43.040.20 照明、信号和警告设备 标准查询与下载

SAE J2510-2003 统一前雾灯

This SAE recommended practice provides performance requirements, test procedures, and design and installation guidelines for front fog lamps that harmonize with international front fog lamp requirements.

Harmonized Front Fog Lamp

BS EN 60810+A1:2003 道路车辆用灯 性能要求

Lamps for road vehicles - Performance requirements

BS EN 60810:2003+A2:2013 道路车辆用灯具. 性能要求

Lamps for road vehicles - Performance requirements

SAE J994-2003 报警后备电实验室性能测试

The scope of this SAE Standard is the definition of the functional, environmental, and life cycle test requirements for electrically operated backup alarm devices primarily intended for use on off-road, self propelled work machines as defined by SAE J1116 (limited to categories of 1) construction, and 2) general purpose industrial). This purpose of this document is to define a set of performance requirements for backup alarms, independent of machine usage. The laboratory tests defined in this document are intended to provide a uniform and repeatable means of verifying whether or nor a test alarm meets the stated requirements. For on-machine requirements and test procedures, refer to SAE J 1446.

Alarm Backup Electric Laboratory Performance Testing

SAE J591-2003 聚光灯

This SAE Standard provides test procedures and performance requirements for spot lamps.

Spot Lamps

SAE J587-2003 牌照照明设备(后牌照照明设备)

This SAE Standard provides test procedures, requirements, and guidelines for vehicular license plate illumination devices.

License Plate Illumination Devices (Rear Registration Plate Illumination Devices)

KS R ISO 7588-1:2003 道路车辆.电/电子开关设备.第1部分:继电器和闪光器

이 규격은 도로 차량에 사용되는 릴레이 및 점멸 장치 단자의 치수 특성 및 기능을 규정

Road vehicles－Electrical/electronic switching devices－Part 1：Relays and flashers

KS R ISO 7588-1-2003(2023) 道路车辆电气/电子开关装置第1部分:继电器和闪光灯

Road vehicles－Electrical/electronic switching devices－Part 1：Relays and flashers

KS R ISO 7588-1-2003(2018) 道路车辆电气/电子开关装置第1部分:继电器和闪光灯

Road vehicles－Electrical/electronic switching devices－Part 1：Relays and flashers

DLA A-A-59349 VALID NOTICE 1-2003 装有支架的反光镜

A-A-59349, dated 9 October 1998, has been reviewed and determined to be valid for use in acquisition

REFLECTORS, LIGHT; WITH HOLDER

ISO 303:2002/cor 1:2003 道路车辆.汽车及其挂车的照明和光信号装置的安装.技术勘误1

This is Technical Corrigendum 1 to ISO 303-2001 (Road vehicles — Installation of lighting and light signalling devices for motor vehicles and their trailers )

Road vehicles - Installation of lighting and light signalling devices for motor vehicles and their trailers; Technical Corrigendum 1

SAE J2400-2003 前向碰撞预警系统的人为因素:工作特性和用户界面的要求

Forward Collision Warning (FCW) systems are onboard systems intended to provide alerts to assist drivers in avoiding striking the rear end of another moving or stationary motorized vehicle. This SAE Information Report describes elements for a FCW operator interface, as well as requirements and test methods for systems capable of warning drivers of rear-end collisions. This information report applies to original equipment and aftermarket FCW systems for passenger vehicles including cars, light trucks, and vans. This report does not apply to heavy trucks. Furthermore, this document does not address integration issues associated with adaptive cruise control (ACC), and consequently, aspects of the document could be inappropriate for an ACC system integrated with a FCW system.

Human Factors in Forward Collision Warning Systems: Operating Characteristics and User Interface Requirements

SAE J914-2003 长度小于 12 m 的车辆的侧转向信号灯

This SAE Standard provides installation requirements, test procedures, design guidelines, and performance requirements for side turn signal lamps for vehicles less than 12 m in length.

Side Turn Signal Lamps for Vehicles Less Than 12 m in Length

KS R 5065-2003 汽车号牌板灯试验

이 규격은 자동차용 번호등 테스터(이하 테스터라고 한다.)에 대하여 규정한다.

License plate lamp testers for automobiles

KS R 5065-2003(2013) 牌照灯测试人员AUTOMOBILES

License plate lamp testers for automobiles

SAE J2042-2003 用于总宽度为 2032 毫米或以上的机动车辆的间隙灯、侧标志灯和识别灯

This SAE Standard provides test procedures, requirements, and guidelines for clearance, sidemarker, and identification lamps intended for use on vehicles 2032 mm or more in overall width. A clearance lamp, sidemarker lamp, or an identification lamp conforming to the requirements of this document may be used on vehicles less than 2032 mm in overall width.

Clearance, Sidemarker, and Identification Lamps for Use on Motor Vehicles 2032 mm or More in Overall Width

SAE J99-2003 公路上工业设备的照明和标记

To provide specifications for lighting and marking of industrial wheeled equipment whenever such equipment is operated or traveling on a highway.

Lighting and Marking of Industrial Equipment on Highways

IEC 60810:2003 道路车辆用灯.性能要求

This International Standard is applicable to replaceable lamps (filament lamps and discharge lamps) to be used in headlamps, fog-lamps and signalling lamps for road vehicles. It is especially applicable to those lamps which are listed in IEC 60809. However, the standard may also be used for other lamps falling under the scope of this standard, as well as for future developments, e.g. such where the light is produced by light emitting diodes (LED). It specifies requirements and test methods for the measurement of performance charac-teristics such as lamp life, lumen maintenance, torsion strength, glass bulb strength and resistance to vibration and shock. Moreover, information on temperature limits, maximum lamp outlines and maximum tolerable voltage surges is given for the guidance of lighting and electrical equipment design. For some of the requirements given in this standard, reference is made to data given in tables. For lamps not listed in such tables, the relevant data are supplied by the lamp manufacturer or responsible vendor. The performance requirements are additional to the basic requirements specified in IEC 60809. They are, however, not intended to be used by authorities for legal type-approval purposes. NOTE In the various vocabularies and standards, different terms are used for "incandescent lamp" (IEV 845-07-04) and "discharge lamp" (IEV 845-07-17). In this standard, "filament lamp" and "discharge lamp" are used. However, where only "lamp* is written both types are meant, unless the context clearly shows that it applies to one type only.

Lamps for road vehicles - Performance requirements

SANS 1329-4:2003 用于道路车辆的反光和荧光警告标志．第4部分：反光V形标志

This standard specifies requirements for retro-reflective chevron signs that incorporate a substrate and that are intended for use on motor vehicles that operate on public roads. NOTE Both the chevron signs and the motor vehicles have to comply with the relevant regulations of the Road Traffic Act, 1989 (Act 29 of 1989).

Retro-reflective and fluorescent warning signs for road vehicles Part 4:Retro-reflective chevron signs

KS R ISO 3267-2002(2007) 道路车辆前照灯清洁器

Road vehicles－Headlamp cleaners