43.040.10 电气和电子设备 标准查询与下载

T/ZZB 1810-2020 汽车空调风机

本文件规定了汽车空调风机（以下简称风机）的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、贮存和保管、质量承诺。 本文件适用于有刷电机式汽车空调风机。

Vehicle air conditioning fan

DS/ISO 21111-2:2020 道路车辆《车载以太网》第2部分：通用物理实体要求

Road vehicles – In-vehicle Ethernet – Part 2: Common physical entity requirements

DS/ISO 21111-1:2020 道路车辆“车载以太网”第1部分：一般信息和定义

Road vehicles – In-vehicle Ethernet – Part 1: General information and definitions

T/ZZB 1783-2020 机动车用机械式电喇叭

本文件规定了直流电源供电的机动车用机械式电喇叭的术语和定义、分类、型号编制及基本参数、基本要求、技术要求、试验方法、检验规则、标志、包装、储存和质量承诺。 本文件适用于M、N、L3、L4、L5类机动车用机械式电喇叭(以下简称电喇叭)。 本文件不适用于优先通行的车辆，例如警车、救护车、消防车、工程抢险车等所使用发出一系列不同频率声音的声响装置。

Mechanical electric horn for motor vehicles

BS ISO 21111-1:2020 公路车辆 车载以太网 一般信息和定义

What is ISO 21111 ‑ 1 about?    ISO 21111 ‑ 1 is part one of the multi-series standard that defines the terms which are used in the ISO 21111 series and provides an overview of the standards for in-vehicle Ethernet including the complementary relations to ISO/IEC/IEEE 8802 ‑ 3:2017 [7] and its amendments, ISO 21111 ‑ 1 structure in accordance with OSI reference model specified in ISO/IEC 7498 ‑ 1 [1] and ISO/IEC 10731:1994 ,[2] type of physical entities, in-vehicle Ethernet specific functionalities, and so on.

Road vehicles. In-vehicle Ethernet - General information and definitions

ISO 21111-2:2020 公路车辆 车内以太网 第二部分 通用物理实体要求

This document specifies the following items to complement ISO/IEC /IEEE 8802-3: — interface between reconciliation sublayer and physical entity including reduced gigabit media independent interface (RGMII); — common physical entity wake-up and synchronised link sleep functionalities independent from physical media and transmission bit rate. The optical and electrical component requirements and test methods for optical and electrical transmission of in-vehicle Ethernet are not in the scope of this document.

Road vehicles — In-vehicle Ethernet — Part 2: Common physical entity requirements

ISO 21111-1:2020 道路车辆 - 车载以太网 - 第1部分:一般信息和定义

Road vehicles — In-vehicle Ethernet — Part 1: General information and definitions

T/ZZB 1721-2020 汽车点火用霍尔式位置传感器

本文件规定了汽车点火用霍尔式位置传感器的术语和定义、产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存及质量承诺。 本文件适用于汽车发动机点火用霍尔式凸轮轴位置传感器和霍尔式曲轴位置传感器（以下简称传感器）。

Hall position sensor for automobile ignition

T/ZZB 1688-2020 汽车电子油门踏板总成

本文件规定了汽车电子油门踏板总成的术语和定义、分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本文件适用于非接触式商用车、乘用车用电子油门踏板总成。

Automotive electrical accelerator pedal module

BS ISO 21780:2020 公路车辆 电源电压 48 V 电气要求和测试

What is ISO 21780 about?    ISO 21780 is an international standard on-road vehicle that specifies the electrical requirements and test methods on electric and electronic components used in road vehicles that can provide safety, quality, and reliability to users.   ISO 21780 covers an electrical system operating at a nominal voltage of 48 V DC.   This includes the following:   General requirements on 48 V DC electrical systems  

Road vehicles. Supply voltage of 48 V. Electrical requirements and tests

T/CPSS 1010-2020 电动汽车运动过程无线充电方法

本标准规定了电动汽车在特定场景下移动式无线充电类系统总体要求、主要性能的技术要求（标准所列出的内容）等。

Dynamical wireless charging standard for moving electric vehicle

ISO 21780:2020 道路车辆.48V电源电压.电气要求和试验

This document covers requirements and tests for the electric and electronic components in road vehicles equipped with an electrical system operating at a nominal voltage of 48 V DC. This includes the following: — general requirements on 48 V DC electrical systems; — voltage ranges; — slow voltage transients and fluctuations (not including EMC).

Road vehicles — Supply voltage of 48 V — Electrical requirements and tests

BS ISO 25981:2020 公路车辆 用于牵引和被牵引车辆电气连接的连接器 适用于标称电源电压为 12 V 或 24 V 的电子监控充电系统的连接器

What is ISO 25981 about?    ISO 25981 is an international standard on road vehicles that guides you to establish electrical connections of charging systems of towing vehicles.   ISO 25981 specifies dimensional characteristics, contact allocation, tests and requirements of 7-pole connectors for electrical connections of electronically monitored charging systems of towing and towed vehicles. The electronic monitoring system is designed to detect 12 V and 24 V nominal supply voltage and to limit the current to 50 A, and this is a connector without any braking capacity.   This electrical connection is intended for use with separable truck-trailer combinations in order to connect an additional battery pack of the trailer with the generator of the truck using an electronically monitored charging system  

Road vehicles. Connectors for the electrical connection of towing and towed vehicles. Connectors for electronically monitored charging systems with 12 V or 24 V nominal supply voltage

BS ISO 21111-5:2020 公路车辆 车载以太网 光纤 1-Gbit/s 物理层系统要求和测试计划

What is ISO 21111 ‑ 5 about?    ISO 21111 ‑ 5 is part five of the multi-series standard that specifies:   Requirements on the physical layer at system level   Requirements on the interoperability test set-ups   Interoperability test plan that checks the requirements for the physical layer at system level   Requirements on the device-level physical layer conformance test set-ups  

Road vehicles. In-vehicle Ethernet - Optical 1-Gbit/s physical layer system requirements and test plans

BS ISO 19453-6:2020 公路车辆 电力推进车辆驱动系统电气电子设备的环境条件和测试-牵引电池组和系统

What is ISO 19453 ‑ 6 about?    ISO 19453 ‑ 6 is the sixth part of the ISO 19453 series of documents.  ISO 19453 ‑ 6 specifies requirements for lithium-ion traction battery packs or systems used in battery electric, hybrid electric, and fuel cell electric road vehicles.    ISO 19453 ‑ 6 describes the most relevant environmental stresses and spe...

Road vehicles. Environmental conditions and testing for electrical and electronic equipment for drive system of electric propulsion vehicles - Traction battery packs and systems

ISO 25981:2020 道路车辆 - 用于牵引和牵引车辆电气连接的连接器 - 具有12 V或24 V标称电源电压的电子监控充电系统连接器

This document specifies dimensional characteristics, contact allocation, tests and requirements of 7-pole connectors for electrical connections of electronically monitored charging systems of towing and towed vehicles. The electronic monitoring system is designed to detect 12 V and 24 V nominal supply voltage and to limit the current to 50 A, and this is a connector without any braking capacity. This electrical connection is intended for use with separable truck-trailer combinations in order to connect an additional battery pack of the trailer with the generator of the truck using an electronically monitored charging system. Additional battery packs in trailers are basically used with tailgate lifts, electrical forklifts or other technical equipment with high current consumption. This document further specifies a park socket used to receive and store the plug when it is disconnected.

Road vehicles — Connectors for the electrical connection of towing and towed vehicles — Connectors for electronically monitored charging systems with 12 V or 24 V nominal supply voltage

ISO 19453-6:2020 道路车辆.电动推进车辆驱动系统用电气和电子设备的环境条件和试验.第6部分:牵引电池组和系统

This document specifies requirements for lithium-ion traction battery packs or systems used in battery electric, hybrid electric and fuel cell electric road vehicles. This document describes the most relevant environmental stresses and specifies tests and test boundary conditions. This document establishes a classification of battery packs or systems and defines different stress levels for testing when a classification is applicable and required. The objective of this document is to specify standard test procedures and conditions to enable the observation of the reliability of the lithium-ion traction battery in the vehicle. This document specifies tests for a battery pack or system of voltage class A and B. This document provides the necessary information to set up a dedicated test plan for a battery pack or system subject to agreement between the customer and supplier. If required, the relevant test procedures and/or test conditions can also be selected from this document. NOTE This document only covers requirements and test conditions for a traction battery pack or system used in passenger cars.

Road vehicles — Environmental conditions and testing for electrical and electronic equipment for drive system of electric propulsion vehicles — Part 6: Traction battery packs and systems

IEC 62321-3-2:2020 电工产品中某些物质的测定第3-2部分:用燃烧离子色谱法（C-IC）筛选聚合物和电子产品中的氟、溴和氯

Determination of certain substances in electrotechnical products - Part 3-2: Screening - Fluorine, bromine and chlorine in polymer and electronics by combustion-ion chromatography (C-IC)

BS ISO 8820-11:2020 公路车辆 熔断体 带凸片的熔断体（刀片式）M 型（中高电流）

What is ISO 8820 ‑ 11 about?    ISO 8820 ‑ 11 is part 11 of the multi-series standard that specifies fuse-links with tabs (blade-type) Type M (medium-high current) for use in road vehicles. ISO 8820 ‑ 11 establishes, for this fuse-link type, the rated current, test procedures, performance requirements and dimensions.   ISO 8820 ‑ 11 is applicable for fuse-links with a rated voltage of 32 V and a current rating of ≤80 A and a breaking capacity of 1 000 A intended for use in road vehicles.   ISO 8820 ‑ 11 is intended to be used in conjunction with ISO 8820-1 and ISO 8820-2 . The numbering of the clauses corresponds to that of ISO 8820-1 whose requirements are applicable, except where modified by requirements particular to

Road vehicles. Fuse-links - Fuse-links with tabs (blade type) Type M (medium-high current)

BS ISO 12098:2020 公路车辆 用于牵引和被牵引车辆电气连接的连接器 适用于标称电源电压为 24 V 的车辆的 15 针连接器

What is ISO 12098 about?    ISO 12098 gives the dimensions of, and specifies the contact allocation and tests and test   requirements for 15-pole connectors for the electrical connection of equipment other than braking systems and running gear of towing and towed vehicles with 24 V nominal supply voltage. ISO 12098 specifies a park socket used to receive and store the plug when disconnected, and a means of adaptation between 7-pole and 15-pole connectors.   Who is ISO 12098 for?   ISO 12098 on 15-pole connector for vehicles with 24 V nominal supply voltage   is useful for:   Towing vehicles manufacturers   

Road vehicles. Connectors for the electrical connection of towing and towed vehicles. 15-pole connector for vehicles with 24 V nominal supply voltage