共找到 72 条与 电信专用测量设备 相关的标准,共 5 页
IEC 62129-1:2016 specifies procedures for calibrating an optical spectrum analyzer that is developed for use in fibre-optic communications and designed to measure the power distribution of an optical spectrum. It does not apply to an optical wavelength meter that measures only centre wavelengths, a Fabry-Perot interferometer or a monochromator that has no display unit. This first edition of IEC 62129-1 cancels and replaces the first edition of IEC 62129, published in 2006. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - update of term and definitions; - update of calibration conditions; - calculation change of uncertainties related to wavelength temperature dependence, power linearity, power level temperature dependence; - move of Annex E to the bibliography. Keywords: calibrating an optical spectrum analyser
Calibration of wavelength/optical frequency measurement instruments - Part 1: Optical spectrum analyzers
This international standard is applicable to instruments measuring radiant power emitted from sources which are typical for the fibre-optic communications industry. These sources include laser diodes, light emitting diodes (LEDs) and fibre-type sources. The radiation may be divergent or collimated. The standard describes the calibration of power meters to be performed by calibration laboratories or by power meter manufacturers.
Calibration of fibre-optic power meters
Methods of measurement for the power consumption of audio, video and related equipment
Methods of measurement for the power consumption of audio, video and related equipment (IEC 62087:2011); German version EN 62087:2012
Realtime audiovisual information system (RAVIS). Norms and methods of measurement assurance
Methods of measurement for the power consumption of audio, video and related equipment
Methods of measurement for the power consumption of audio, video and related equipment (IEC 62087:2008); German version EN 62087:2009
Automatic receiver equipment for spectrum monitoring stations. Technical requirements and test methods
This International Standard specifies methods of measurement for the power consumption of television sets, video recording equipment, Set Top Boxes (STBs), audio equipment and multi-function equipment for consumer use. Television sets include, but are not limited to, those with CRT, LCD, PDP or projection technologies. Moreover the different modes of operation which are relevant for measuring power consumption are defined. The methods of measurement are only applicable for equipment which can be connected to the mains. The measuring conditions in this standard represent the normal use of the equipment and may differ from specific conditions, for example as specified in safety standards.
Methods of measurement for the power consumption of audio, video and related equipment
This standard provides the techniques and rationale for referencing acoustic telephony measurements to the free field. It applies to ear related measurements such as receive, sidetone and overall.
Standard for the Application of Free Field Acoustic Reference to Telephony Measurements
The purpose of this document is to provide a test method for measuring return loss of 'F' Male Connectors with Cable in the frequency range of 5 MHz to 1002 MHz by utilizing the time domain-gating feature of the network analyzer. Male 'F' connectors that conform to SCTE 123 2006; Specification for 'F' Connector, Male, Feed-Through or SCTE 124 2006; Specification for 'F' Connector, Male, Pin Type that are used with 75 ohm flexible RF coaxial cable, such as, but not limited to, ANSI/ SCTE 74; Specification for Braided 75 ohm Flexible RF Coaxial Drop Cable shall be utilized.
Test Method for “F” Connector Return Loss
The purpose of this document is to establish the standard methodology to measure an amplifier's distortion caused by an upstream signal leaking through the diplex filter that is built inside of the amplifier of a Cable Telecommunications System.
Test Method for Distortion of 2-way Amplifiers Caused by Insufficient Isolation of Built in Diplex Filter
本规范规定了电子产品制造与应用系统防静电的测试方法。 本规范适用于电子产品制造与应用系统防静电的检测,如:接地系统、地面(地垫)、墙体、工作台、台垫、工作椅、工位器具、物流传递器具、包装用品、人体静电防护用品、操作维修工具、离子静电消除器等。
General specification of testing method for electrostatic protection electronic production manufacturing and using system
Automatic equipment for spectrum monitoring stations. Technical requirements and test methods
Jitter and wander measuring equipment for digital systems which are based on the synchronous digital hierarchy (SDH); Erratum 1
Methods of measurement for the power consumption of audio, video and related equipment.
Methods of measurement for the power consumption of audio, video and related equipment
Erratum to Recommendation ITU-T O.81/Appendix I (06/98)
MIL-HDBK-173A, dated 23 September 1986, has been reviewed and determined to be valid for use in acquistion.
AUDIO EQUIPMENT
In the following Appendix I a brief description of a test signal is given, stating its particular advantages for measurement of amplitude and phase simultaneously. It was formerly published as Supplement 3.7 in the Blue Book (1988), Fascicle IV.4, and then renumbered on 26 June 1998 as Appendix I to ITU-T O.81 without further modification.
A measuring signal (multitone test signal) for fast measurement of amplitude and phase for telephone type circuits
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号