains essential provisions for its application.

Communication cables - Specifications for test methods - Part 1-10: Electrical test methods - Crosstalk

DS/EN 50290-2-22:2002 通信电缆 第 2-22 部分：通用设计规则和结构 PVC 护套化合物

This part 2-22 of EN 50290 gives specific requirements for PVC sheathing compounds used for communication cables. It is to be read in conjunction with Part 2-20 of EN 50290.

Communication cables - Part 2-22: Common design rules and construction - PVC sheathing compounds

DS/EN 50289-1-9:2002 通信电缆 测试方法规范 第 1-9 部分：电气测试方法 不平衡衰减（纵向转换损耗、纵向转换传输损耗）

Part 1-9 of EN 50289 details the test methods to determine the attenuation of converted common mode signals into differential mode signals due to balance characteristics of cables used in analogue and digital communication systems by using the transmission measurement method. The terms related to this attenuation are defined in 3.1, 3.2 and 3.3. It is to be read in conjunction with Part 1-1 of EN 50289, which contains essential provisions for its application.

Communication cables - Specifications for test methods - Part 1-9: Electrical test methods - Unbalance attenuation (longitudinal conversion loss, longitudinal conversion transfer loss)

DS/EN 50289-1-11:2002 通信电缆 测试方法规范 第 1-11 部分：电气测试方法 特性阻抗、输入阻抗、回波损耗

This Part 1-11 of EN 50289 details the test methods to determine the characteristic impedance, input impedance and return loss of cables used in analogue and digital communication systems. It is to be read in conjunction with Part 1-1 of EN 50289, which contains essential provisions for its application.

Communication cables - Specifications for test methods - Part 1-11: Electrical test methods - Characteristic impedance, input impedance, return loss

DS/EN 50289-1-5:2002 通信电缆 测试方法规范 第 1-5 部分：电气测试方法 电容

Part 1-5 of EN 50289 details the test methods to determine the capacitance characteristics of the finished cables used in analogue and digital communication systems. It is to be read in conjunction with Part 1-1 of EN 50289, which contains essential provisions for its application.

Communication cables - Specifications for test methods - Part 1-5: Electrical test methods - Capacitance

DS/EN 50289-1-4:2002 通信电缆 测试方法规范 第 1-4 部分：电气测试方法 绝缘电阻

Part 1-4 of EN 50289 details the test methods to determine the insulation resistance of the finished cables used in analogue and digital communication systems. It is to be read in conjunction with Part 1-1 of EN 50289, which contains essential provisions for its application.

Communication cables - Specifications for test methods - Part 1-4: Electrical test methods - Insulation resistance