43.040.20 照明、信号和警告设备 标准查询与下载

SAE J2338-2010 SAE 工作组关于前照灯安装高度的建议

The SAE International task force on headlamp mounting height has considered the ramificaitons of reducing the maximum mounting height of headlamps on highway vehicles. The task force has concluded that it is the best interest of the driving public to make a substantial reduction in the recommended maximum height at which headlamps, particularly lower beam headlamps, may be mounted. Heights as low as 36 to 40 in (90 to 100 cm) have been considered. New tractor vehicles are in fact being designed with headlamps mounted in this range. Further recommendations were withheld in anticipation of tests to demonstrate the effect of mounting height on the legibility of certain overhead signs.

Recommendations of the SAE Task Force on Headlamp Mounting Height

SAE J594-2010 反射板

This SAE Standard provides test procedures, requirements, and guidelines for reflex reflectors.

Reflex Reflectors

SAE USCAR15-3-2010 测试汽车电灯泡插座用规范

Specification for testing automotive light bulb sockets

SAE USCAR3-3-2010 机动车小型灯泡的测试标准

Standard for testing automotive miniature bulbs

SAE J2261-2010 总体宽度等于或大于2032 mm的机动车辆用刹车灯和前后转弯信号灯

This SAE Standard provides test procedures, requirements, and guidelines for stop lamps and turn signal lamps intended for use on vehicles 2032 mm or more in overall width. Stop lamps and front- and rear-turn signal lamps conforming to the requirements of this document may be used on vehicles less than 2032 mm in overall width.

Stop Lamps and Front- and Rear-Turn Signal Lamps for Use on Motor Vehicles 2032 mm or More in Overall Width

SAE USCAR15-2010 测试汽车电灯泡插座用规范

This specification establishes the requirements and test procedures for automotive miniature bulb retention devices, including wedge base sockets with integral connector, direct wire wedge base sockets, circuit plate assemblies, and associated interfaces. Tests shall follow the sequence shown in the flow charts in Appendix E whenever the following occurs: New design; Design, material or process change made to an existing device, which could affect the outcome of the test. The test sequence shown in Appendix F shall be run annually.

Specification for testing automotive light bulb sockets

SAE USCAR3-2010 机动车小型灯泡的试验标准

The procedures contained in this specification cover the laboratory testing of miniature incandescent bulbs for use in automotive illumination and signaling applications. The following tests shall be run whenever the following occurs: New bulb design; Design or process change made to an existing bulb, which could affect the outcome of the test. The completion of one calendar year as noted in the following Test Schedule Table. Process control data is acceptable.

Standard for testing automotive miniature bulbs

DIN EN 60809:2009 道路车辆灯.尺寸,电气和亮度要求(IEC 60809:1995+A1:1996+A2:2002+A3:2004+A4:2009),德文版本EN 60809:1996+A1:1996+A2:2002+A3:2004+A4:2009

Lamps for road vehicles - Dimensional, electrical and luminous requirements (IEC 60809:1995 + A1:1996 + A2:2002 + A3:2004 + A4:2009); German version EN 60809:1996 + A1:1996 + A2:2002 + A3:2004 + A4:2009

SAE USCAR34-2009 试验性车灯装配规范

Specification for testing automotive lamp assemblies

SAE J914-2009 长度小于12 m的车辆用侧转向灯

This SAE Standard provides installation requirements, test procedures, design guidelines, and performance requirements for side turn signal lamps for vehicles less than 12 m in length.

Side Turn Signal Lamps for Vehicles Less Than 12 m in Length

NF R13-629/A4:2009 陆地起床灯.尺寸,电力和照明要求

Lamps for road vehicles - Dimensional, electrical and luminous requirements.

SAE J2121-2009 施工和供工业机械中的组合照明装配的要求

This SAE Standard provides general design performance requirements and related test procedures for composite lighting unit assemblies, other than signaling and marking devices, used on Earthmoving, Agricultural Tractors, and Road Building and Maintenance off-road work machines as defined in SAE J1116. To provide general guidelines and design parameters for lighting assemblies used on construction and industrial machinery.

Requirements for Composite Lighting Assemblies Used on Construction and Industrial Machinery

SANS 20048:2009 与照明及光信号设备安装相关车辆的许可有关的统一规定

Applies to vehicles of categories M, N, and to their trailers (category O) with regard to the installation of lighting and light-signalling devices.

Uniform provisions concerning the approval of vehicles with regard to the installation of lighting and light-signalling devices

TIS 1788-2008 机动车辆用前照灯清洗装置

Headlamp cleaners for power.driven vehicles

SAE J852-2009 用于机动车辆的前拐弯灯

This SAE Recommended Practice provides test procedures, performance requirements, and guidelines for front cornering lamps intended for use on motor vehicles.

Front Cornering Lamps for Use on Motor Vehicles

SAE J994-2009 警报备用电气实验室性能试验

The scope of this SAE Standard is the definition of the functional, environmental, and life cycle test requirements for electrically operated backup alarm devices primarily intended for use on off-road, self propelled work machines as defined by SAE J1116 (limited to categories of 1) construction, and 2) general purpose industrial). This purpose of this document is to define a set of performance requirements for backup alarms, independent of machine usage. The laboratory tests defined in this document are intended to provide a uniform and repeatable means of verifying that a test alarm meets the stated requirements. For on machine requirements and test procedures, refer to SAE J 1446.

Alarm Backup Electric Laboratory Performance Testing

SAE J592-2009 全宽小于2032mm的道路车辆用边侧标志灯

This SAE Standard provides test procedures, requirements, and guidelines for sidemarker lamps for vehicles less than 2032 mm in overall width.

Sidemarker Lamps for Use on Road Vehicles Less Than 2032 mm in Overall Width

IEC 60809:1995/AMD4:2009 修改件4.道路车辆用灯具.尺寸、电气和发光要求

Amendment 4 - Lamps for road vehicles - Dimensional, electrical and luminous requirements

SAE HS-34-2009 SAE地面车辆照明标准手册2009年版

The SAE Ground Vehicle Lighting Manual provides a comprehensive compilation of SAE Technical Reports relating to the design, engineering, testing, inspection and installation of motor vehicle lighting and signalling equipment. The basic standards and recommended practices in the Manual are those developed under the auspices of the SAE Lighting Committee.

SAE Ground Vehicle Lighting Standards Manual 2009 Edition

NF R13-630/A1:2009 道路车辆用灯.性能要求

Lamps for road vehicles - Performance requirements.