43.040.60 车身及车身附件 标准查询与下载

T/CSAE 130-2020 汽车车身铝合金板材复合涂层 加速腐蚀试验方法

本标准规定了汽车车身铝合金板材复合涂层的加速腐蚀试验方法以及评价方法。

Accelerated corrosion test methods of composite coating for aluminum alloy sheets of automotive body

T/CSAE 131-2020 乘用车白车身防腐排水及密封设计指南

本标准规范了乘用车白车身防腐排水及密封设计步骤、各分级面的干湿分区和腐蚀环境等级，确立了白车身防腐排水及密封设计和防腐工艺方案选择原则。  本标准适用于乘用车白车身防腐排水及密封设计，其它车型的白车身防腐排水及密封设计指导规范可参考本标准。

The guideline of drainage and sealing design of sedan body in white for anticorrosion

ASTM F851-87(2020) 自升式座椅机构的标准测试方法

1.1 This test method evaluates the performance of selfrising or automatic-lifting seat mechanisms of chairs in places of assembly. 1.2 This test method addresses only the raising of the seat. It does not address the load that may be placed on that seat. Committee F15 is considering a standard addressing this load. 1.3 The values as stated in inch-pound units are to be regarded as the standard. The values in parentheses are provided for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Self-Rising Seat Mechanisms

ASTM D6479-15(2020) 用于确定充气式约束中使用的织物的抗皱性的标准测试方法

1.1 This test method covers the procedures for determining the resistance to edgecombing of a woven fabric used in inflatable restraints. 1.2 Procedures and apparatus other than those stated in this standard may be used by agreement of purchaser and supplier with the specific deviations from the standard practice acknowledged in the report. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Edgecomb Resistance of Woven Fabrics Used in Inflatable Restraints

KS I 4040-2019 小型货车用再制造后轮轴试验方法

Test methods for remanufactured rear axle of light duty commercial vehicles

QC/T 669-2019 汽车空调用管接头和管件

Pipe joints and fittings for automobile air conditioners

QC/T 663-2019 汽车空调用热力膨胀阀

Thermal expansion valve for automobile air conditioner

QC/T 664-2019 汽车空调制冷软管

Automobile air conditioning refrigeration hose

T/ZZB 1445-2019 汽车备胎升降器总成

本标准规定了汽车备胎升降器总成的术语和定义、 产品类型、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本标准适用于钢丝绳式汽车备胎升降器总成（以下简称备胎升降器）。

Spare tire lifter for vehicle

KS L 2007-2019 道路车辆安全眼镜

Safety glasses for road vehicles

T/CAAMTB 03-2019 汽车用橡胶和塑料密封条

本标准包括乘用车用橡胶密封条的技术要求、检验规则及标志、包装、运输和贮存的规定。适用 于基体材料为三元乙丙橡胶(EPDM)及热塑性弹性体(TPE)制造的各类密封条。 标准主要内容包括密封条（密实胶、海绵胶）尺寸公差和材料性能技术要求；密封条内金属骨架 尺寸公差和材料性能技术要求；密封条涂料涂层性能技术要求；有害物质限量要求；密封条成品技术指 标等共 17 个表，较全面涵盖了汽车密封条质量要求具体技术指标。

Rubber and plastic weather strips for automobiles

ASTM D7356/D7356M-19 使用氙弧曝光装置的汽车透明涂层加速酸蚀耐候性的标准测试方法

1.1 This test method covers an accelerated exposure test intended to simulate defects in automotive clearcoats caused by acid rain2 that occur at the Jacksonville, Florida exposure site. Exterior exposures at an acid rain test location in Jacksonville, Florida produce etch defects that range from small pits to 12.7 mm [0.5 in.] in diameter or larger acid-etched spots. The latter type of defect is not produced in other acid-etch tests that only produce pits that are smaller than 6.35 mm [0.25 in.] in diameter.3 NOTE 1—Digital images of the acid etch defects produced in outdoor acid-rain exposures and in the accelerated test described in this test method are found in Appendix X1. 1.2 The accelerated test described in this test method uses a xenon-arc light source with daylight filter conforming to the requirements of Practice G155. Specimens are sprayed with a simulated acid rain solution and requires the use of a horizontal, flat specimen array in order to allow the acid rain solution to remain on the test specimens for an extended period of time. 1.3 There is no known ISO equivalent to this test method. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Accelerated Acid Etch Weathering of Automotive Clearcoats Using a Xenon-Arc Exposure Device

QC/T 626-2019 汽车玻璃升降器

car glass regulator

QC/T 950-2019 汽车座椅加热垫技术要求和试验方法

本标准规定了汽车座椅加热垫的术语、技术要求、检验规则、标志、包装运输、储存的要求。 本标准适用于12V或24V电系的汽车座椅用加热垫。

Performance requirement and test of heating car cushion

QC/T 1119-2019 汽车安全玻璃术语

Automotive safety glass terminology

QC/T 661-2019 汽车空调用液气分离器

Liquid gas separator for automobile air conditioner

QC/T 660-2019 汽车空调用压缩机试验方法

Test methods for compressors used in automotive air conditioners

QC/T 1127-2019 乘用车麦弗逊悬架铝合金控制臂总成技术条件及试验方法

Technical conditions and test methods of aluminum alloy control arm assembly of McPherson suspension for passenger cars

QC/T 236-2019 汽车内饰材料性能的试验方法

Test methods for performance of automotive interior materials

KS I 4010-2019 汽车的再制造减震器

Test methods for remanufactured shock absorber of passenger cars