33.180.20 纤维光学和光学互连器件 标准查询与下载

GSO IEC 61300-3-50:2017 光纤互连装置和无源元件 基本测试和测量程序 第3-50部分：检查和测量 光空间开关的串扰

This part of IEC 61300 describes the procedure to measure the crosstalk of optical signals between the ports of a multiport M x N (M input ports and N output ports) fibre optic spatial switch. The crosstalk is defined as the ratio of the optical power at an output port which comes from the unconnected input port, to the optical power at the output port which comes from the connected input port.

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-50: Examinations and measurements - Crosstalk for optical spatial switches

GSO IEC 61300-3-52:2017 光纤互连装置和无源元件 基本测试和测量程序 第3-52部分：检查和测量 导孔和对准销变形常数 8 度角 PC 矩形插芯的 CD 单模 f

This part of IEC 61300 describes a procedure to measure guide hole and alignment pin deformation constant, CD for 8 degree angled PC rectangular ferrule multi-fibre connectors.

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-52: Examinations and measurements - Guide hole and alignment pin deformation constant, CD for 8 degree angled PC rectangular ferrule, single mode f

GSO IEC 61300-3-49:2017 光纤互连装置和无源元件 基本测试和测量程序 第3-49部分：检查和测量 矩形插芯多光纤连接器的导销保持力

The purpose of this part of IEC 61300 is to describe the procedure required to measure the guide pin retention force for rectangular ferrule multi-fibre connectors in order to ensure that the pins remain in place during mating/unmating.

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-49: Examinations and measurements - Guide pin retention force for rectangular ferrule multi-fibre connectors

GSO IEC 61753-088-2:2017 光纤互连设备和无源元件 性能标准 第088-2部分：C 类通道间隔为 800 GHz 的非连接器单模光纤 LAN WDM 设备 受控环境

This part of IEC 61753 contains the minimum initial test and measurement requirements and severities which a non-connectorized single-mode fibre optic Local Area Network Wavelength Division Multiplexing (LAN WDM) device with channel spacing of 800 GHz needs to satisfy in order to be categorized as meeting the requirements of Category C – Controlled environments, as defined in Annex A of IEC 61753-1:2007. The applications of LAN WDM devices are optical MUX and DEMUX for 100GBASE-LR4 (required operating range of 2 m to 10 km) and 100GBASE-ER4 (required operating range of 2 m to 30 km) defined in IEEE P802.3ba, as shown in Annex D. The requirements cover both an integrated 1 × 4 LAN WDM device and an individual 1 × 2 LAN WDM device for cascaded module construction.

Fibre optic interconnecting devices and passive components - Performance standard - Part 088-2: Non-connectorized single-mode fibre optic LAN WDM devices with channel spacing of 800 GHz for category C - Controlled environments

GSO IEC 61754-20-100:2017 光纤互连装置和无源元件 光纤连接器接口 第20-100部分：具有与 IEC 61076-3-106 相关的保护外壳的 LC 连接器的接口标准

This part of IEC 61754 covers connectors with protective housings. The housing is defined as variant 4 in IEC 61076-3-106:2006. These connectors use a push-pull coupling mechanism. To connect the fibres inside the housing the LC interface is used as described in IEC 61754-20:2002. The fully assembled variants (connectors) described in this document incorporate fixed and free connectors.

Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 20-100: Interface standard for LC connectors with protective housings related to IEC 61076-3-106

GSO IEC 61300-3-53:2017 光纤互连装置和无源元件 基本测试和测量程序 第3-53部分：检查和测量 基于阶跃折射率多模二维远场数据的环形角通量 (EAF) 测量方法

This part of IEC 61300 is intended to characterize the encircled angular flux of measurement step index multimode waveguide light sources, in which most of the transverse modes are excited. The term waveguide is understood to include both channel waveguides and optical fibres but not slab waveguides in this standard. Encircled angular flux (EAF) is the fraction of the total optical power radiating from a step index multimode waveguide’s core within a certain solid angle. The EAF is measured as a function of the numerical aperture full angle. The basic approach is to collect, for every measurement, two dimensional far field data using a calibrated camera and to convert them mathematically into encircled angular flux.

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-53: Examinations and measurements - Encircled angular flux (EAF) measurement method based on two-dimensional far field data from step index multimo

GSO IEC 61754-30:2017 光纤互连装置和无源元件 光纤连接器接口 第30部分：CLIK型连接器系列

This part of IEC 61754 defines the standard interface dimensions for the type CLIK series of connectors.

Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 30: Type CLIK connector series

GSO IEC 62149-9:2017 光纤有源元件和设备 性能标准 第9部分：种子反射半导体光放大器收发器

This part of IEC 62149 covers the performance specification for seeded reflective semiconductor optical amplifier (RSOA) transceivers used for the fibre optic telecommunication and optical data transmission applications. The performance standard contains a definition of the product performance requirements together with a series of sets of tests and measurements with clearly defined conditions, severities, and pass/fail criteria. The tests are intended to be run on a “once-off” basis to prove any product’s ability to satisfy the performance standard’s requirements. A product that has been shown to meet all the requirements of a performance standard can be declared as complying with the performance standard, but should then be controlled by a quality assurance/quality conformance program.

Fibre optic active components and devices - Performance standards - Part 9: Seeded reflective semiconductor optical amplifier transceivers

GSO IEC 61300-2-7:2017 光纤互连装置和无源元件 基本测试和测量程序 第2-7部分：测试 弯矩

This part of IEC 61300 details a procedure for determining the suitability of a fibre optic device to withstand the environmental condition of a bending moment which may occur in actual use, storage and/or transport. The test is primarily intended to permit the observation of effects of a bending moment. The bending moment may result in effects that would destroy functional utility, cause loss of physical strength, and cause changes in other important mechanical properties. Degradation of optical properties may also occur. The specimen may be a component, a connector set, a splice or other device combination intended for fibre optic usage.

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-7: Tests - Bending moment

GSO IEC 61754-7-1:2017 光纤互连器件和无源元件 光纤连接器接口 第7-1部分：MPO 型连接器系列 一根光纤

This part of IEC 61754 defines the standard interface dimensions for type MPO family of connectors with one row of fibres.

Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 7-1: Type MPO connector family - One fibre row

GSO IEC 61300-2-10:2017 光纤互连装置和无源元件 基本测试和测量程序 第2-10部分：测试 抗挤压性

This part of IEC 61300 evaluates the effect of loads which might occur when fibre optic devices are exposed to critical situations such as being stepped on or being run over by vehicle tyres.

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-10: Tests - Crush resistance

GSO IEC 61753-031-2:2017 光纤互连设备和无源元件 性能标准 第031-2部分：C 类非连接器单模 1×N 和 2×N 非波长选择分支设备 受控环境

This part of IEC 61753 contains the minimum initial tests and measurement requirements and severities which a non-wavelength selective branching device (NWBD) should satisfy in order to be categorized as meeting the requirement of this IEC standard. The requirements cover balanced bidirectional non-connectorized single-mode 1 × N and 2 × N non wavelength-selective branching devices for use in an IEC Category C environment (N is the number of branching ports), especially but not exclusively used for PON application. For balanced NWBD two attenuation and uniformity performance classes are considered: class A (premium class) which meets more restrictive requirements (i.e. for extended reach PON application) and class B (standard class) for standard application (i.e. normal reach PON application). The requirements also cover unbalanced bidirectional non-connectorized single-mode, nonwavelength-selective branching devices; however, the specifications of unbalanced branching devices are limited to 1 × 2 and 2 × 2 devices because they are the most commonly used.

Fibre optic interconnecting devices and passive components - Performance standard - Part 031-2: Non-connectorized single-mode 1×N and 2×N non-wavelength-selective branching devices for Category C - Controlled environment

GSO IEC 61753-084-2:2017 光纤互连设备和无源元件性能标准 第084-2部分：C 类非连接器单模 980/1550 nm WWDM 设备 受控环境

This part of IEC 61753 contains the minimum initial test and measurement requirements and severities which a fibre optic pigtailed 980/1 550 nm WWDM device must satisfy in order to be categorized as meeting the requirements of category C (controlled environments), as defined in Annex A of IEC 61753-1. The requirements cover devices with single-mode non-connectorised pigtails. This device has three ports; 980 nm input, 1 550 nm input and common port for output of combining 980/1 550 nm input light.

Fibre optic interconnecting devices and passive components performance standard - Part 084-2: Non connectorised single-mode 980/1550 nm WWDM devices for category C - Controlled environment

GSO IEC 61753-021-3:2017 光纤互连装置和无源元件 性能标准 第021-3部分：U 类单模光纤连接器 非受控环境

This part of IEC 61753 defines minimum initial test and measurement requirements and severities which a single-mode connector, either part of a pigtail, or part of a cord, must satisfy in order to be categorized as meeting the IEC standard category U (uncontrolled environment).

Fibre optic interconnecting devices and passive components - Performance standard - Part 021-3: Single-mode fibre optic connectors for category U - Uncontrolled environment

GSO IEC 61300-2-35:2017 光纤互连装置和无源元件 基本测试和测量程序 第2-35部分：测试 电缆章动

This part of IEC 61300 details procedures for determining the suitability of a fibre optic device to withstand nutation that may occur during operation, service, storage and/or transport. The test is intended to indicate the performance of such devices when exposed to torsion and bending as a combined load.

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-35: Tests - Cable nutation

GSO IEC 61300-2-6:2017 光纤互连装置和无源元件 基本测试和测量程序 第2-6部分：测试 耦合机构的拉伸强度

This part of IEC 61300 describes a test to ensure that the coupling mechanism of a connector set or connector and device combination will withstand the axial loads likely to be applied during normal service.

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-6: Tests - Tensile strength of coupling mechanism

GSO IEC 62148-18:2017 光纤有源组件和设备 封装和接口标准 第18部分：与 LC 连接器接口一起使用的 40 Gbit/s 串行发送器和接收器组件

This part of IEC 62148 covers the 40-Gbit/s serial physical interface specification of transmitter and receiver components for use with the LC connector interface. The purpose of this standard is to adequately specify the physical requirements of optical transmitters and receivers that will enable mechanical interchangeability of transmitters and receivers complying with this standard both at the PCB level and for any panel-mounting requirement.

Fiber optic active components and devices - Package and interface standards - Part 18: 40-Gbit/s serial transmitter and receiver components for use with the LC connector interface

GSO IEC 61753-143-2:2017 光纤互连装置和无源元件 性能标准 第143-2部分：C 类单模光纤传输的光无源基于 VIPA 的色散补偿器 受控环境

This part of IEC 61753 contains the minimum test and measurement requirements and severity levels that a passive chromatic dispersion compensator (PCDC) using virtually imaged phased array (VIPA) must satisfy in order to be categorized as meeting the IEC standard, category C-controlled environments. Generally, PCDCs are used to reduce the magnitude of chromatic dispersion (CD) between regenerators by adding CD to the span that has a sign opposite to the total CD of the fibre cable and components. The requirements cover non-connectorized PCDCs used in single-channel transmission and wavelength division multiplexing (WDM) transmission in single-mode fibres (IEC 60793-2-50 B1/B2/B4).

Fibre optic interconnecting devices and passive components - Performance standard - Part 143-2: Optical passive VIPA-based dispersion compensator of single-mode fibre transmission for category C - Controlled environment

GSO IEC 61300-3-47:2017 光纤互连装置和无源元件 基本测试和测量程序 第3-47部分：检查和测量 使用干涉测量法的 PC/APC 球形抛光插芯的端面几何形状

This part of IEC 61300 describes a procedure to measure the end face geometry of a spherically polished ferrule or connector. Within this standard the words “ferrule” and “connector” can be used interchangeably.

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-47: Examinations and measurements - End face geometry of PC/APC spherically polished ferrules using interferometry

GSO IEC 61300-3-48:2017 光纤互连装置和无源元件 基本测试和测量程序 第3-48部分：检查和测量 矩形插芯多光纤连接器耦合套管的弹簧压缩力

The purpose of this part of IEC 61300 is to describe the procedure required to measure the spring compression force of the coupling sleeve for rectangular ferrule multi-fibre connectors.

Fibre optic interconnect devices and passive components - Basic test and measurement procedures - Part 3-48: Examinations and measurements - Spring compression force of the coupling sleeve for rectangular ferrule multi-fibre connectors