33.180.20 纤维光学和光学互连器件 标准查询与下载

EN 61300-2-55:2017 光纤互连设备和无源元件 基本测试和测量程序 第 2-55 部分：测试 安装适配器的强度

IEC 61300-2-55: 2017 describes the test procedure to measure the mounting strength of an optical adaptor or receptacle to a fixture. Keywords: mounting strength of an optical adaptor

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-55: Tests - Strength of mounted adaptor

DIN EN 61300-2-47:2017 光纤互连器件和无源部件.基本试验和测量规程.第2-47部分:试验.热冲击(IEC 61300-2-47-2016);德文版本EN 61300-2-47-2016

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-47: Tests - Thermal shocks (IEC 61300-2-47:2016); German version EN 61300-2-47:2016

IEC 61753-121-2:2017 纤维光学互连器件和无源元件.性能标准.第121-2部分:C类用单模纤维和圆柱形套圈连接器的单工和双工软线.受控环境

This part of IEC 61753 specifies the test requirements for cords including reference cords used in a controlled (Category C) environment according to IEC 61753-1@ where the connectors already comply with the Category C requirements of IEC 61753-1. The tests selected are a subset of the connector tests from IEC 61753-1 appropriate for requalification with additional requirements relevant to cords and the connector/cable interface. The cords consist of simplex or duplex fibre optic cable terminated at each end of the cable with single-mode fibre optic connector plugs with cylindrical ferrules. The operational wavelength range is between 1 260 nm and 1 625 nm. Short length cords are used as test samples as the attenuation of the cord and the temperature cycling performance will be affected by longer lengths of cable. It is important that any qualification of a cord whose length is greater than 5 m takes these factors into account. The relevant requirements for the mechanical interface of connector sets are covered by the IEC 61754 all parts. The relevant requirements for the optical interface of connector sets are covered by IEC 61755 (all parts). The relevant requirements for performance of connector sets are covered by IEC 61753 (all parts). The relevant requirements for fibres are covered by IEC 60793-2-50. The relevant requirements for cables for cords are covered by IEC 60794-2- 50.

Fibre optic interconnecting devices and passive components - Performance standard - Part 121-2: Simplex and duplex cords with single-mode fibre and cylindrical ferrule connectors for category C - Cont

IEC 62150-5:2017 光纤有源器件和器件 - 测试和测量程序第5部分:可调谐变送器的波长通道调谐时间

Fibre optic active components and devices - Test and measurement procedures - Part 5: Wavelength channel tuning time of tuneable transmitters

DIN EN 61300-3-25:2017 光纤互连器件和无源元件.基本试验和测量程序.第3-25部分:检查和测量.套管和装有光纤套管的同心度(IEC 61300-3-25-2016);德文版本EN 61300-3-25-2016

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-25: Examinations and measurements - Concentricity of non-angled ferrules and non-angled ferrules with fibre installed (IEC 61300-3-25:2016); German

BS EN 61202-1:2017 光纤互连器件和无源元件.光纤隔离器.总规范

Fibre optic interconnecting devices and passive components. Fibre optic isolators. Generic specification

BS EN 61300-2-9:2017 光纤互联装置和无源部件.基本试验和测试规程.试验.冲击

Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Tests. Shock

BS EN 61755-3-10:2017 光纤互连器件和无源元件. 连接器光学接口. 非色散位移式单相物理连接纤维的连接参数. 非角度, 无套圈, 孔对齐连接器

Fibre optic interconnecting devices and passive components. Connector optical interfaces. Connector parameters of non-dispersion shifted single mode physically contacting fibres. Non-angled, ferrule-less, bore alignment connectors

YD/T 3249-2017 无线射频拉远单元用光纤活动连接器

本标准规定了无线射频拉远单元用光纤活动连接器(以下简称拉远光纤连接器)的术语和定义、分类、要求、测量和试验、质量评定程序、检验规则、标志、包装、运输和贮存。 本标准适用于双芯及四芯无线射频拉远单元用光纤活动连接器。

Optical fiber connector for wireless remote radio unit

EN 61202-1:2017 光纤互连器件和无源器件.光纤绝缘体.第1部分:通用规范

IEC 61202-1: 2016(E) applies to isolators used in the field of fibre optics, all exhibiting the following features: - they are non-reciprocal optical devices, in which each port is either an optical fibre or fibre optic connector; - they are passive devi c es containing no opto-electronic or other transducing elements; - they have two optical ports for directionally transmitting optical power. This fourth edition cancels and replaces the third edition published in 2009. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - the terms and definitions were reconsidered; - quality assessment level was deleted from classification; - the clause numbers of Annexes A and B have been rearranged. Keywords: isolators used in the field of fibre optics

Fibre optic interconnecting devices and passive components - Fibre optic isolators - Part 1: Generic specification

EN 61755-3-10:2017 光纤互连设备和无源元件 连接器光学接口 第 3-10 部分：非色散位移单模物理接触光纤的连接器参数 无角度、无套圈、孔对准连接器

IEC 61755-3-10: 2016 defines certain dimensional limits of a 125 mm diameter single mode silica fibre optical interface and an alignment bore to meet specific requirements for non-angled fibre-to-fibre interconnection as defined in IEC 61755-2-1. The silica fibre materials specified in this document are suitable for use in categories C, U, E and O as defined in IEC 61753-1. Keywords: 125 mm diameter single mode silica fibre optical interface

Fibre optic interconnecting devices and passive components - Connector optical interfaces - Part 3-10: Connector parameters of non-dispersion shifted single mode physically contacting fibres - Non-angled, ferrule-less, bore alignment connectors

EN 61300-2-9:2017 光纤互连器件和无源元件.基本试验和测量程.第2-9部分:试验:冲击

IEC 61300-2-9: 2017(E) defines a test method to reveal mechanical weakness and/or degradation of fibre optic devices when subjected to repetitive or non-repetitive mechanical shocks. It simulates infrequent repetitive or non-repetitive shocks likely to be encountered in normal service or during transportation. This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - inserted clause "Terms and definitions"; - added precise descriptions to clause "Apparatus"; - added sub clause "Testing" into clause "Procedure"; - added "Bibliography". Keywords: degradation of fibre optic devices, vibration test, transport test

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-9: Tests - Shock

JIS C 61300-3-4:2017 光纤连接器和无源组件.基础测试和测量规程.第3-4部分:衰减

Fiber optic interconnecting devices and passive components -- Basic test and measurement procedures -- Part 3-4: Attenuation

JIS C 5914-3:2017 光学环行器. 第3部分: 非连接式单模光纤环行器

Optical circulators -- Part 3: Non-connectorized single-mode fiber optic circulators

JIS C 5920-3:2017 光纤无源功率控制器件. 第3部分: 非连接器化单模光纤电控可变光衰减器

Fiber optic passive power control devices -- Part 3: Non-connectorized, single-mode fiber, electrically controlled, variable optical attenuator

JIS C 5953-7:2017 光纤有源元件和器件 性能标准 第7部分：GPON 收发器

Fiber optic active components and devices -- Performance standards -- Part 7: GPON transceivers

JIS C 5954-4:2017 光纤有源元件和器件. 试验和测量程序. 第4部分: GPON收发器

Fiber optic active components and devices -- Test and measurement procedures -- Part 4: GPON transceivers

IEC 61300-2-55:2017 光纤互连设备和无源元件 基本测试和测量程序 第 2-55 部分：测试 安装适配器的强度

This part of IEC 61300 describes the test procedure to measure the mounting strength of an optical adaptor or receptacle to a fixture.

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-55: Tests - Strength of mounted adaptor

BS PD IEC/TR 62343-6-6:2017 动态模块.设计指南.动态模块的光学单元用故障模式效应分析

Dynamic modules. Design guide. Failure mode effect analysis for optical units of dynamic modules

DIN EN 61300-2-37:2017 纤维光学互连器件和无源元件.基本试验和测量程序.第2-37部分:试验.纤维光学外壳的光缆弯曲(IEC 61300-2-37-2016);德文版本EN 61300-2-37-2016

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-37: Tests - Cable bending for fibre optic closures (IEC 61300-2-37:2016); German version EN 61300-2-37:2016