43.040.10 电气和电子设备 标准查询与下载

T/STIC 110082-2022 多功能超声波燃气表

本文件规定了多功能超声波燃气表（以下简称燃气表）的技术要求、试验方法、检验规则、标志、包装、运输、贮存。 本文件适用于最大工作压力不超过50kPa、最大流量不超过160m3/h、准确度等级为1.5级的燃气表。

Multifunctional ultrasonic gas meter

DB43/T 2538-2022 智能网联公交车路云一体化系统技术规范 第1部分：总体技术要求

Technical Specifications for Intelligent Connected Bus Road-Cloud Integrated System Part 1: General Technical Requirements

T/ZZB 2921-2022 摩托车发动机系统用加热型片式氧传感器

本文件规定了摩托车发动机系统用加热型片式氧传感器的术语和定义、结构型式、工作条件、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本文件适用于摩托车发动机系统用加热型片式氧传感器（以下简称氧传感器）。

Heated planar oxygen sensor for motorcycle engine system

T/ZZB 3012-2022 汽车玻璃升降器控制开关

本文件规定了汽车玻璃升降器控制开关（以下简称“开关” ） 的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本文件适用于采用机械触碰的方式改变电路通断来控制玻璃升降器的开关。

Control switch of motor vehicles-Window regulator

T/QGCML 493-2022 数字高清全景摄像头

本文件规定了数字高清全景摄像头的术语和定义、命名规则、一般要求、电气性能要求、防护等级要求、机械性能要求、环境耐候性能要求、试验方法、检验规则、标识、包装、运输及贮存。 本文件适用于车用数字高清全景摄像头的生产与检验。

Digital HD panoramic camera

T/ZS 0319-2022 新能源电动汽车线束

前言　 1 范围　 2 规范性引用文件　 3 术语和定义　 4 原材料要求　 5 技术要求　 6 试验方法　 7 检验规则　 8 标志、包装、运输、贮存　

New energy electric vehicle wiring harness

T/QGCML 415-2022 汽车用聚氯乙烯绝缘单芯电线

本文件规定了汽车用聚氯乙烯绝缘单芯电线的术语和定义、一般要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于汽车用聚氯乙烯绝缘单芯电线的生产和设计。

PVC insulated single core wires for automobiles

KS R ISO 16844-3-2022 道路车辆 行驶记录仪系统 第3部分：运动传感器接口

Road vehicles－Tachograph systems－Part 3：Motion sensor interface

KS R ISO 14572-2022 道路车辆 圆形、护套、60 V 和 600 V 屏蔽和非屏蔽单芯或多芯电缆 基本和高性能电缆的试验方法和要求

Road vehicles — Round, sheathed, 60 V and 600 V screened and unscreened single- or multi-core cables — Test methods and requirements for basic- and high-performance cables

KS R ISO 16844-4-2022 道路车辆 行驶记录仪系统 第4部分：CAN接口

Road vehicles－Tachograph systems－Part 4：CAN interface

KS R ISO 16844-6-2022 道路车辆 行驶记录仪系统 第6部分：诊断

Road vehicles — Tachograph systems — Part 6: Diagnostics

KS R ISO 16844-7-2022 道路车辆 行驶记录仪系统 第7部分：参数

Road vehicles－Tachograph systems－Part 7：Parameters

KS R ISO 16844-1-2022 道路车辆 行车记录仪系统 第1部分：电连接器

Road vehicles－Tachograph systems－Part 1 : Electrical connectors

T/QGCML 384-2022 汽车空调电磁离合器及其关键零部件

本文件规定了汽车空调电磁离合器及其关键零部件(以下简称离合器)的术语和定义、工作环境、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于汽车空调电磁离合器及其关键零部件。

Automobile air conditioner electromagnetic clutch and its key components

T/CPSS 1001-2022 电动汽车大功率无线充电技术规范

该标准规定了11kW以上功率等级电动汽车无线充电系统的主要性能、通信要求、安全要求、辅助功能要求等，明确了大功率电动汽车无线充电系统的模块化要求和22kW以上与22kW以下功率等级的不同工作频率要求，给出了电动汽车大功率无线充电系统的地面推荐设备与车载推荐设备，补充了目前国际、国内、行业标准中11kW以上功率等级的电动汽车无线充电系统技术规范尚不完善与尚待明确的内容，实现了该功率等级无线充电系统“有标准可依”，具有重大的现实意义和社会效益，充分发挥了团体标准的规范与引领作用，有利于电动汽车大功率无线充电系统产业化发展。

Technical specification for high-power wireless charging of electric vehicles

BS ISO 21111-8:2022 公路车辆 车载以太网 电气 100Mbit/s 以太网传输介质、组件和测试

1   Scope This document defines various parameters to be tested for the communication channel between two Ethernet devices (e.g. ECUs for automotive application) and also for the transmission media including cables and connectors as a single component of which the communication channel consists. This document also specifies the general RF requirements for a physical layer communication channel for ISO/IEC/IEEE 8802‑3. These requirements are related to signal integrity of the communication channel. Test methods for electrical performances of the communication channel/link and cables and connectors are also specified in this document.

Road vehicles. In-vehicle Ethernet - Electrical 100-Mbit/s Ethernet transmission media, components and tests

ISO 21111-8:2022 道路车辆.车内以太网.第8部分:电气100Mbit/s以太网传输介质、部件和试验

This document defines various parameters to be tested for the communication channel between two Ethernet devices (e.g. ECUs for automotive application) and also for the transmission media including cables and connectors as a single component of which the communication channel consists. This document also specifies the general RF requirements for a physical layer communication channel for ISO/IEC/IEEE 8802-3. These requirements are related to signal integrity of the communication channel. Test methods for electrical performances of the communication channel/link and cables and connectors are also specified in this document.

Road vehicles — In-vehicle Ethernet — Part 8: Electrical 100-Mbit/s Ethernet transmission media, components and tests

BS ISO 16844-7:2022 公路车辆 行驶记录仪系统 参数

1   Scope This document specifies the parameters used on the service interface of the recording equipment. Some of them are specified in detail in this document, while others are given in the ISO 14299 series.

Road vehicles. Tachograph systems. Parameters

BS ISO 21448:2022 公路车辆 预期功能的安全性

What is ISO 21448 - Safety of the intended functionality about? The automotive industry is producing more and more vehicles with increased levels of automation. These require new safety standards, including ISO 21448 which is a new international standard dealing with potentially hazardous behaviours caused by the performance limitations of an electronic or electrical system, or its intended functionality. This known as the safety of the intended functionality (SOTIF), which is distinct from functional safety in the event of systems failures – which is covered in the BS ISO 26262 series. Who is ISO 21448 - Safety of the intended functionality for? Vehicle manufacturers Tier one suppliers e.g. of electrical and electronic devices for vehicles connectivity, safety and driving functionality Tier two suppliers e.g. of processing chip, CAN BUS devices and sensor devices Software developers of software supporting both safety functions such as ADAS, and CAN BUS interfaces (J1939, OBD2) Safety consultants Formal training suppliers for the automotive industry Certification agencies Regulations and vehicle type approval agencies Vehicle aftermarket Academia

Road vehicles. Safety of the intended functionality

BS ISO 16844-2:2022 公路车辆 行驶记录仪系统 记录单元通讯接口

1   Scope This document specifies the electrical interfaces of the data and the service interfaces. The electrical interfaces to the CAN-based in-vehicle networks are not in the scope of this document.

Road vehicles. Tachograph systems. Recording unit communication interface