33.180.20 纤维光学和光学互连器件 标准查询与下载
共找到 3544 条与 纤维光学和光学互连器件 相关的标准，共 237 页
This part of IEC 61300 details procedures for determining the suitability of a fibre optic device to withstand nutation that may occur during operation, service, storage and/or transport. The test is intended to indicate the performance of such devices when exposed to torsion and bending as a combined load.
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-35: Tests - Cable nutation
- ICS
- 33.180.20
- CCS
- 发布
- 2017-10-03
- 实施
This part of IEC 61753 contains the minimum initial performance, test and measurement requirements and severities which a fibre optic pigtailed wide wavelength division multiplexing (WWDM) device for monitoring passive optical networks (PON) using an optical time-domain reflectometer (OTDR) satisfies in order to be categorized as meeting the requirements of category C (controlled environments), as defined in Annex A of IEC 61753-1:2007. Annex B of this standard provides information concerning the principle and function of the OTDR monitoring WWDM.
Fibre optic interconnecting devices and passive components - Performance standard - Part 089-2: Non-connectorized single-mode bidirectional OTDR monitoring WWDM devices for category C - Controlled environment
- ICS
- 33.180.20
- CCS
- 发布
- 2017-10-03
- 实施
This part of IEC 61754 defines the standard interface dimensions for the type LF3 family of connectors.
Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 28: Type LF3 connector family
- ICS
- 33.180.20
- CCS
- 发布
- 2017-10-03
- 实施
This part of IEC 61300 describes a procedure to measure the end face geometry of a spherically polished ferrule or connector. Within this standard the words “ferrule” and “connector” can be used interchangeably.
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-47: Examinations and measurements - End face geometry of PC/APC spherically polished ferrules using interferometry
- ICS
- 33.180.20
- CCS
- 发布
- 2017-10-03
- 实施
This part of IEC 61753 contains the minimum initial test and measurement requirements and severities which non-connectorized single-mode fibre electrically controlled variable optical attenuator needs to satisfy in order to be categorised as meeting the requirements of category C-Controlled environments, as defined in Annex A of IEC 61753-1:2007.
Fibre optic interconnecting devices and passive components - Performance standard - Part 053-2: Non-connectorized single-mode fibre, electrically controlled, variable optical attenuator for category C - Controlled environments
- ICS
- 33.180.20
- CCS
- 发布
- 2017-10-03
- 实施
This part of IEC 61755 defines a set of prescribed conditions that should be maintained in order to satisfy the requirements of non-angled polished reference connections. The prescribed conditions include dimensional limits and optical fibre requirements of the optical interface to meet specific requirements for reference connection (plugs and adaptors) used for attenuation measurements. Two different grades for reference connections are defined in this standard. The use of each of these grades depends on the application and on the targeted attenuation measurement uncertainty. The model uses a Gaussian distribution of light intensity over the specified restricted mode field diameter (MFD) range. This standard is intended to be used for shipping and acceptance inspections. The reference connector plug is specified for B1.1, B1.3 and B6 fibres as specified in IEC 60793-2-50. The use of the reference connector plug would not be recommended where classification of fibre is difficult, for example construction and maintenance of cable plant.
Fibre optic interconnecting devices and passive components - Connector optical interfaces - Part 2-4: Connection parameters of non-dispersion shifted single-mode physically contacting fibres - Non-angled for reference connection applications
- ICS
- 33.180.20
- CCS
- 发布
- 2017-10-03
- 实施
This part of IEC 61753 contains the minimum initial test and measurement requirements and severities which a fibre optical fuse satisfies in order for it to be categorised as meeting the requirements of single mode fibre pigtailed style optical fuse used in controlled environments. Optical performance specified in this document relates to in-line type configurations fuses only.
Fibre optic interconnecting devices and passive components - Performance standard - Part 056-2: Single mode fibre pigtailed style optical fuse for category C - Controlled environment
- ICS
- 33.180.20
- CCS
- 发布
- 2017-10-03
- 实施
This part of IEC 62148 covers the 40-Gbit/s serial physical interface specification of transmitter and receiver components for use with the LC connector interface. The purpose of this standard is to adequately specify the physical requirements of optical transmitters and receivers that will enable mechanical interchangeability of transmitters and receivers complying with this standard both at the PCB level and for any panel-mounting requirement.
Fiber optic active components and devices - Package and interface standards - Part 18: 40-Gbit/s serial transmitter and receiver components for use with the LC connector interface
- ICS
- 33.180.20
- CCS
- 发布
- 2017-10-03
- 实施
The purpose of this part of IEC 61300 is to ensure that the captivation or the attachment of the cable to the fibre optic devices such as fibre optic closures will withstand compressive axial loads likely to be applied during normal service.
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-11: Tests - Axial compression
- ICS
- 33.180.20
- CCS
- 发布
- 2017-10-03
- 实施
This part of IEC 61753 contains the minimum initial test and measurement requirements and severities which an optical power limiter needs to satisfy in order to be categorized as meeting the requirements of single mode fibre pigtailed style optical power limiter used in controlled environments. Optical performance specified in this standard relates to in-line type configuration power limiters only.
Fibre optic interconnecting devices and passive components - Performance standard - Part 058-2: Single mode fibre pigtailed style optical power limiter for category C - Controlled environment
- ICS
- 33.180.20
- CCS
- 发布
- 2017-10-03
- 实施
This part of IEC 61300 is intended to characterize the encircled angular flux of measurement step index multimode waveguide light sources, in which most of the transverse modes are excited. The term waveguide is understood to include both channel waveguides and optical fibres but not slab waveguides in this standard. Encircled angular flux (EAF) is the fraction of the total optical power radiating from a step index multimode waveguide’s core within a certain solid angle. The EAF is measured as a function of the numerical aperture full angle. The basic approach is to collect, for every measurement, two dimensional far field data using a calibrated camera and to convert them mathematically into encircled angular flux.
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-53: Examinations and measurements - Encircled angular flux (EAF) measurement method based on two-dimensional far field data from step index multimo
- ICS
- 33.180.20
- CCS
- 发布
- 2017-10-03
- 实施
IEC 62150-5:2017 specifies test and measurement procedures for the wavelength channel tuning time of tuneable transmitters. It applies to laser transmitters, and to the transmitter portion of transceivers. This procedure examines whether the device or module satisfies the appropriate performance specification. The method described in this document uses optical filters to transfer the transition of the output wavelength to the transition of the optical power. This is because the transient response of the output wavelength before stabilization at steady-state of the target wavelength channel is too fast to measure using a wavelength meter or an optical spectrum analyser. Reference optical filter sets are described in Annex A. Keywords: test and measurement procedures of the wavelength channel tuning time
Fibre optic active components and devices - Test and measurement procedures - Part 5: Wavelength channel tuning time of tuneable transmitters
- ICS
- 33.180.20
- CCS
- 发布
- 2017-08-18
- 实施
- 2017-09-15 (7)
1.1 This specification covers the requirements for fiberoptic position switches (proximity and limit). This specification does not include switches that transfer an optical signal from one path to another by an external force or energy applied to the switch. 1.2 Special requirements for naval shipboard applications are included in the Supplement. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. Where information is to be specified, it shall be stated in SI units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for Switch, Position Proximity (Noncontact) or Limit (Mechanical Contact), Fiber-Optic
- ICS
- 33.180.20
- CCS
- 发布
- 2017-08-01
- 实施
Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Tests. Strength of mounted adaptor
- ICS
- 33.180.20
- CCS
- M33
- 发布
- 2017-07-10
- 实施
- 2017-07-10
Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 32: Type DiaLink connector family (IEC 61754-32:2016); German version EN 61754-32:2016
- ICS
- 33.180.20
- CCS
- 发布
- 2017-07
- 实施
Fibre optic interconnecting devices and passive components - Performance standard - Part 052-6: Single-mode fibre non-connectorized fixed attenuator - Category O in outside plant environment (IEC 61753-052-6:2016); German version EN 61753-052-6:2016
- ICS
- 33.180.20
- CCS
- 发布
- 2017-07
- 实施
Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 34: Type URM connector family (IEC 61754-34:2016); German version EN 61754-34:2016
- ICS
- 33.180.20
- CCS
- 发布
- 2017-07
- 实施
Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 31: Type N-FO connector family (IEC 61754-31:2016); German version EN 61754-31:2016
- ICS
- 33.180.20
- CCS
- 发布
- 2017-07
- 实施
Dynamic modules - Part 3-1: Performance specification templates - Dynamic channel equalizers (IEC 62343-3-1:2016); German version EN 62343-3-1:2016
- ICS
- 33.180.20
- CCS
- 发布
- 2017-07
- 实施
Fibre optic interconnecting devices and passive components - Performance standard - Part 052-3: Single-mode fibre non-connectorized fixed attenuator - Category U in uncontrolled environment (IEC 61753-052-3:2016); German version EN 61753-052-3:2016
- ICS
- 33.180.20
- CCS
- 发布
- 2017-07
- 实施
