43.040.20 照明、信号和警告设备 标准查询与下载

SAE J581-2011 辅助远光灯

This SAE Standard provides test procedures, performance requirements and guidelines for auxiliary high beam lamps.

Auxiliary High Beam Lamps (Stabilized Type)

SAE J2282-2011 分布式照明系统(DLS)

This SAE Recommended Practice applies to motor vehicle distributed lighting systems (DLS) which use light generated by remote sources. It provides test methods, requirements, and guidelines applicable to these systems. This document is intended to be a guide to standard practice and is subject to change dependent upon additional experience and technical advances. This document covers Headlamp, Fog lamp, Auziliary lamp, plus Signal and Marking lamp functions.

Distributed Lighting Systems (DLS) (Stabilized Type)

SAE J1606-2011 成年驾驶员前照灯设计指南

This SAE Information Report should be used as a supplement to SAE J1383. It is intended to provide additional information which is important to the automotive designer and engineer in the process of designing, developing, and engineering the headlamps of motor vehicles which will take into account the effects of the aging process on the driver.

Headlamp Design Guidelines for Mature Drivers (Stabilized Type)

SAE J1735-2011 协调的车辆前照灯性能要求

This SAE Recommended Practice provides headlamp beam patter test points for harmonized low and high beam headlamp beam patterns that incorporate elements of European, Asian, and U.S. photometric tables. These photometric tables are optional to those found in SAE J 1383.

Harmonized Vehicle Headlamp Performance Requirements (Stabilized Type)

SAE J591-2011 聚光灯

This SAE Standard provides test procedures and performance requirements for spot lamps.

Spot Lamps (Stabilized Type)

SAE J2087-2011 昼行灯

This SAE Recommended Practice provides test procedures, requirements, and guidelines for a daytime running light (DRL) function.

Daytime Running Light

GSO ECE 7:2010 车辆（摩托车除外）及其挂车后、前（侧）灯、制动灯、端标志灯位置审批统一要求

This Regulation applies to: 0.1. front and rear position (side) lamps and stop lamps for vehicles of categories L, M, N, O and T 1/; and, 0.2. end-outline marker lamps for vehicles of categories M, N, O and T. _________________ 1/ As defined in Annex 7 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), (document TRANS/WP.29/78/Rev.1/Amend.2 as last amended by Amend.4)." Paragraph 4.2.1.1., the reference to footnote 1/ and footnote 1/, renumber as footnote 2/ and amend to read: "2/ 1 for Germany, .... 10 for Serbia, .... 48 for New Zealand, 49 for Cyprus, 50 for Malta, 51 for the Republic of Korea, 52 for Malaysia, 53 for Thailand, 54 and 55 (vacant) and 56 for Montenegro. Subsequent numbers shall be assigned ...." Paragraph 6.1. (the table), the reference to footnote 1/ and footnote 1/, renumber as footnote 3/. Paragraph 6.1. (the table), the reference to footnote 2/ and footnote 2/, renumber as footnote 4/. Paragraph 7.2., the reference to footnote 2/ and footnote 2/, renumber as footnote 5/. - - - - -

Uniform provisions concerning the approval of front and rear position (side) lamps, stop-lamps and end-outline marker lamps for motor vehicles (except motor cycles) and their trailers

GSO ECE 19:2010 汽车前雾灯

This Regulation applies to front fog lamps for vehicles of categories L3, L4, L5, L7, M, N, and T. 2/

Motor vehicles front fog lamps

GSO ECE 119:2010 批准购置机动车灯具的标准要求

This Regulation applies to cornering lamps for vehicles of categories M, N and T 1/.

Uniform provisions concerning the approval of cornering lamps for power-driven vehicles

GSO ECE 38:2010 汽车后雾灯

This Regulation applies to rear fog lamps for vehicles of categories L3, L4, L5, L7, M, N, O, and T. 1/

Motor vehicles rear fog lamps

SAE J2111-2010 前照灯清洁器

This SAE Recommended Practice provides test procedures, performance requirements, and guidelines for cleaners intended for use on motor vehicles.

Headlamp Cleaners

SAE J1373-2010 全长低于9.1 m的电动机车用后角灯

This SAE Recommended Practice provides test procedures, requirements, and guidelines for rear cornering lamps for use on vehicles less than 9.1 m in overall length.

Rear Cornering Lamps for Use on Motor Vehicles Less Than 9.1 m in Overall Length

SAE J593-2010 倒车灯(倒车灯)

This SAE Standard provides installation requirements, test procedures, design guidelines, and performance requirements for backup/reversing lamp.

Backup Lamp (Reversing Lamp)

SAE J1319-2010 后雾灯系统

This SAE Recommended Practice provides test procedures, requirements, and guidelines for fog tail lamp systems.

Rear Fog Lamp Systems

SAE J96-2010 工业设备用闪烁警示灯

This SAE Standard covers the general requirements and the test requirements for a flashing warning lamp for industrial wheeled equipment.

Flashing Warning Lamp for Industrial Equipment

SAE J1383-2010 机动车辆前照灯性能要求

This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements for headlamps.

Performance Requirements for Motor Vehicle Headlamps

SAE J1432-2010 总体宽度等于或超过2032mm的车辆中使用的背面高安装的停止灯和背面高安装的转弯信号灯

This SAE Recommeded Practice provides test procedures, requirements, and guidelines for high-mounted stop lamps and high-mounted turn signal lamps intended for use on vehicles 2032 mm or more in overall width. This document applies to trucks, motor coaches, van type trailers, and other vehicles with permanent structure greater than 2800 mm high. This document does not apply to school buses, truck tractors, pole trailers, flat-bed trailers, pick-up truck with dual wheels and trailer converter dollies. The purpose of the high-mounted stop lamp(s) and high-mounted turn signal lamp(s) is to provide a signal over intervening vehicles to the driver of following vehicles.

Rear High Mounted Stop Lamps and Rear High Mounted Turn Signal Lamps for Use on Vehicles 2032 mm or More in Overall Width

SAE J567-2010 照明电源固位系统

This SAE Standard references the performance and functional requirements of the International Electrotechnical Commission (IEC) and its U.S. member, the American National Standards Institute (ANSI). By referring to IEC/ANSI and its standards concerning light source (bulb) sockets, light source (lamp) holders, and gages, this document recognizes the need for harmonized standards world-wide for what are typically commodity items. Additional requirements are noted.

Lamp Source Retention System

SAE J2040-2010 总体宽度在2032mm和以上的车辆用尾灯(后位置尾灯)

This SAE Standard provides test procedures, requirements, and guidelines for tail lamps intended for use on vehicles 2032 mm or more in overall width. Tail lamps conforming to the requirements of this document may also be used on vehicles less than 2032 mm in overall width.

Tail Lamps (Rear Position Lamps) for Use on Vehicles 2032 mm or More in Overall Width

SAE J575-2010 总体宽度小于2032mm的机动车辆用照明装置及元件的试验方法和设备

This SAE Recommended Practice is intended as a quide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provided standardized laboratory tests, test methods and equipment, and requirements for lighting devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in J2139. Device specific tests and requirements can be found in applicable SAE technical reports.

Test Methods and Equipment for Lighting Devices for Use on Vehicles Less Than 2032 mm in Overall Width