导线和对称电缆标准-分析测试百科网

GSO IEC/TR 61156-1-3:2014 用于数字通信的多芯和对称双绞线/四绞线电缆第1-3部分：使用对称双绞线/四绞线电缆建模电缆组件的电气传输参数

This technical report is a supplement to IEC 61156-1 Edition 3 (2007): Multicore and symmetrical pair/quad cables for digital communications – Part 1: Generic specification. This technical report covers the following topics following this standard: – the near-end crosstalk test methods and length correction procedures of 6.3.5; – the far-end crosstalk test methods and length correction procedures of 6.3.6; – the concatenation of measured cable segments, even if they are of different design. The final objective of this technical report is to describe the mathematics involved to model the concatenation of cable sections of different length, not based upon measurements but based upon the specification limits of the cables involved. This is required as a base foundation of the complete channel modelling, involving also the connectivity covered by IEC SC48B towards channels, as required and requested by ISO/IEC JTC1/SC25 WG3 for incorporation into ISO/IEC 11801:2002 [1] 1. This TR is informative and contains observations and recommendations applicable to using the length correction formulas for either measurements or modelling of balanced cables.

Multicore and symmetrical pair/quad cables for digital communications - Part 1-3: Electrical transmission parameters for modelling cable assemblies using symmetrical pair/quad cables

ICS: 33.120.20
CCS
发布: 2014-12-25
实施

GSO IEC 61156-5:2014 用于数字通信的多芯和对称双绞线/四绞线电缆第5部分：传输特性高达 1 000 MHz 的对称双绞线/四绞线电缆水平地板布线剖面规范

IEC 61156-5:2009(E) describes the cables intended primarily for horizontal floor wiring as defined in ISO/IEC 11801. It covers individually screened, common screened and unscreened pairs or quads. The transmission characteristics and the frequency range of the cables are specified at 20 °C. Those cables are intended to be used to support the delivery of low voltage and power applications such as IEEE 802.3af (Power over Ethernet) and IEEE 802.3at (Power over Ethernet Plus). This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - new requirements for new Cat6A and Cat7A cables; - revised requirements and tests for Cat5e, Cat6 and Cat7 cables. The contents of the corrigendum of February 2010 have been included in this copy. This publication is to be read in conjunction with IEC 61156-1:2002.

Multicore and symmetrical pair/quad cables for digital communications - Part 5: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz - Horizontal floor wiring - Sectional specification

ICS: 33.120.20
CCS
发布: 2014-12-25
实施

DIN EN 50407-3:2014 高比特率数字存取电信网络用多组电缆. 第3部分: 支持IP上多达100 Mbit/s的通用服务, xDSL和应用程序的最大连接长度为100 m的多达100 MHz的室内多组/四立管电缆; 德文版本EN 50407-3-2014

Multi-pair cables used in high bit rate digital access telecommunications networks - Part 3: Indoor multi-pair/quad riser cables up to 100 MHz for maximum length of connection 100 m supporting universal services, xDSL and applications up to 100 Mbit/s ove

ICS: 33.120.20
CCS: K13
发布: 2014-12
实施

IEC TR 62839-1:2014 环境声明.第1部分:电线电缆和附件产品.特殊规则

"This part of IEC 62839 specifies the PSR (product specific rules) for wires and cables used for communication@ data@ control and command. This PSR covers the use@ installation and end-of-life stages and provides methodological precisions to PEP/PCR writing for ""wires and cables and accessories"" products used for communication@ data@ control and command. PSR and general rules all together form the product category rules. ISO 14025:2006 establishes the principles and specifies the procedures for developing Type III environmental declaration programmes and Type III environmental declarations. It specifically establishes the use of the ISO 14040 series of standards in the development of Type III environmental declaration programmes and Type III environmental declarations. It establishes principles for the use of environmental information@ in addition to those given in ISO 14020:2000. Type III environmental declarations as described in ISO 14025:2006 are primarily intended for use in business-to-business communication@ but their use in business-to-consumer communication under certain conditions is not precluded. These environmental declarations@ referred here after as PEP@ follow a specific set of rules and requirements specified in product category rules declaration that are referred here after as ""PEP/PCR"". Three categories of wires and cables are covered: - communication and data wires and cables@ which may have metal or optical fiber conductors; - control and command wires and cables @ which can have metal or fiber optical conductors; - accessories. This document only deals with the ""wires and cables"" products. ""Accessories products"" are for further study. This document is primarily intended for: - environment and/or product managers; - LCA (life cycle assessment) experts in companies@ in charge of PEP/PCR development; - verifiers in charge of PEP/PCR conformity assessment in accordance with the defined rules."

Environmental declaration - Part 1: Wires, cables and accessory products - Specific rules

ICS: 33.120.20
CCS
发布: 2014-11-06
实施: 2014-11-08

YD/T 2740.2-2014 无线通信室内信号分布系统.第2部分:电缆(含漏泄电缆)技术要求和测试方法

本部分规定了无线通信室内分布系统用通信电缆的性能要求、试验方法、检验规则及标志、包装、运输和储存条件等技术要求。本部分适用于无线通信系统共用或独立建设的无线通信室内分布系统中所使用的通信电缆，包括用于室内分布系统信号延伸的中继频段电缆和射频覆盖工作频段的电缆：水平对绞电缆、皱纹铜外导体同轴电缆、编织外导体同轴电缆和漏泄电缆。

Indoor signal distributing system.Part 2: Technical requirement and test method of cable (Including leaky coaxial cable)

ICS: 33.120.20
CCS: M42
发布: 2014-10-14
实施: 2014-10-14

YD/T 2761-2014 通信电源用交联聚烯烃绝缘电缆

本标准规定了通信电源用交联聚烯烃绝缘电缆(以下简称电缆)的产品标记、要求、试验方法、检验规则、包装、运输和储存。本标准适用于通信枢纽、通信局站、数据中心及通信设备内部电源配电系统用、额定电压为600V/1000V及以下的通信电源用无卤低烟交联聚烯烃绝缘电缆。

Cross-linked polyolefin insulated cables for electric powers in communication system

ICS: 33.120.20
CCS: M42
发布: 2014-10-14
实施: 2014-10-14

KS C IEC 61935-3:2014 平衡和同轴信息技术布线测试第3部分：ISO/IEC 15018 和相关标准规定的已安装布线

이 표준은 가정용 케이블링의 적합성 시험에 대한 내용을 다룬다. 이 적합성 시험들은 외관검사, 검증시험 및 품질 시험이나 인증 시험을 포함한다. 시험결과에 대한 양식도 규정한다.

Testing of balanced and coaxial information technology cabling — Part 3: Installed cabling as specified in ISO/IEC 15018 and related standards

ICS: 33.120.20
CCS
发布: 2014-10-03
实施: 2014-10-03

KS C IEC 62255-5-1:2014 宽带数字通信（高比特率数字接入电信网络）用多芯和对称对/四芯电缆室外电缆第 5-1 部分：填充引入电缆空白详细规范

이 개별 규격은 광대역 디지털 통신용 다중코어 대칭형 페어/쿼드 충전 케이블을 기술하는 개별 규격의 레이아웃과 양식을 규정한다. 개별 규격은 개별 규격에 기초하여 국가 기관, 제조업체 또는 사용자가 작성할 수도 있다.?

Multicore and symmetrical pair/quad cables for broadband digital communications(high bit rate digital access telecommunication networks) — Outside plant cables — Part 5-1: Filled drop cables — Blank detail specification

ICS: 33.120.20
CCS
发布: 2014-10-03
实施: 2014-10-03

KS C IEC 62255-5-1-2014(2019) 用于宽带数字通信（高比特率数字接入电信网络）的多芯和对称双绞线/四线电缆 - 外部电缆 - 第5-1部分:填充电缆 - 空白详细规范

ICS: 33.120.20
CCS
发布: 2014-10-03
实施

KS C IEC 61156-5-1:2014 数字通信用多芯和对称双绞线/绞合电缆第 5-1 部分：传输特性高达 1 000 MHz 的对称绞合线/绞合电缆”水平地面布线“空白详细规范”

KS C IEC 61156의 이 부는 KS X ISO/IEC 11801과 ISO/IEC 24702의 정의에 따른 등급 D, E, EA, F, FA 채널 (Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A)에서 수평 바닥 케이블링을 위한 대칭형 페어/쿼드 케이블에 대해 기술한다.이 개별 규격은 산업 환경에 대한 케이블링을 규정한 환경 분류로부터 비롯한 추가적인 권장 환경 특성과 가혹도를 포함한다.개별 규격은 디지털 통신용으로 1 000 MHz까지의 전송특성을 갖는 대칭형 페어/쿼드 케이블을 설명하는 세부 표준에 대한 배치 및 스타일을 결정한다. 개별 규격에 근거한 세부 표준은 국가기관이나 제조자 또는 사용자가 작성할 수 있다.?

Multicore and symmetrical pair/quad cables for digital communications — Part 5-1: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz — Horizontal floor wiring — Blank detail specification

ICS: 33.120.20
CCS
发布: 2014-10-03
实施: 2014-10-03

KS C IEC 62255-3-1:2014 宽带数字通信用多芯和对称对/四芯电缆（高比特率数字接入电信通信（高比特率数字接入电信空白详细规范

Multicore and symmetrical pair/quad cables for broadband digital communications(high bit rate digital access telecommunication communications(high bit rate digital access telecommunication Blank detail specification

ICS: 33.120.20
CCS
发布: 2014-10-03
实施: 2014-10-03

KS C IEC 61156-6:2014 数字通信用多芯和对称对/四芯电缆第6部分：传输特性高达 1 000 MHz 的对称对/四芯电缆'工作区布线'规范

KS C IEC 61156의 이 부는 IEC 61156-1과 관련이 있다. 여기에 기술한 케이블은 KS X ISO/IEC 1801의 정의에 따른 공사 현장 배선을 위한 것이다.케이블은 개별 차폐, 공동 차폐 및 비차폐의 페어 또는 쿼드를 포함한다. 전송 특성과 케이블의 주파수 범위(표 1 참조)는 20 ℃에서 규정한다.?이 케이블은 동시에 4 페어를 사용하는 다양한 통신 채널에 사용할 수 있다. 이런 관점에서 이 품종 격은 시스템 개발자들이 새로운 시스템을 평가하는데 필요한 케이블 특성을 제공한다.이 표준에서 다루는 케이블은 통신 시스템에서 통상적으로 적용하는 전압과 전류로 운전하는 것을 적으로 한다. 이 케이블은 공공 시설 간선의 전력 공급장치와 같은 저 임피던스 전원과 결합하여사용하지 않는다.?

Multicore and symmetrical pair/quad cables for digital communications — Part 6: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz — Work area wiring — Sectional specification

ICS: 33.120.20
CCS
发布: 2014-10-03
实施: 2014-10-03

KS C IEC 62255-2-1:2014 宽带数字通信（高比特率数字接入电信网络）用多芯和对称对/绞电缆室外电缆第 2-1 部分：未填充电缆空白详细规范

이 개별 규격은 광대역 디지털 통신용 다중코어 대칭형 페어/쿼드 비충전 케이블을 기술하는 개별 규격의 레이아웃과 양식을 규정한다. 개별 표준은 개별 규격에 기초하여 국가 기관, 제조업체 또는 사용자가 작성할 수도 있다.?

Multicore and symmetrical pair/quad cables for broadband digital communications(high bit rate digital access telecommunication networks) — Outside plant cables — Part 2-1: Unfilled cables — Blank detail specification

ICS: 33.120.20
CCS
发布: 2014-10-03
实施: 2014-10-03

KS C IEC 61156-5-1-2014(2019) 用于数字通信的多芯和对称双绞线/四线电缆 - 第5-1部分:传输特性高达1 000 MHz的对称/四线电缆 - 水平地板接线 - 空白详细规范

ICS: 33.120.20
CCS
发布: 2014-10-03
实施

KS C IEC 61156-6-2014(2019) 数字通信用多芯对称对/四芯电缆.第6部分:传输特性小于1000MHz的对称对/四芯电缆.工作区布线.分规范

ICS: 33.120.20
CCS
发布: 2014-10-03
实施

KS C IEC 61935-3-2014(2019) 平衡和同轴信息技术布线的测试 - 第3部分:ISO/IEC 15018和相关标准中规定的安装电缆