43.040.20 照明、信号和警告设备 标准查询与下载
共找到 652 条与 照明、信号和警告设备 相关的标准，共 44 页
Applies to lamps intended to increase conspicuity of a vehicle in daylight.
Uniform provisions concerning the approval of daytime running lamps for power-driven vehicles
- ICS
- 43.040.20
- CCS
- T38
- 发布
- 2005-06-03
- 实施
This SAE Recommended Practice provides test procedures, requirements, and guidelines for fog tail lamp systems.
Fog Tail Lamp (Rear Fog Light) Systems
- ICS
- 43.040.20
- CCS
- T38
- 发布
- 2005-05-25
- 实施
- 2010-08-19
1.1 These requirements apply to incandescent and fluorescent low-voltage luminaires, rated 24 volts or less, of the surface mounted or recessed type intended for permanent installation in recreational vehicles in accordance with Article 551 of the National Electrical Code, NFPA 70. 1.2 These requirements do not apply to running or clearance lights intended to be mounted on the exterior of a recreational vehicle. This new edition of ANSI/UL 234 is issued to update the title of the standard and to replace the terminology from "fixure" to "luminaires." This new edition also includes a clarification of the flammability rating.
UL Standard for Safety Low Voltage Lighting Fixtures for Use in Recreational Vehicles Fifth Edition; Reprint with revisions through and including October 31, 2007
- ICS
- 43.040.20
- CCS
- T38
- 发布
- 2005-01-21
- 实施
Uniform provisions concerning the approval of motor vehicle headlamps emitting a symmetrical passing beam or a driving beam or both and equipped with filament lamps
- ICS
- 43.040.20
- CCS
- 发布
- 2005
- 实施
- 2006-07-01
This bulletin contains substantive changes to UL 234 based on comments received to the ballot of the proposed Fifth Edition, bulletin dated March 19, 2004.
Standard for Safety for Low Voltage Lighting Fixtures for Use in Recreational Vehicles
- ICS
- 43.040.20
- CCS
- T38
- 发布
- 2005
- 实施
Uniform provisions concerning the approval of motor vehicle headlamps emitting an asymmetrical passing beam or a driving beam or both and equipped with filament lamps
- ICS
- 43.040.20
- CCS
- 发布
- 2005
- 实施
- 2006-07-01
이 규격은 동력 구동 차량용[오토바이 제외(1)] 점멸기 시료를 무작위로 취할 때 확인한
Road vehicles－Motor vehicles－Production conformityrequirements for flasher units
- ICS
- 43.040.20
- CCS
- G41
- 发布
- 2004-12-31
- 实施
- 2004-12-31
Road vehicles－Motor vehicles－Flasher units
- ICS
- 43.040.20
- CCS
- 发布
- 2004-12-31
- 实施
Road vehicles－Measurement of variations in dipped-beamheadlamp angle as a function of load
- ICS
- 43.040.20
- CCS
- 发布
- 2004-12-31
- 实施
이 규격은 자동차용 점멸 장치의 인증에 필요한 전기적 특성에 대해 정의한다.
Road vehicles－Motor vehicles－Flasher units
- ICS
- 43.040.20
- CCS
- T35
- 发布
- 2004-12-31
- 实施
- 2004-12-31
Road vehicles－Installation of lighting and light signalling devicesfor motor vehicles and their trailers
- ICS
- 43.040.20
- CCS
- 发布
- 2004-12-31
- 实施
Road vehicles－Working voltages for lights fitted to motorvehicles and to their trailers
- ICS
- 43.040.20
- CCS
- 发布
- 2004-12-31
- 实施
Road vehicles－Motor vehicles－Production conformityrequirements for flasher units
- ICS
- 43.040.20
- CCS
- 发布
- 2004-12-31
- 实施
Road vehicles－Levelling devices for headlamp dipped beam
- ICS
- 43.040.20
- CCS
- 发布
- 2004-12-31
- 实施
Road vehicles－Alarm systems for buses and commercialvehicles of maximum authorized total mass greater than 3.5 t
- ICS
- 43.040.20
- CCS
- 发布
- 2004-12-30
- 实施
이 규격은 최대 허용 총 질량(ISO 1176에서 정의된 것처럼 코드 ISO-M08)이 3
Road vehicles-Alarm systems for buses and commercialvehicles of maximum authorized total mass greater than 3.5 t
- ICS
- 43.040.20
- CCS
- A25
- 发布
- 2004-12-30
- 实施
- 2004-12-30
This International Standard specifies the dimensions of special warning lamps for road vehicles, in order to ensure interchangeability and accurate positioning, bearing in mind the rapid change of light intensity from such devices in a vertical cross-section of the projected beam. It also specifies (see Annex A) methods for testing the magnetic-base mountings used to install special warning lamps directly on the steel sheet of the roof or body of a vehicle (special warning lamps of Category D). NOTE In certain countries and international bodies, the term “light” is sometimes used instead of “lamp”.
Road vehicles - Special warning lamps - Dimensions
- ICS
- 43.040.20
- CCS
- T38
- 发布
- 2004-11-19
- 实施
- 2004-11-19
This International Standard specifies the dimensions of special warning lamps for road vehicles, in order to ensure interchangeability and accurate positioning, bearing in mind the rapid change of light intensity from such devices in a vertical cross-section of the projected beam. It also specifies (see Annex A) methods for testing the magnetic-base mountings used to install special warning lamps directly on the steel sheet of the roof or body of a vehicle (special warning lamps of Category D). NOTE In certain countries and international bodies, the term “light” is sometimes used instead of “lamp”.
Road vehicles - Special warning lamps - Dimensions
- ICS
- 43.040.20
- CCS
- T38
- 发布
- 2004-11
- 实施
This SAE Standard provides test procedures, requirements, and guidelines for reflex reflectors used on vehicles 2032 mm or more in overall width. Reflex reflectors conforming to these requirements may also be used on vehicles less than 2032 mm in overall width.
Reflex Reflectors for use on Vehicles 2032 mm or More in Overall Width
- ICS
- 43.040.20
- CCS
- T26
- 发布
- 2004-10-18
- 实施
Covers the measurement of the sound level of audible warning devices after these have been installed in motor vehicles of categories other than category L.
Determining the performance of audible warning devices (hooters) after installation in a motor vehicle
- ICS
- 43.040.20
- CCS
- T36
- 发布
- 2004-09-03
- 实施
